Teledyne T3MIL50 Manuel utilisateur

T3MIL50 & T3MIL50X

D.C. Milli-Ohm Meters

User Manual

This manual contains proprietary information, which is protected by

photocopied, reproduced or translated to another language without

prior written consent of the Teledyne LeCroy company.

The information in this manual was correct at the time of printing.

However, Teledyne LeCroy continues to improve products and

reserves the right to change specifications, equipment, and

maintenance procedures at any time without notice.

Table of Contents

SAFETY INSTRUCTIONS ......................................................5

Safety Symbols...................................................................................... 5

Safety Guidelines.................................................................................. 6

GETTING STARTED..............................................................9

T3MIL50/50X Characteristics ............................................................ 10

Key Features........................................................................................ 12

Model Lineup...................................................................................... 13

Front Panel Overview ......................................................................... 14

TFT-LCD Overview.............................................................................. 18

Rear Panel Overview........................................................................... 20

Set Up.................................................................................................. 22

MEASUREMENT................................................................27

Resistance Measurement................................................................... 28

Compare Function.............................................................................. 38

Binning Function ................................................................................ 43

Temperature Measurement................................................................ 47

Temperature Compensation .............................................................. 49

Temperature Conversion.................................................................... 52

Measurement Settings ....................................................................... 56

System Settings .................................................................................. 63

HANDLER/SCAN INTERFACE.............................................72

Handler Overview............................................................................... 73

Pin Definitions for the Handler Interface.......................................... 75

Scan Overview .................................................................................... 77

Configure Interface............................................................................. 84

SAVE/RECALL ....................................................................89

COMMAND OVERVIEW .....................................................92

Command Syntax................................................................................ 92

Command List .................................................................................... 95

T3MIL Series User Manual

General Commands............................................................................98

Compare Commands .......................................................................102

Binning Commands..........................................................................107

Temperature Compensate Commands............................................112

Temperature Conversion Commands..............................................113

Temperature Commands..................................................................115

Scan Commands...............................................................................116

Source Commands ...........................................................................121

Meas. Setup Commands..................................................................122

System Commands...........................................................................127

Memory Commands.........................................................................132

Status Commands ............................................................................134

IEEE 488.2 Common Commands ....................................................135

Status system....................................................................................138

FAQ.................................................................................139

APPENDIX.......................................................................140

Function Selection Combinations....................................................141

Temperature Measurement..............................................................142

Specifications....................................................................................145

Dimensions.......................................................................................148

CERTIFICATIONS ...........................................................149

EMC Compliance ..............................................................................149

Safety Compliance ............................................................................151

Environmental Compliance..............................................................151

RESTRICTION OF HAZARDOUS SUBSTANCES (RoHS)..............152

SAFETY INSTRUCTIONS

This chapter contains important safety instructions that you must follow

when operating the T3MIL50/50X or when keeping it in storage. Read the

following before any operation to ensure your safety and to keep the

T3MIL50/50X in the best possible condition.

Safety Symbols

These safety symbols may appear in this manual or on the T3MIL50/50X.

WARNING

Warning: Identifies conditions or practices that could

result in injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that could

result in damage to the instrument or to other properties.

DANGER High Voltage

Attention Refer to the Manual

Protective Conductor Terminal

Earth (ground) Terminal

Do not dispose electronic equipment as unsorted

municipal waste. Please use a separate collection facility

or contact the supplier from which this instrument was

purchased.

T3MIL Series User Manual

Safety Guidelines

General Guideline

CAUTION

Do not place any heavy objects on the instrument.

Avoid severe impact or rough handling that leads to

damaging the instrument.

Do not discharge static electricity to the instrument.

Use only mating connectors, not bare wires, for the

terminals.

Do not disassemble the instrument unless you are

qualified as service personnel.

(Note) EN 61010-1:2010 specifies the measurement categories and

their requirements as follows. The T3MIL50/50X doesn’t fall

under category II, III or IV.

Measurement category IV is for measurements performed at the

source of low-voltage installation.

Measurement category III is for measurements performed in the

building installation.

Measurement category II is for measurements performed on the

circuits directly connected to the low voltage installation.

Power Supply

WARNING

AC Input voltage: 100 - 240 V AC, 50 - 60Hz, 25VA

The power supply voltage should not fluctuate more

than 10%.

Connect the protective grounding conductor of the AC

power cord to an earth ground, to avoid electrical

shock.

Cleaning the

T3MIL50/50X

Disconnect the power cord before cleaning.

Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid into the

instrument.

Do not use chemicals or cleaners containing harsh

material such as benzene, toluene, xylene, and acetone.

Operation

Environment

Location: Indoor, no direct sunlight, dust free, almost

non-conductive pollution (Note below)

Temperature Range: 0~35°C, Relative Humidity:

<80%RH; >35°C, Relative Humidity: <70%RH

Altitude: < 2000m

Operating Environment: 0°C to 40°C (operation)

Pollution Degree 2

SAFETY INSTRUCTIONS

(Note) EN 61010-1:2010 specifies the pollution degrees and their

requirements as follows. The T3MIL50/50X falls under degree 2.

Pollution refers to “addition of foreign matter, solid, liquid, or

gaseous (ionized gases), that may produce a reduction of dielectric

strength or surface resistivity”.

Pollution degree 1: No pollution or only dry, non-conductive pollution

occurs. The pollution has no influence.

Pollution degree 2: Normally only non-conductive pollution occurs.

Occasionally, however, a temporary conductivity caused by

condensation must be expected.

Pollution degree 3: Conductive pollution occurs, or dry,

non-conductive pollution occurs which becomes conductive due to

condensation which is expected. In such conditions, equipment is

normally protected against exposure to direct sunlight, precipitation,

and full wind pressure, but neither temperature nor humidity is

controlled.

Storage

Environment

Location: Indoor

Storage Conditions: −10°C to 70°C

Temperature Range: 0~35°C, Relative Humidity:

<90%RH; >35°C, Relative Humidity: < 80%RH

Disposal

Do not dispose this instrument as unsorted municipal

waste. Please use a separate collection facility or contact

the supplier from which this instrument was purchased.

Please make sure discarded electrical waste is properly

recycled to reduce environmental impact.

T3MIL Series User Manual

Power cord for the United Kingdom

When using the instrument in the United Kingdom, make sure the power

cord meets the following safety instructions.

NOTE: This lead / appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in accordance with the

following code:

Green/ Yellow:

Earth

Blue:

Neutral

Brown:

Live (Phase)

As the colours of the wires in main leads may not correspond with the

coloured marking identified in your plug/appliance, proceed as follows:

The wire which is coloured Green & Yellow must be connected to the Earth

terminal marked with either the letter E, the earth symbol or coloured

Green/Green & Yellow.

The wire which is coloured Blue must be connected to the terminal which is

marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the terminal marked

with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment or contact

the supplier.

This cable/appliance should be protected by a suitably rated and approved

HBC mains fuse: refer to the rating information on the equipment and/or

user instructions for details. As a guide, a cable of 0.75mm2should be

protected by a 3A or 5A fuse. Larger conductors would normally require 13A

types, depending on the connection method used.

Any exposed wiring from a cable, plug or connection that is engaged in a live

socket is extremely hazardous. If a cable or plug is deemed hazardous, turn

off the mains power and remove the cable, any fuses and fuse assemblies. All

hazardous wiring must be immediately destroyed and replaced in accordance

to the above standard.

GETTING STARTED

This chapter describes the T3MIL50/50X, including its main features as well

as its front and rear panels. After going through the panel overview, follow the

Power-up sequence before attempting to use the instrument.

Please note the information in this manual was correct at the time of printing.

However as Teledyne LeCroy continues to improve its products, changes can

occur at any time without notice. Please see the Teledyne LeCroy website for

the latest information and content.

T3MIL50/50X Characteristics ............................................................ 10

Key Features........................................................................................ 12

Model Lineup...................................................................................... 13

Front Panel Overview ......................................................................... 14

TFT-LCD Overview.............................................................................. 18

Rear Panel Overview........................................................................... 20

Set Up.................................................................................................. 22

Tilt Stand ................................................................................................................ 22

Power Up................................................................................................................ 23

4 Wire Kelvin Connection ...................................................................................... 24

Zeroing (Relative Function)................................................................................... 25

T3MIL Series User Manual

T3MIL50/50X Characteristics

T3MIL50 and T3MIL50X are modern high precision programmable DC

Milli-ohm meters suitable for low resistance measurements of switches, relays,

connectors, PCB tracks and a variety of other devices. The meters feature a

color TFT-LCD screen with easy-to-read measurement results. With the

easy-to-use features, superior performance and automatic test interfaces, these

meters are dependable instruments for resistance measurements.

Easy to Use

Features

Each test function on the T3MIL50/50X can be easily

activated by pressing a single front panel key. All the

settings and measurement results are displayed and set on

the TFT-LCD panel at the same time making each

function naturally intuitive to use.

Each primary and secondary measurement result is

displayed prominently on the display along with any

corresponding settings. Sequential measurement results,

such as those from the scan or binning function, are

tabulated in an intuitive and easy-to-read format.

In addition, the meters can recall previously used settings

upon startup, allowing the meter to be ready the next

time it is used in a matter of moments. The meters can

also save or recall up to 20 sets of function settings.

Performance

The T3MIL50/50X has nine selectable measurement

ranges from 5mΩ to 5MΩ, a constant current source of

1uA to 1A, an accuracy of up to 0.05%, a 0.1uΩ

resolution and performs measurements using four wire

Kelvin connections for accurate, consistent

measurements.

The ability to choose between high accuracy

measurements at 10 samples/sec (full scale at 50000

counts) or high speed measurements at 60 samples/sec

(full scale at 50000 counts), allows the T3MIL50/50X the

flexibility to fulfill a number of different measurement

roles.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Teledyne Instrument de mesure

Teledyne

Teledyne 3000TA Guide d'installation et d'utilisation

Teledyne

Teledyne 430 Manuel utilisateur

Teledyne

Teledyne First Responder CG Mode d’emploi

Teledyne

Teledyne HVG-2020A Manuel utilisateur

Teledyne

Teledyne 235 Manuel utilisateur

Teledyne

Teledyne 2010B Manuel utilisateur

Teledyne

Teledyne 275R Manuel utilisateur

Teledyne

Teledyne GMI PS200 Manuel utilisateur

Teledyne

Teledyne ADFM Pro20 Mode d'emploi

Teledyne

Teledyne T100 Manuel utilisateur

Teledyne

Teledyne 212R Manuel utilisateur

Teledyne

Teledyne TED 191 Manuel utilisateur

Teledyne

Teledyne 2000A-EU Manuel utilisateur

Teledyne

Teledyne PEM-9004 Manuel utilisateur

Teledyne

Teledyne HFM-301 Manuel utilisateur

Teledyne

Teledyne T200U Instructions d'installation et d'utilisation

Teledyne

Teledyne 200A Manuel utilisateur

Teledyne

Teledyne T102 Manuel utilisateur

Teledyne

Teledyne HASTINGS 4/6 Manuel utilisateur

Teledyne

Teledyne Mixchek Manuel utilisateur

Teledyne

Teledyne 6600 Manuel utilisateur

Teledyne

Teledyne 730 Bubbler Manuel utilisateur

Teledyne

Teledyne 6750 Manuel utilisateur

Teledyne

Teledyne IR7000 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur