Teltonika ModemCOM/G10 Manuel utilisateur

Address: Žirmūnųg. 27, Vilnius LT-09105,

Tel.: +370 5 2127472,

Fax: +3705 276 1380, E-mail: [email protected]

ModemCOM/G10

(CM1100)

Quick Start v0.1

Thank you for purchasing our device! We hope this feature-packed, user-friendly device will

satisfy your expectations. Please take few minutes to read this Quick Start Guide before starting to

work with ModemCOM/G10. This would make the installation and use of the device easier.

INTRODUCTION

This Quick Start Guide has been prepared for Windows XP (SP2) operating system. For

installation guide on other supported operating systems, please refer to User Guide provided on CD.

ModemCOM/G10 is a device designed for data transmission via GSM Network. The design of this

modem enables the connection to your PC through COM interface. Once connected to the PC, you can

send SMS or access the Internet via one of the data transmission types supported by your GSM operator.

ModemCOM/G10 supports the following data-bearers: GPRS, CSD and SMS.

CONTENT OF YOUR PACKAGE

1) ModemCOM/G10 device.

2) COM extension cable.

3) CD (including drivers and appropriate documentations).

4) Quick Start Guide.

If any of the components are missing please contact your local distributor.

HOW TO BEGIN?

Before you begin make sure that:

You are using Windows XP operating system with SP2 installed and you personal

computer hardware meets minimal requirements of this operating system. For

installation guide on other supported operating systems, please refer to User Guide

available on CD.

You have a GSM SIM card with activated data transfer service.

ModemCOM/G10 is ready to work – SIM card is pushed in.

Dial-up networking is installed on your PC (OS) (this should be installed with OS by

default).

TCP/IP protocol is installed on your PC (it should be present in your OS by default).

INSTALLING THE MODEM CONTROL TOOL

Notice: Whenever the driver installation is going to be performed, the modem should be unplugged

from the PC!

Open the ModemCOM/G10 package, take out the CD and insert it into your CD drive. Click Install in

automatically opened window. If the window did not appear, run autorun.exe file located on the CD. The installation

procedure of the ModemCOM/G10 modem will begin.

Advanced User: Can press Browse button to

choose specific folder where you wish to install

Modem Control Tool.

SETTING UP AN INTERNET CONNECTION

Using ModemCOM/G10 you can access the Internet via one of the following data transmission

types:

GPRS packet data transfer. In this case you have to know the APN, User Name and

Password (all these parameters would be provided by your GSM operator).

CSD data transfer. You have to know the phone number of a dial-up server (all these

parameters would be provided by your GSM operator).

In this section we will provide you with general information and procedures necessary for setting up

an Internet connection to your PC.

If GPRS data transfer is used, you have to set up an APN (Access Point Name), Phone Number, User

Name and Password if necessary (all these parameters would be provided by your GSM operator). If you

are using CSD, you have to know the phone number of the dial-up server. Setting up an Internet

connection to your PC:

1) Start the Modem Control Tool.

2) Select Settings -> Connection.

3) Enter the APN, User Name and Password (user name and password are not always

needed; it depends on your network operator).

4) Enter the Phone Number: *99#.

5) Click Update after the data was entered.

Connecting to the Internet

Make sure, that the SIM card is properly inserted into device, the device is properly connected to

the PC its „Power“LED is ON and the drivers are installed properly.

Start the Modem Control Tool program. The program can be started from the PC desktop by

double-clicking on the Modem Control Tool G10 shortcut (or Start -> Programs -> Teltonika ModemCOM

G10 -> Modem Control Tool COM G10).

1) The program should automatically detect a connected modem. If this does not happen,

select Settings->Main. Select present modem from list of modems and click Set as

current modem button.

2) When Connect is clicked, the modem will start establishing connection to the Internet.

Sending SMS

Note: Please make sure that SMS service is supported by your operator. Please ensure that a SMS

centre number is entered (Modem Control Tool -> Settings -> SMS). If it isn’t, ask your GSM operator

for the SMS centre number and enter it manually.

To continue installation plug in your

ModemUSB/G10 now and click OK

SMS sending sequence:

1) Run Modem Control Tool.

2) Click SMS.

3) Enter recipient’s phone number.

4) Enter the text.

5) Click Send.

Wait for a dialogue box, which will inform you about successful or unsuccessful procedure.

INDICATION

A LED indicator “Power“ is“ is located on the side of ModemCOM/G10. This LED indicates the

operating mode and failure conditions of the modem.

“Power“ is“ LED‘s Status Modem status

„Power“ LED is on Modem power supply is on

„Power“ LED is off Modem power supply is off

A LED indicator “Status“ is“ is located on the side of ModemCOM/G10.

This LED indicates the operating mode and failure conditions of the modem.

“Status“ is“ LED

colour LED Status Modem Description

Green ON Modem ready

Green Slow blink Initialization

Green Double blink Limited service PIN/PUK required

Orange Continuously blinking Network absent

Orange Slow blink GPRS fail

Orange Double blink No SIM

TROUBLESHOOTING

1) Problem: Modem Control Tool does not detect the modem.

Solution 1: Remove and insert back the modem, check if the SIM card inserted properly.

Solution 2: Check if the device is properly connected and Power LED is on. Also check if the modem is being

displayed in “Windows Phone and Modem Options” (control panel) Modems menu. If not remove the modem

and insert it back. If removing the modem does not help, please try to reboot your PC.

Solution 3: Check if the drivers are installed properly. Driver status you can checked in Windows Device

Manager, if there will be problems with the Modem or COM ports, please uninstall the software and try to

install it again. If does not help contact your local distributor.

2) Problem: Can’t connect to the Internet.

Solution: Check if the network parameters are entered correctly.

3) Problem: If Windows/Modem Control Tool cannot find the modem when it is physically connected to different

COM port.

Solution: If the modem is inserted into a COM port other than the port in which it was inserted previously,

please wait until Windows detects the device and installs the drivers automatically. If this does not happen,

please uninstall and install it again.

This sign on the package means that it is necessary to read the User Manual,

which is on the CD before you start using the device.

This sign on the package means, that used electronic and electric equipment

should be stored separately.

FINAL NOTES

For more information, please read the ModemCOM/G10 User Manual present on the CD. If you face any problems

related to the device, which you are not able to solve by yourself, please contact your local distributor they would be

glad to help you.

Autres manuels pour ModemCOM/G10

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Teltonika Modem

Teltonika

Teltonika H1.8 Manuel utilisateur

Teltonika

Teltonika TRM250 Manuel utilisateur

Teltonika

Teltonika ModemCOM/G10 Manuel utilisateur

Teltonika

Teltonika TMU-10x Manuel utilisateur

Teltonika

Teltonika 3.5G Manuel utilisateur

Teltonika

Teltonika ModemCOM Manuel utilisateur

Teltonika

Teltonika ModemPCI G10 Manuel utilisateur

Teltonika

Teltonika ModemUSB TMU-10 Series Manuel utilisateur

Teltonika

Teltonika U3G150 Manuel utilisateur

Teltonika

Teltonika CM100 Manuel utilisateur

Teltonika

Teltonika TMU-102 Manuel utilisateur

Teltonika

Teltonika ModemPCI G10 Manuel utilisateur

Teltonika

Teltonika CM1100 Manuel utilisateur

Teltonika

Teltonika T-ModemUSB TMU-100 Manuel utilisateur

Teltonika

Teltonika ModemPCI G10 Manuel utilisateur

Teltonika

Teltonika VoiceFax Manuel utilisateur

Teltonika

Teltonika T-Wireless COM Manuel utilisateur

Teltonika

Teltonika U3G150 Manuel utilisateur

Teltonika

Teltonika UM6225 Manuel utilisateur

Teltonika

Teltonika ModemCOM/G10 Manuel utilisateur

Teltonika

Teltonika E10 Manuel utilisateur

Teltonika

Teltonika Maxview MXL066 Instructions de montage

Teltonika

Teltonika UM1000 Manuel utilisateur

Teltonika

Teltonika GM6225 Manuel utilisateur

Manuels Modem populaires d'autres marques

Davicom

Davicom DM562AP Manuel utilisateur

EpiValley

EpiValley TATA indicom SXC-1080 Manuel utilisateur

Zte

Zte WiMAX Manuel utilisateur

Intelimax

Intelimax MA-2060 Manuel utilisateur

SMC Networks

SMC Networks D3CM1604V Manuel d'utilisation et d'entretien

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manuel utilisateur

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manuel utilisateur

Samsung

Samsung AceLink SAM-335A Manuel utilisateur

Enfora

Enfora Enabler-G Guide de configuration rapide

iRZ

iRZ ATM2-232 Manuel utilisateur

Zhone

Zhone 6310 Manuel utilisateur

Paradyne

Paradyne Hotwire 7976 Manuel utilisateur

US Robotics

US Robotics 3453C Manuel utilisateur

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuel utilisateur

Zte

Zte MF823 Manuel utilisateur

Four-Faith

Four-Faith F1403 Manuel utilisateur

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manuel utilisateur

Gemtek

Gemtek WiMAX WIXFBR-103 Manuel utilisateur