Texas Instruments TI-92 Mode d’emploi

Installing Texas Instruments TI-92 Motherboard

In this guide we will show how to access the motherboard and how to separate it from other internal

components.

Need to place picture

Installing Texas Instruments TI-92 Motherboard

Step 1 - Back Cover

The first step to any repair operation is to

remove the front cover.

Grab the back of the calculator with one hand and the

cover with the other.

Pull the cover off from one of the sides for easy

removal.

Step 2

Orientate the calculator with the top facing towards you.

Slide the locking tab,found on the top part of the

calculator, to the unlock position.

Installing Texas Instruments TI-92 Motherboard

Step 3

"Locking Tab"

To remove the back cover, slide the cover away from

the locking tab towards the bottom of the calculator until

the cover no longer slides.

Then with the front of the calculator facing down, pull

up on the back cover.

The calculator should now be orientated with the front

facing down, as shown in picture 2.

Step 4 - Batteries

The Batteries are now exposed and the

calculator is face down with the back

towards you.

Remove the bottom batteries by pressing the battery

towards you while pulling it out from the far end.

If you can not do the previous step with your

finger try using a flat ended tool such as an

Ipod opening tool.

After the bottom battery has been removed push or

slide the other(top) battery towards you until it is fully

exposed in the battery slot.

Now simply remove the battery.

Installing Texas Instruments TI-92 Motherboard

Step 5 - repair Back Case

Using a Philips Screwdriver #00 unscrew the twelve

11.8mm screws shown in the picture and located on the

back of the calculator.

Step 6

Unscrew the 19mm screw located near center of the

back of the calculator.

Remove the panel being held by the screw.

Installing Texas Instruments TI-92 Motherboard

Step 7

Using the same Phillips screwdriver, unscrew the

remaining three 11.8mm screws.

Step 8

Using the Ipod Opening Tool pull up on both sides of

the rectangular module while keeping the rest of the

calculator flat on a surface face down

You may get a lot of resistance from the

module. Do not use too much force as you

risk damage. Use small amounts of force to

work the module out.

Installing Texas Instruments TI-92 Motherboard

Step 9

Pull out the rectangular module when it is finally loose

enough.

Step 10

Now pull up on the back cover of the calculator while

holding the rest of it flat on a surface.

Be careful not to tilt the front of the

calculator at this point. The keyboard

buttons are now unsupported and will fall

out of place.

Installing Texas Instruments TI-92 Motherboard

Step 11 - Motherboard

Pull the motherboard up while holding the rest of the

calculator firmly in place

The motherboard has now separated from the rest of

the calculator

To reassemble your device, follow these instructions in reverse order.

This document was last generated on Dec 14, 2010.

Installing Texas Instruments TI-92 Motherboard

Autres manuels pour TI-92

Table des matières

Autres manuels Texas Instruments Calculatrice

Texas Instruments

Texas Instruments TI-84 - Plus - Edition Graphing Calculator Manuel utilisateur

Texas Instruments

Texas Instruments TI-84 Plus CE Python Manuel utilisateur

Texas Instruments

Texas Instruments El Dorado CS-FX300MS PLUS Manuel utilisateur

Texas Instruments

Texas Instruments TI-30XS Multiview Manuel utilisateur

Texas Instruments

Texas Instruments TI-Nspire CX II Series Manuel utilisateur

Texas Instruments

Texas Instruments MathPrint TI-30X Plus Manuel utilisateur

Texas Instruments

Texas Instruments TI-5045SV Manuel utilisateur

Texas Instruments

Texas Instruments CBL Manuel utilisateur

Texas Instruments

Texas Instruments Titanium TI-89 Manuel utilisateur

Texas Instruments

Texas Instruments TI-31 Solar Manuel utilisateur

Texas Instruments

Texas Instruments TI-73 Explorer Guide de démarrage rapide

Texas Instruments

Texas Instruments TI-83 - Plus Graphing Calculator Manuel

Texas Instruments

Texas Instruments Titanium TI-89 Instructions de montage

Texas Instruments

Texas Instruments TI-5045SVC Manuel

Texas Instruments

Texas Instruments TI-Nspire Manuel

Texas Instruments

Texas Instruments TI-Nspire Manuel utilisateur

Texas Instruments

Texas Instruments TI-Nspire Mise à jour du firmware

Texas Instruments

Texas Instruments Titanium TI-89 Manuel utilisateur

Texas Instruments

Texas Instruments Titanium TI-89 Mode d’emploi

Texas Instruments

Texas Instruments TI-73 Explorer Manuel

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Manuel utilisateur

Texas Instruments

Texas Instruments TI-Nspire CX Manuel utilisateur

Texas Instruments

Texas Instruments TI Voyage 200 Manuel utilisateur

Texas Instruments

Texas Instruments TI-82 STATS Manuel utilisateur

Manuels Calculatrice populaires d'autres marques

HP 35s Manuel

Casio

Casio CFX-9970G Manuel utilisateur

LEXIBOOK

LEXIBOOK EL350 Manuel utilisateur

HP HP-97 Manuel utilisateur

Citizen

Citizen SDC-414N Manuel utilisateur

Casio

Casio fx-3800P Manuel utilisateur

Canon

Canon P26-DHIII Manuel utilisateur

Citizen

Citizen 520DPA Manuel utilisateur

Sharp

Sharp EL-9900 Manuel utilisateur

Casio

Casio FX-9860GII - SOFTWARE VERSION 2-00 Manuel utilisateur

Casio

Casio MS-7UC Manuel utilisateur

Sharp

Sharp WriteView EL-W506 Manuel technique

Casio

Casio FC-200 Manuel utilisateur

Casio

Casio fx-CG50 Manuel utilisateur

HP HP-67 Guide de l'utilisateur

Royal

Royal CBC2000 Manuel utilisateur

Heathkit

Heathkit IC-2009 Manuel utilisateur

Universal

Universal UNV-15907 Manuel utilisateur