Theben LUXA 103-100 DE WH Manuel utilisateur

LUXA 103-100 DE WH

1030012

LUXA 103-101 DE WH

1030013

307343

Motion detector

1. Basic safety information

Danger of death through electric shock or fire!

 Installation should only be carried out by a

qualied electrician!

WARNING

•The device conforms with EN 60669-2-1 if installed

correctly

2. Proper use

•Motion detector for automatic lighting control dependent

on presence and brightness; LUXA 103-101 DE: suitable

for automatic lighting and HVAC control

•Suitable for ceiling installation (false ceilings) indoors

•Suitable for toilets, small rooms, workplaces, ofces, etc.

Disposal

Dispose of the device in an environmentally sound manner

(electronic waste)

3. Device description

Sensor unit

Power supply unit

3 potentiometers for setting

time delay (TIME), bright-

ness value (LUX) and detec-

tion area (metres);

additional setting of HVAC

time (TIME 2) in the case of

LUXA 103-101 DE

red LED

4. Installation and connection

!Secure device with an upstream type C circuit breaker

(EN 60898-1) with a maximum of 10 A.

!Secure device with an upstream type C circuit breaker

(EN 60898-1) with a maximum of 6 A (HVAC channel 2).

Installing the motion detector

LInstallation height: 2 – 3 m

LCable length: 100 cm

LMotion detector requires clear line of sight to people

Disconnect power source

0FF

230V

Create a ceiling opening of Ø 65 mm

=65

6 - 8 m m

5 0 - 6 0 m m

Screw open and ip open the power supply unit

Connect power supply unit and sensor unit according to the

wiring diagram

LRecesses in the power supply unit can be adjusted to the

cable diameter (min. Ø 3 - max. Ø 12.5 mm)

Ø 3 - Ø 6 mm Max. Ø 12.5 mm

!ATTENTION: the network connector must be rmly in place

Push the power supply unit through the ceiling opening

and attach the sensor with tensioned springs in the ceiling

Ø= 65

Connect motion detector to power supply

The device need

60 seconds to warm up.

Connecting the motion detector

Danger of death through electric shock or fire!

 Installation should only be carried out by a

qualied electrician!

WARNING

Disconnect power source

Ensure device cannot be switched on

Check absence of voltage

Earth and bypass

Cover or shield any adjacent live components

The warm-up phase takes approx. 60 s. The LED is perma-

nently red.

L NLL‘ N R

L NL N R D1 D2

L‘

LUXA 103-100 DE LUXA 103-101 DE

Installation instructions and detection area

As the detector reacts to variations in temperature, avoid the

following situations:

Do not direct motion detectors at objects with highly-

reective surfaces such as mirrors, etc.

Do not install the motion detector near heat sources, such

as heating outlets, air conditioning systems, lamps, etc.

Do not direct the motion detector at objects that move in

the wind, such as curtains, large plants, etc.

Pay attention to the direction of motion during the test run.

3,5 m

4 m

7 m

2 m

Lrecommended installation height: 2.5 m

5. Walking test

The walking test is used to test the detection area.

Set the time delay potentiometer (TIME 1) to Test. The

motion detector only reacts to movements, brightness

measurement is switched off.

Walk through the detection area. Every detected movement

is indicated by the LED, and the light switch contact closes

for 2 s.

2 sec

Test

OPEN

2030 10



6. Setting

The motion detector LUXA 103-100 DE has 3 potentiome-

ters for setting the time delay (TIME 1), brightness (LUX) and

sensitivity (METRES); with LUXA 103-101 DE the HVAC time

(TIME 2) can also be set.

LUXA 103-101 DE



Setting the brightness (LUX)

You can set different brightness values (LUX) with the

potentiometer.

If you want to change the preset brightness

Set the potentiometer to the desired brightness

(10 – 2000 lux = )

If you want a specic brightness value to be learned using the

teach-in function

At the desired brightness, set the potentiometer to . The

LED ashes for 20 s, afterwards the measured brightness

value is accepted.

Leave the potentiometer at position .

Setting the time delay (TIME 1)

If the motion detector detects no further movement, it swit-

ches off after the set time delay.

If you want to change the preset time

Set the potentiometer to the desired time (5 s - 30 min).

If you want to use the pulse function (e.g. for a staircase light

timer switch)

Set the potentiometer to . The presence detector for

"staircase light timer switch" operation is on for 1 s and off

for

9 s.

Setting the HVAC time (TIME 2) (only LUXA 103-101 DE)

Set the potentiometer to the desired time (10 s - 60 min.).

Setting the sensitivity (METRES)

You can reduce the sensitivity in order to avoid switching

errors.

Set potentiometer METRES to the desired

sensitivity.

Manual operation

The lighting can be manually switched on/off via a button.

L NLL‘ N R

When the light is on

Briey press button once (< 1 s)

▻Light is off

When the light is off

Briey press button once

▻The light is on for the time set on the potentiometer;

then the detector goes into automatic mode

Limiting the detection area

Use the supplied cover clips to adjust the motion detector

to the desired detection area.

Remove the required section of the cover clip by using

pliers or similar.

Then place it on the lens.

7. Technical data

Operating voltage 230 V AC ±10%

Frequency 50 Hz/60 Hz

Upstream protection device 10 A

Standby output 0.5 W

Switching capacity min. 10 mA

Protection rating IP 44 (detector), IP 20 (power supply

unit) in accordance with EN 60529

Protection class II

Operating temperature 0 °C … +45 °C

Brightness setting range 10 – 2000 lx/∞

Duty cycle range LUXA 103-100: 5 s – 30 min for

lighting

LUXA 103-101: 5 s – 30 min for

lighting

10 s – 60 min for HVAC

Detection angle 360°

Detection area lateral/frontal: 7 m/4 m

Installation height 2 – 3 m (2.5 m recommended)

Light switch output µ contact 230 V AC, zero-cross

switching

Switch output HVAC (D1/D2) LUXA 103-101: 5 A (at 250 V AC,

cos ϕ= 1) µ contact

Min. switching capacity 10 mA

Incandescent lamp load max. 2000 W

Halogen lamp load max. 2000 W

Low-voltage halogen lamps

(transformer)

max. 1000 VA

Fluorescent lamps (LLB low-loss

ballasts):

parallel compensated

max. 900 VA, 100 µF

Fluorescent lamps (EB – electronic

ballasts)

600 W

Compact uorescent lamps (EB) 400 W

LED lamps (< 2 W) 35 W

LED lamps (> 2 W) 400 W

8. Contact

Theben AG

Hohenbergstr. 32

72401 Haigerloch

GERMANY

Tel. +49 7474 692-0

Fax +49 7474 692-150

Hotline

Tel. +49 7474 692-369

[email protected]

Addresses, telephone numbers etc.

www.theben.de

Ce manuel convient aux modèles suivants

Autres manuels Theben Capteur de sécurité

Theben

Theben thePixa P360 KNX UP WH Manuel utilisateur

Theben

Theben thePixa P360 24V KNX UP WH Manuel utilisateur

Theben

Theben theLeda D S AL Manuel utilisateur

Theben

Theben TIMEGUARD LEDPROPCB Manuel

Theben

Theben Luxa 103-200 Manuel utilisateur

Theben

Theben thePassa P360-221 DALI UP WH Manuel utilisateur

Theben

Theben theRonda P360-110 DALI UP WH Manuel utilisateur

Theben

Theben thePiccola P360-100 DE Manuel utilisateur

Theben

Theben TIMEGUARD PDFM361AB Manuel

Theben

Theben thePixa P360 KNX UP WH Manuel utilisateur

Theben

Theben thePrema S360-101 E UP WH Manuel utilisateur

Theben

Theben theMura S180-100 UP WH Manuel utilisateur

Theben

Theben theMova S360-101 DE WH Manuel utilisateur

Theben

Theben 201 9 290 Manuel utilisateur

Theben

Theben thePiccola P360-100 DE Manuel utilisateur

Theben

Theben theMura S180-100 UP WH Manuel utilisateur

Theben

Theben theRonda S360 KNX UP WH Manuel utilisateur

Theben

Theben thePassa P360-101 UP WH Manuel utilisateur

Theben

Theben thePrema S360 DALI UP WH Manuel utilisateur

Theben

Theben thePrema P360-101 E UP WH Manuel utilisateur

Theben

Theben ECO-IR DUAL-C NT Manuel utilisateur

Theben

Theben PlanoCentro 000-E Series Manuel utilisateur

Theben

Theben theRonda P360-330 DALI UP WH Manuel utilisateur

Theben

Theben PlanoCentro 101-E Series Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur