Texas Instruments SmartRF CC900DBK Manuel de programmation

Table des matières

Autres manuels Texas Instruments Carte mère

Texas Instruments

Texas Instruments LMG34BB-EVM Series Manuel utilisateur

Texas Instruments

Texas Instruments TAA5242EVM-K Manuel utilisateur

Texas Instruments

Texas Instruments Chipcon CC2430DB Manuel utilisateur

Texas Instruments

Texas Instruments TUSB1146 Manuel utilisateur

Texas Instruments

Texas Instruments LMK5C33216EVM Manuel utilisateur

Texas Instruments

Texas Instruments LMK04832SEPEVM Manuel utilisateur

Texas Instruments

Texas Instruments TPS274C65CP Manuel utilisateur

Texas Instruments

Texas Instruments TPL5111EVM Manuel utilisateur

Texas Instruments

Texas Instruments LM2796 Manuel utilisateur

Texas Instruments

Texas Instruments TPA6020A2 Manuel utilisateur

Texas Instruments

Texas Instruments TLV3607 Manuel utilisateur

Texas Instruments

Texas Instruments TPS62233EVM-574 Manuel utilisateur

Texas Instruments

Texas Instruments DRV2603 Manuel utilisateur

Texas Instruments

Texas Instruments UCC25660 Series Manuel utilisateur

Texas Instruments

Texas Instruments TPS62806-7-8EVM083 Manuel utilisateur

Texas Instruments

Texas Instruments TPS60120EVM-174 Manuel utilisateur

Texas Instruments

Texas Instruments bq24070/1 Manuel utilisateur

Texas Instruments

Texas Instruments DAC82002EVM Manuel utilisateur

Texas Instruments

Texas Instruments ADC161S626 Manuel utilisateur

Texas Instruments

Texas Instruments DS90UB954-Q1EVM Manuel utilisateur

Texas Instruments

Texas Instruments AN-1993 LM3406HV Manuel utilisateur

Texas Instruments

Texas Instruments TPS2549Q1EVM-729 Manuel utilisateur

Texas Instruments

Texas Instruments LP8557EVM Manuel utilisateur

Texas Instruments

Texas Instruments LM73605 Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur

SWRU063

Quick Start Instructions

Rev. 1.1

SmartRF

®

CC900DBK Demonstration Board Kit

SWRU063 Page 2 of 2

How to get a quick start using CC900DBK

The CC900DBK Demonstration Board Kit demonstrates the CC900 RF transceiver in a very

simple application. The Demonstration Board includes a complete CC900 transceiver, an

AVR micro-controller, an integrated PCB antenna and a battery. It provides a complete

example of a low-cost, low-power system using the CC900 transceiver. Please note that the

design is optimised for low cost applications and not for maximum range. In order to evaluate

range and performance, use the CC900DK.

Important:

•Do NOT short-circuit the battery terminals at any time.

•The use of radio transceivers is regulated by international and national rules. Before

transmitting a RF signal, please contact your local telecommunication authorities to check

if you are licensed to operate the transceiver.

To get the Kit up and running, follow these steps:

1. The CC900DB runs off a 3.6V Lithium battery. If the battery is not mounted, solder it to

the pads at the rear side of the board.

2. Examine the LED. If it does not blink at regular intervals, push the “ON” button.

3. If the LED still does not blink, remove the battery and reconnect it. If this does not help,

exchange the battery with a new one.

4. Press the “ON” buttons on both Demonstration Boards so that both are blinking. They are

now in polling reception mode, checking for data each time the LED is lit.

5. Press the “TX” button on one of the boards. The demonstration board sends a data

packet of approximately 1.5 second duration.

6. If the other demonstration board received the message without errors, its LED will blink

the Morse code for “victory”. It then sends an acknowledgement message in return.

7. If the first board receives the acknowledgement message, it will also blink “victory” in

Morse code.

If a demonstration board has not received a message or had any buttons pressed for two

minutes, it will enter power-down mode, ensuring minimum power consumption. To wake it,

press the “On” button.

If communication does not succeed on the first attempt, try again. RF noise may have

corrupted the message. Signal processing in the small micro-controller has been kept to a

minimum, therefore a small noise burst may corrupt the message. When holding the

demonstration board, do not touch the antenna or the VCO tank. Ideally, keep your hand as

far away from the antenna as possible in order to get the best performance. If you wish to

reprogram the Demonstration Board using the Development Kit, make sure to:

•Use the cable supplied in the Development Kit

•Remove the battery when reprogramming

•Use the correct parallel port. If you are using the correct port, you will receive an error

message if you try to program the EEPROM and no Demonstration Board is inserted

For further information, see the CC900DB Demonstration Board User Manual, which can be

downloaded from our website (http: www.chipcon.com)