Telematrix 2802MWD Manuel utilisateur
2802MWD
2 LINE -10 MEMORY
INSTALLATION
AND USER GUIDE
?Copyright TeleMatrix Inc. 2000
®
COMPLIANCE AND SAFETY
As specified by FCC regulation, we are required to inform you of specific governmental and
compliance regulatory requirements, safety notices, safety instructions and other informative
information. TeleMatrix, Inc. provides this information in a separate manual. We pack the
separate Compliance and Safety Manual within each outer box or product box when shipped.
Prior to reading this operation manual and prior to setting up your telephone, please refer to
the Compliance and Safety Manual.
If the Compliance and Safety Manual is not immediately available. Please obtain a free copy by
calling our Priority Care Department (phone number 1-800-462-9446) or by downloading a copy
on our Internet (web site address www.telematrixusa.com).
Features ...........................................………..……………………………………................................... 1
Controls ...........................................................................………………………………………………..2
Switch Settings .....................................….......................……………………………………………...... 4
Installation .....................................................................……………………………………………........ 5
Wall Mounting .....................................….......................……………………………………………........ 7
Programming Speed Dial Memory .................................……………………………………………....... 8
Operation ........................................................................……………………………………………..... 11
Care and Maintenance ..................................................……………………………………………....... 14
Service …………………………………………………..……………………………………….………… 15
Warranty .......................................................................……………………………………………....... 16
CONTENTS
FEATURES
?? TwoLine
?? Convenient Data Port
?? 10 Single Button Memory Locations With Secure Programming
?? Tone Dialing
?? Speaker Key
?? Conference Key
?? Mute Key
?? Handset Volume Control
?? TouchLite™ Message Waiting Retrieval
?? NEON/LED Message Waiting Switch
?? Store Key (submerged))
?? Storable Flash Function (600 mS) (submerged)
?? Storable Pause Function (3.6 seconds) (submerged)
?? HI/LOW Ringer Volume Control Switch
?? Desk or Wall Mountable
?? Fully Modular, Easy To Install
1
CONTROLS
2
LINE
2L
OW
HI
H
ANDSE
T
LOWHI
LINE1
(1)
(2)
(3)
(4)
(5)
(10)
(6)
(7)
(8)
(9)
(12)
(13)
(16)
(15)
(11)
(14)
LED
24V
L2
L1
48V
DEFINITION OF CONTROLS
1. Handset ..........…………..………….........…... Hearing aid compatible, low profile styling.
2. Ringer Controls ………………….……………. Adjusts the volume of the ringers to HI/LOW setting.
3. Handset Clip …………………………………... Retains the handset when the phone is wall mounted.
4. Handset Jack ……………………………….… Modular receptacle where handset cord plugs into the base unit.
5. Dial Pad ………………………………….…….. Large keys used for dialing.
6. Conference Key ……………………………… Used for conference calling.
7. Speaker Key …………………………………… Used to activate speaker
8. Mute Key ……………………………………….. Used to mute speaker key and handset
9. Handset Volume Control ……………….…….. Controls the loudness of the receiver volume when pressed.
10. Message Waiting TouchLite™ Key ………….. Used to call voice mail to retrieve messages.
11. Pause Key ……………………………………... (Submerged Key) Used to program a 3.6 second pause in memory.
12. Flash Key …………………………………….… (Submerged Key) Used to provide a 600 mS line break to access PBX/Centrex.
13. Feature Access Keys …………………………. 10 Programmable memory locations for frequently dialed phone numbers and access codes.
14. Data Port ……………………………………….. Used to connect a computer modem, fax machine, or answering device.
15. Message Waiting Selector Switch ………….. Select optional 90VDC or Low voltage LED Message Waiting.
16. Store Key ………………………………………. (Submerged Key) Used to program information for speed dialing.
3
SWITCH SETTINGS
There are installer selectable switches located on the bottom base underneath a protective plastic overlay. These switches are
hidden behind a plastic cover for security. To locate, remove the plastic covers using a sharp pointer or paper clip as shown.
Message Waiting Selector
The 2802MWD can support 90VDC neon or low-voltage LED message waiting
systems. Simply slide the switch to the desired position that is compatible with
your PBX messaging system.
Note: the phone is factory preset to the “Neon” setting.
4
Line Voltage Selectors
The 2802MWD is designed to operate behind PBX telephone systems rated
between 24 volts and 48 volts. There are line voltage selector switches that
must be set according to the PBX system rating that the phone will be installed.
There are two (2) switches, the first for Line 1 and the other for Line 2. Each
switch has three (3) setting options. They are: “24V/48V/OFF”. Set the
switches by simply sliding to the appropriate setting. The ”OFF” setting is used
to turn off the line if a line appearance is not wired to the telephone. (figure 6)
Note: the factory default is set to the “24V” setting.
LED
24V
L2
L1
NEON
48V OFF
Figure 6
Figure 5
LED
24V
L2
L1
NEON
48V OFF
INSTALLATION
Parts Check List
The following parts are included in this package:
1. 15’ modular telephone line cord.
2. Modular coiled handset cord.
3. Base unit
4. Handset
Caution
?? Never install telephone wiring during a lightning storm.
?? Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
?? Never touch uninstalled telephone wires or terminals unless the telephone line has been disconnected at the network interface.
?? Use caution when installing or modifying telephone lines.
5
(1)
(2)
(3)
(4)
Parts not included wall mount wedge. Call customer service for wall mount wedge.
Figure 3
Connecting The Handset Cord
A 10’ modular coil handset cord is provided.
To install, simply plug one end of the handset
cord into the modular jack on the handset.
The remaining end of the handset cord plugs
into the jack labeled “Handset” located on the
left side of the base unit.
(figure 3)
INSTALLATION
Connecting The Line Cord
A 15’ modular line cord is provided.
To install, simply plug one end of the line
cord into the modular jack located on the
back of the base unit. The remaining end of
the line cord plugs into the wall jack.
(figure 4)
Figure 4
6
L
I
N
E
2
L
O
W
H
I
H
A
N
D
S
E
T
L
O
W
H
I
L
I
N
E
1
JACK
LINE
WALL MOUNTING
Wall Mounting Your 2802MWD
The 2802MWDwas designed to be conveniently wall mounted.
There is no additional hardware required. Follow these easy
steps:
1. The handset retaining clip must be engaged to secure the
handset when hanging up. To engage the clip, unsnap the
clip, rotate the clip 180º and then snap the clip into place.
(figure 7)
2. Plug one end of a short line cord (not included) into the line
jack on the back of the Marquis base unit. Plug the remaining
end of the short line cord into the wall jack. Next, guide the
phone onto the studs of the wall jack. Pull down firmly until you
feel it snap into place. The unit is now wall mounted. (figure 8)
Figure 7
7
1. UNSNAP
2. ROTATE 180 .
3. SNAP INTO PLACE.
Figure 8
WEDGE
2.SNAP INTO PLACE.
TABS.
1.PRESS THE RELEASE
MOUNTING
Autres manuels pour 2802MWD
1
Table des matières
Autres manuels Telematrix Téléphone
Telematrix
Telematrix Spectrum Plus SP750 Mode d'emploi
Telematrix
Telematrix DECT MWD5 Manuel utilisateur
Telematrix
Telematrix Marquis 2802MWS Manuel utilisateur
Telematrix
Telematrix Marquis 3000MW10 Manuel utilisateur
Telematrix
Telematrix SIP 9600IP Manuel utilisateur
Telematrix
Telematrix MARQUIS 3300 Series Manuel utilisateur
Telematrix
Telematrix marquis 3000MW5 Manuel utilisateur
Telematrix
Telematrix Marquis 3000MWB Manuel utilisateur
Telematrix
Telematrix Spectrum Plus SP750 Manuel utilisateur
Telematrix
Telematrix Spectrum Plus SP550 Manuel utilisateur
Telematrix
Telematrix 3302TRM Manuel utilisateur
Telematrix
Telematrix Marquis 2800MW5 Manuel utilisateur
Telematrix
Telematrix Marquis EUROMW5 Manuel utilisateur
Telematrix
Telematrix 3002MWD5 Manuel utilisateur
Telematrix
Telematrix Marquis 2800MW10 Manuel utilisateur
Telematrix
Telematrix Spectrum Plus LP550 Manuel utilisateur
Telematrix
Telematrix Spectrum Plus LP550 Manuel utilisateur
Telematrix
Telematrix Spectrum Plus SP550 Mode d'emploi
Telematrix
Telematrix marquis 3000MWD Manuel utilisateur
Telematrix
Telematrix 2802MWD Manuel utilisateur
