Teltonika RUT240 Manuel utilisateur

Installation Manual - Swiftlane Cellular Router

Installation Manual - Swiftlane Cellular Router 1

Parts information 1

Network 2

Wiring diagrams 3

Option 1: Using an external antenna, for cellular only internet 3

Option 2: Using external antenna and cellular as a backup to primary wired internet

Option 3: Using the cellular router without an external antenna 4

Mounting Considerations for External Antenna 6

Height 6

Direction 6

Checking Signal Strength and Connectivity 7

Please use an Ethernet to USB converter so that you can connect to the cellular router

locally on a computer. 7

Router login 8

Setting up cellular failover to the WAN (wired internet) 13

Antenna Location 13

Location of towers 16

Debugging 17

Changing the static IP of the RUT240 17

Checking what devices are connected to the router 18

References 19

Parts information

Type

Product

Name

Summary and Datasheets

Photo

Cellular Router

RUT240

RUT240 cell router website

Omni-direction

al antenna

QuSpot

Link

External antenna with antennas in 4

directions. Utilized in urban environments

with lots of diﬀerent tower locations nearby

Uni-directional

antenna

QuMax

Link

External antenna with single direction of

antenna. Strongest gain in one direction,

ideal for suburban and remote locations

Passive POE

injector - 24V

Passive

POE 24V

Link

Used to power the RUT240 router, through

the LAN port. Warning: RUT240 does not

support standard POE, which would burn the

router. Only use this passive POE that’s 24V

DC output.

Network

Swiftlane uses AT&T as the primary provider for cellular connectivity. Please check the

general signal strength at the customer site, you can request this information ahead of

time from the customer or during your initial site assessment.

Wiring diagrams

Option 1: Using an external antenna, for cellular only internet

If Swiftlane provided internet is being used as the primary internet service, please follow

these wiring options. An external antenna is strongly recommended in this scenario to

maximize signal strength, especially since the signal can be weaker in server and IDF rooms

Option 2: Using external antenna and cellular as a backup to primary

wired internet

Option 3: Using the cellular router without an external antenna

If the signal strength inside the server room is strong, an external antenna may not be

required, and you can use the antennas that come bundled with the RUT240 router

Mounting Considerations for External Antenna

External antennas should be mounted outside the building with minimal obstruction from

nearby buildings. Identify the location that balances ease of installation with the maximum

unobstructed views, in order to achieve best gain from the antenna

●Balance ease of installation with aesthetic considerations for the building, and

minimal obstructions from nearby building

●For uni-directional antenna, the mount provides a 45 degree rotation angle, in order

to adjust the antenna horizontally and align with the nearby tower

●Use cellmapper.net to identify nearby towers to ensure maximum gain on the

antenna

Height

In general, the taller the antenna is placed, the better it will perform. However, 10-12 ft is a

good installation height to start. This protects it from easy access to vandalism, while also

getting few obstructions to the nearby towers. You can connect the antenna and hold it up

at that height and check the signal strength indicators by connecting to the local

management dashboard over an IP connection. Follow the instructions below to get

familiar with the various parameters for signal strength.

Direction

Omni - directional antennas capture signal strength from all directions so they dont to be

pointing in any speciﬁc direction

Uni-directional antennas must be pointed in the general direction of the nearest cell towers

for AT&T. You can use https://www.cellmapper.net/ to insert the full address and look up

nearby 4G towers.

Checking Signal Strength and Connectivity

Please use an Ethernet to USB converter so that you can

connect to the cellular router locally on a computer.

Remove the ethernet cable connected to the non-red side of the white POE injector, and

plug that into your computer.

In a browser, connect to

192.168.1.1

Router login

Username: admin

Password:

Please contact [email protected] to request the password

Connect to the IP address 192.168.1.1 in the browser.

Go to network - mobile tab

Look under the section called “Network Frequency Bands” -> Connection Method

Set the “connection method” to automatic

This will restart the router. After a few min, you can log back in again and check this page

Go to Status -> Network

It wi

It will show you the signal strength and the “connected Band” in there.

Autres manuels pour RUT240

Table des matières

Autres manuels Teltonika Routeur réseau

Teltonika

Teltonika RUT905 Manuel utilisateur

Teltonika

Teltonika RUT240 Manuel utilisateur

Teltonika

Teltonika RUT360 Manuel utilisateur

Teltonika

Teltonika RUT850 Manuel utilisateur

Teltonika

Teltonika RUT956 Manuel utilisateur

Teltonika

Teltonika RUT950 LTE Manuel utilisateur

Teltonika

Teltonika TRB145 Manuel utilisateur

Teltonika

Teltonika FM3622 Manuel utilisateur

Teltonika

Teltonika RUTX08 Manuel utilisateur

Teltonika

Teltonika RUT240 Manuel utilisateur

Teltonika

Teltonika RUT850 Manuel utilisateur

Teltonika

Teltonika RUT240 Manuel utilisateur

Teltonika

Teltonika FMx 640 Manuel utilisateur

Teltonika

Teltonika RUT955 Manuel utilisateur

Teltonika

Teltonika RUTX08 Manuel utilisateur

Teltonika

Teltonika FMB002 Manuel utilisateur

Teltonika

Teltonika QSG RUT951 Manuel utilisateur

Teltonika

Teltonika RUT240 Manuel utilisateur

Teltonika

Teltonika QSG RUT955 Manuel utilisateur

Teltonika

Teltonika RUT905 Manuel utilisateur

Teltonika

Teltonika QSG RUTM50 Manuel utilisateur

Teltonika

Teltonika FM36M1 Manuel utilisateur

Teltonika

Teltonika RUT955 Manuel utilisateur

Teltonika

Teltonika RUT955 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité