TESTO 606-1 Manuel utilisateur

Instruction manual

testo 606-1

99 Washington Street

Melrose, MA 02176

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

11

Short manual testo 606-1

Protection cap: Park position

Sensing electrodes

Display

Control keys

Battery compartment (on rear)

Test resistance contact

List of settable materials, for

sticking into the protective cap

Basic settings

Instrument off > press and hold 2s > select with ( ),

confirm with ( ):

Auto off-Funktion: OFF,ON

Switching the instrument on

Press .

Switching the display light on(for 10s)

Instrument on > press

Select display mode

Instrument on > select with :

Current reading > Hold: Readings are held

Switching the instrument off:

Instrument on >press and hold 2s.

de

enfresitptsvnl????

Short manual testo 606-1

12

Safety and the environment

About this document

iPlease read this documentation through carefully and

familiarise yourself with the product before putting it to use.

Keep this document to hand so that you can refer to it when

necessary. Hand this documentation on to any subsequent

users of the product.

iPay particular attention to information emphasised by the

following symbols:

With the signal word Caution!:

Warns against hazards which could result in minor physical injury

or damage to equipment if the precautionary measures indicated

are not taken.

Important.

Avoid personal injury/damage to equipment

iOnly operate the measuring instrument properly, for its

intended purpose and within the parameters specified in the

technical data. Do not use force.

iNever store the product together with solvents, acids or other

aggressive substances.

iOnly carry out the maintenance and repair work that is

described in the documentation. Follow the prescribed steps

when doing so. Use only OEM spare parts from Testo.

Protecting the environment

iTake faulty rechargeable batteries as well as spent batteries to

the collection points provided for them.

iSend the product back to Testo at the end of its useful life. We

will ensure that it is disposed of in an environmentally friendly

manner.

Safety and the enviroment

13

Specifications

Functions and use

The testo 606-1 is a material moisture measuring instrument. It is

normally used to determine the material moisture content in wood

or building materials. The measurement procedure used is

suitable for overview measurement to determine whenther the

material is continuing to dry out. The material moisture is given in

% by weight.

Measurement data

· Sensors:

Electrical resistance (conductivity

measurement), Testo humidity sensor,

NTC temperature sensor

· Parameters:

% by weight material moisture (wood,

building materials), %rH, td, wb, °C, °F

· Measuring ranges:

See chapter Using the Product

· Resolutions:

0.1 %, 0.1 °C, 0.1 °F, 0.1 %rH

· Accuracies (Nominal temperature

25 °C, ±1 Digit):

Conductivity measurement ±1 %,

±0.5 °C, ±0.9 °F,

±2.5%rH (5...95%rH)

· Measuring rate:

0.5 s, humidity: 1s

Further instrument data

· Protection class: IP20

· Ambient conditions:

-10...50 °C, 14...122 °F

· Storage/transport conditions:

-40...70 °C, -40...158 °F

· Voltage supply:

2x 1.5 V type AAA

· Battery life:

130 h (without display light)

· Dimensions:

119x46x25mm / 4.69x1.81x0.98” (inc.

protection cap)

· Weight: 90 g / 3.2 oz (inc. batteries and

protection cap)

Directives, standards and tests

· EC Directive: 2004/108/EEC

Warranty

· Duration: 2 years

· Warranty conditions: see guarantee

card

de

enfresitptsvnl????

Specification

14

Product description

At a glance

Protection cap: Park position

Sensing electrodes

Caution! Risk of injury

from sensing electrodes!

iAttach protection cap

when not in use.

Display

Control keys

Battery compartment (on rear)

Test resistance contact

List of settable materials, for

sticking into the protective cap

First steps

²Inserting batteries:

1To open the battery compartment, push the battery cover

down.

2Insert batteries (2x 1.5 V type AAA). Observe the polarity!

3To close the battery compartment, push the battery cover

back on.

²Basic settings (configuration mode):

Adjustable functions

· Auto off function: OFF,ON (instrument switches off automatically if no key is

pressed for 10 minutes)

1When switching the instrument on, press and hold until

and appear on the display (configuration mode).

- The adjustable function is displayed. The current setting

flashes.

2Press ( ) several times until the desired setting flashes.

Product description

15

3Press ( ) to confirm the input.

- The instrument changes to measuring mode.

Using the product

To ensure correct readings, repeat the measurement at several

points. Always measure wood moisture across the grain.

The values displayed are highly dependent on the building

material/manufacturer used, and on the ambient conditions .

As the materials are natural, the same materials can vary from

batch to batch.

²Switching the instrument on:

iPress .

- Measuring mode is opened.

²Switching the display light on:

The instrument is switched on.

iPress .

- The display light goes out automatically if no key is

pressed for 10 seconds.

²Setting the material characteristic curve:

The material moisture is indicated in the top line of the

display. The material symbol (wood) or (building

material) is displayed with the relevant material number (see

enclosed sticker for the inside of the protective cap).

Settable materials Measuring range

1. beech, spruce, larch, birch, cherry, walnut 8.8...54.8 % by weight

2. oak, pine, maple, ash-tree, douglas fir, meranti 7.0...47.9 % by weight

3. cement screed, concrete 0.9...22.1 % by weight

4. anhydrite screed 0.0...11.0 % by weight

5. cement mortar 0.7...8.6 % by weight

6. lime mortar, plaster 0.6...9.9 % by weight

7. bricks 0.1...16.5 % by weight

iPress several times until the desired material

characteristic curve appears.

²Testing the instrument function:

1Press several times until Test: lights up.

de

enfresitptsvnl????

Using the product

16

2Connect sensing electrodes with the contacts of the test

resistor on the top of the protection cap.

-Test flashes.

-Test: ok lights up: instrument is functioning.

Test: ok does not light up: test not possible, see chapter

'Tips and assistance'.

3Press back to measurement menu.

²Changing the display view:

Adjustable views

· Current reading

·Hold: Readings are held.

iPress until the desired view appears.

²Switching the instrument off:

iPress and hold until the display goes out.

Maintaining the product

±Changing batteries:

1To open the battery compartment, push the battery cover

down.

2Remove used batteries and insert new batteries

(2x 1.5 V type AAA). Observe the polarity!

3To close the battery compartment, push the battery cover

back on.

±Cleaning the housing:

iClean the housing with a moist cloth (soap suds) if it is dirty.

Do not use aggressive cleaning agents or solvents!

Using the product

17

Tips and assistance

Questions and answers

Question Possible causes/solutions

Hi or Lo · Readings outside the measuring range (too high, too

low): Keep to the permitted measuring range.

· Residual capacity <10 min: Change batteries.

Testing the instrument

function: Test: ok does

not light up · Clean sensing electrodes and contacts on the top

of the protection cap.

· If the error message appears again, send the

instrument to Testo Customer Service.

Meas. electrodes defective/

worn · Send instrument to Testo customer service.

Typical values for equilibrium moisture (Air dryness in building

materials1):

Material Char. curve Material moisture

Anhydrite screed 4 <0.5 % by weight

Concrete 3 <2.2 % by weight

Plaster 3 <0.8 % by weight

Lime mortar 6 <2.0 % by weight

Brick, fireded

without hole 7 <1.0 % by weight

Cement screed 3 <3.0 % by weight

Cement mortar 5 <3.0 % by weight

1In ambient conditions of 20 °C and 65 % RH

Guideline values for the installation moisture of wood, which sets

in as an average after a certain period in use-status (DIN 1052-1

(4/88) Para. 4.2.1.):

Char. curve Application area Wood humidity in % by weight

1 or 2 buildings closed on all sides with heating 9 ± 3

1 or 2 buildings closed on all sides without heating 12 ± 3

1 or 2 roofed open buildings 15 ± 3

1 or 2 constructions which are open to the weather on all sides 18 ± 6

If we could not answer your question, please contact your dealer

or Testo Customer Service.

de

enfresitptsvnl????

Tips and assistance

18

Test Equipment Depot - 800.517.8431

99 Washington Street,Melrose, MA 02176

TestEquipmentDepot.com

0973.6063/03/Sh/dr/30.04.2008

Test Equipment Depot - 800.517.8431

99 Washington Street,Melrose, MA 02176

TestEquipmentDepot.com

Autres manuels pour 606-1

5

Table des matières

Autres manuels TESTO Instrument de mesure

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur