Telect LTX Manuel utilisateur

LTX

Patch and Splice Panel

1.509.926.6000 :: telect.com

LTX Patch and Splice Panel

Fiber :: Install guide

This page intentionally left blank.

1.509.926.6000 :: telect.com 3

LTX Patch and Splice Panel

Fiber :: Install guide

Table of Contents

1 Introduction...................................................................................................................................................... 5

1.1 Specications .......................................................................................................................................... 5

1.2 About this Guide...................................................................................................................................... 6

1.3 Terminology............................................................................................................................................. 6

1.4 LTX Panel Overview ................................................................................................................................ 7

2 Installation Considerations............................................................................................................................... 9

2.1 Inspection ............................................................................................................................................... 9

2.2 Unpacking............................................................................................................................................... 9

2.2.1 Contents .................................................................................................................................... 10

2.3 Installation Guidelines .......................................................................................................................... 10

2.4 Location and Space.............................................................................................................................. 10

2.5 Tools and Equipment ............................................................................................................................ 10

3 LTX Patch and Splice Panel Installation .........................................................................................................11

3.1 LTX Panel Component Installation..........................................................................................................11

3.1.1 Install Entry/Exit Arcs ...................................................................................................................11

3.1.2 Install Routing Spools...................................................................................................................11

3.1.3 Install Splice Trays....................................................................................................................... 12

3.1.4 Install Tray Platform ..................................................................................................................... 12

3.1.5 Install Cable Clamp Bracket ........................................................................................................ 13

3.1.6 Install Cable Clamp ..................................................................................................................... 13

3.1.7 Install Central Strength Member Holder...................................................................................... 13

3.1.8 Install Adapter Patch Plate .......................................................................................................... 14

3.1.9 Install Panel Doors ...................................................................................................................... 14

3.1.10 Install Designation Labels ........................................................................................................... 15

3.1.11 Install Mounting Brackets to the LTX Panel ................................................................................. 15

3.2 Install and Ground the LTX Panel to the Rack ....................................................................................... 16

4 LTX Patch and Splice Panel Cable and Fiber Installation and Routing.......................................................... 17

4.1 Cable Installation and Routing............................................................................................................... 17

4.1.1 IFC Cable Installation and Routing.............................................................................................. 17

4.1.2 Install IFC in the Cable Clamp..................................................................................................... 18

4.1.3 Route Protected 12-Strand Ribbon Fiber in LTX Panel Slack Storage Area ................................18

4.1.4 Install Ribbon Fibers in the Splice Tray........................................................................................ 19

4.1.5 Install Pigtail Fiber Connectors.................................................................................................... 20

4.1.6 Route Pigtail Fibers in the Splice Tray ......................................................................................... 21

4.2 Splice and Route Fibers ........................................................................................................................ 22

4.3 Connect Fiber Jumpers at the Patch Panel ........................................................................................... 22

5 Service........................................................................................................................................................... 24

5.1 Owner Maintenance............................................................................................................................... 24

5.1.1 High Insertion Loss and the Importance of Cleaning Connectors and Adapters......................... 24

5.2 Technical Support .................................................................................................................................. 25

5.3 In-Warranty Service............................................................................................................................... 25

5.4 Out-of-Warranty Service........................................................................................................................ 25

5.5 Repacking for Shipment......................................................................................................................... 25

1.509.926.6000 :: telect.com

LTX Patch and Splice Panel

Fiber :: Install guide

List of Figures

Figure 1-1 LTX Patch and Splice Panel with SC Adapters ................................................................................... 5

Figure 1-2 LTX Patch and Splice Panel Overview - Front and Rear Views ............................................................ 7

Figure 3-1 Install Entry/Exit Arcs...........................................................................................................................11

Figure 3-2 Install Routing Spools..........................................................................................................................11

Figure 3-3 Install Splice Trays .............................................................................................................................. 12

Figure 3-4 Install Tray Platform ............................................................................................................................ 12

Figure 3-5 Install Cable Clamp Bracket ............................................................................................................... 13

Figure 3-6 Install Cable Clamp ............................................................................................................................ 13

Figure 3-7 Central Stength Member Holder Installation....................................................................................... 13

Figure 3-8 Install Adapter Patch Plate.................................................................................................................. 14

Figure 3-9 Door Installation ................................................................................................................................. 14

Figure 3-10 Install Designation Labels................................................................................................................... 15

Figure 3-11 Install Mounting Brackets on LTX Panel.............................................................................................. 15

Figure 3-12 Install and Ground LTX Panel to the Rack .......................................................................................... 16

Figure 4-1 Secure IFC Cabling to the LTX Panel ................................................................................................. 17

Figure 4-2 Route Protected 2-Strand Ribbon Fiber through LTX Panel Slack Storage Area................................ 17

Figure 4-3 Install Ribbon Fibers in the Splice Tray............................................................................................... 19

Figure 4-4 Pigtail Fiber Connectors ..................................................................................................................... 20

Figure 4-5 Install Pigtail Fibers Connectors ......................................................................................................... 20

Figure 4-6 Route Pigtail Fibers in the Splice Tray ................................................................................................ 21

Figure 4-7 Connect Fiber Jumpers to the Patch Panel ........................................................................................ 23

1.509.926.6000 :: telect.com 5

LTX Patch and Splice Panel

Fiber :: Install guide

Telect's LTX Patch and Splice Panel consolidates network ber

splice, patching, and routing requirements in a 4RU panel.

The LTX panel accommodates up to 288 fiber terminations and

houses eight splice trays.

Figure 1-1 - LTX Patch and Splice Panel with SC Adapters

Dimensions and Weights

Dimensions 7"H x 17"W x 17"D

Weight 12 lbs

Mechanical

Connector type SC/UPC, SC/APC, LC/APC, LC/UPC, MPO/MTP

Access Front and Rear

Capacity 288 port 4RU

Splicing Mass Fusion / Stranded

Panel mounting 19" or 23" with ETSI, EIA, or WECO spacing

Adapter access Patch Panel

Material Aluminum/Steel

Compliance NEBS, ETSI, Zone 4 Seismic reliability

Environmental

Temperature range -5°C to 55°C

Humidity 90%, non-condensing

1.1 Specications

1 Introduction

Front View

Rear View

144 SC Terminations

shown

1.509.926.6000 :: telect.com

LTX Patch and Splice Panel

Fiber :: Install guide

This manual provides a comprehensive overview of and installation guidelines for the LTX Patch and Splice Panel. While care has been taken

to dene all necessary information, complete details may not be covered. If you have any questions, contact Telect Technical Support at

suppor[email protected] or call 1.509.926.6000.

Throughout this guide, relevant and crucial information is displayed in the form of Notes, Alerts, Cautions, and Warnings. These notications

are prominently displayed and their importance is indicated as follows:

NOTE: General information the user should pay special attention to.

Alert! Important information and/or instructions the user should adhere to.

CAUTION! Indicates a hazardous situation, which if not avoided could result in minor or moderate injury.

WARNING: Indicates a potentially hazardous situation which if not avoided could result in death or serious injury.

Telect assumes no liability from the application or use of these products. Neither does Telect convey any license under its patent rights of

others. This document and the products described herein are subject to change without notice.

1.2 About this Guide

1.3 Terminology

Acronym/Abbreviation Term

IF IntraFacility Fiber

IFC IntraFacility Cable

LC Local Connector

MPO Multi-ber Push-On optical ber module interface type

NE Network Element

NEBS Network Equipment Building System (telecommunications product safety equipment rating standard)

PC Physical Contact ber optic connector (single or multimode)

SC Standard Connector

TIA Telecommunications Industry Association

TIA/EIA-568 B.3 Telecommunication standards for commercial cabling

TUV Technical Inspection Association (global product certication compliance marking)

UL Underwriter Laboratories (electrical standards)

UPC Ultra Physical Contact ber optic connector (single or multimode)

The following list of acronyms and abbreviations are used throughout this manual.

1.509.926.6000 :: telect.com 7

LTX Patch and Splice Panel

Fiber :: Install guide

Telect's LTX Patch and Splice Panel consolidates network ber

splice, patching, and routing requirements in a 4RU panel. The

LTX panel accommodates

• Up to 288 fiber terminations

• Stacked splice trays, each housing 36 splice sleeve

holders

• Velcro bands that secure trays inside the panel

• Routing spools to manage slack cable routing

• Panel mounted cable clamp for incoming cable control

• Convenient spring-hinged removable front and rear doors

• Designation labels on front and rear doors

Interconnect and cross-connect cabling enter the LTX panel at rear

corner locations guided over rubber edge protectors. Slack storage

area in the rear of the panel routes IntraFacility Fibers (IF) through

the panel to splice trays in the center of the panel. After splicing,

pigtail bers connect to patch plate mounted connectors at the rear

of the panel and ber jumpers connect to adapters at the front.

LTX Patch and Splice Panel patch plates can accommodate:

• SC/UPC, SC/APC, LC/APC, LC/UPC are available in patch

plates with 6 or 8 adapters

• LC/SC available in patch plates with 12 adapters

• LC/UPC and LC/APC available in patch plates with 24

adapters

• MPO/MTP feed through patch plates available with 6 or 8

adapters

In addition,Telect offers a special factory-congured integrated

4RU patch plate panel with up to 288 terminations (requires use of

LC duplex adapters).

Adapters are also offered in multimode versions. All adapters

include dust covers. Most patch plates are available in white or

black.

1.4 LTX Panel Overview

Figure 1-2 - LTX Patch and Splice Panel Overview

- Front and Rear Views

LTX Patch and Splice Panel, Front View

(144 terminations shown)

Front Door

Rear Door

Routing Spool

Slack

Storage

Area

Fiber

Jumper

Entry

Area

Designation Card

(Front Side)

Patch Plate with Adapters Cable

Clamp

Designation Card

(Rear Side)

Cable

Clamp

Arc

Patch

Plate with

Connectors

Arc

LTX Patch and Splice Panel, Rear View

(144 terminations shown)

Arc

Fiber

Jumper

Entry

Area

Arc Arc

Arc

Cable

Entry

Area Arc Stacked

Splice

Trays

Cable

Entry

Area

Arc

Velcro

Tie

1.509.926.6000 :: telect.com

LTX Patch and Splice Panel

Fiber :: Install guide

This page intentionally left blank.

1.509.926.6000 :: telect.com 9

LTX Patch and Splice Panel

Fiber :: Install guide

2 Installation Considerations

WARNING: Verify all connections meet requirements specied in local electric codes or operating company guidelines before

supplying power. Unit must be protected by a listed circuit breaker or branch-rated fuse sufficient to interrupt power levels.

WARNING: Use of fully insulated tools is required when working with any AC or DC circuits.

WARNING: Fiber cables transmit invisible infrared light. To avoid eye damage or blindness, never look directly into bers or

connectors.

ALERT! This product must be installed and maintained only by qualied technicians.

ALERT! Install this system according to company requirements. It is recommended to install the system in a Restricted Access

Location (RAL) where access is limited through use of tool (i.e., lock and key) or other means of security and be controlled by the

authority responsible for the location.

ALERT! Prior to panel installation, ensure there is enough space in front and rear to access cabling.

ALERT! Only use components and crimping tools approved by agencies or certifying bodies recognized in your country or region,

such as Underwriter’s Laboratories (UL), TUV, etc.

ALERT! Do not stand on ber or ber cables.

CAUTION! These instructions presume you have veried that the Telect equipment being installed is compatible with the rest of

the system including power, ground, circuit protection, signal characteristics, equipment from other vendors, and local codes or

ordinances.

When you receive the equipment, carefully unpack it and compare it to the packaging list. Please report any defective or missing parts to

Telect Quality at [email protected] or call 1.509.926.6000. Keep all documentation that comes with your shipment.

Please read and understand all instructions before starting installation. If you have any questions, contact Telect Technical Support at

suppor[email protected] or call 1.509.926.6000.

The panel is wrapped with a high-strength plastic. Exercise care when unpacking and setting the equipment in place.

Telect is not liable for transit damage. If the product is damaged, please report it to the carrier and contact Telect Quality.

2.1 Inspection

2.2 Unpacking

The LTX Patch and Splice Panel is 7"H x 17"W x 17"D, and weighs 12 lbs. The panel comes pre-assembled as one unit.

Upon receipt of your order, carefully unpack it and compare it with the packing list and the order placed. While items described below are a

comprehensive list that includes the LTX panel, splice trays with splice sleeves, spools, brackets, and doors, the contents of your order may

vary.

1.509.926.6000 :: telect.com

LTX Patch and Splice Panel

Fiber :: Install guide

• LTX Patch and Splice Panel

• Tray platform

• Splice trays

• Splice sleeve holders

• Arcs (edge protectors)

• Velcro bands

• Routing spools

2.2.1 Contents

• Removable doors (spring-hinged swing down)

• Designation labels (front and rear)

• Cable clamp bracket

• Cable clamp with bushing sleeves

• Mounting brackets (to mount to 19"or 23"rack)

• Installation guide

2.3 Installation Guidelines

• Elevated Operating Ambient Temperature - If installed in a closed or multi-unit rack assembly, the operating ambient temperature

of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an

environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.

• Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven

mechanical loading.

• Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply

connections other than direct connections to the branch circuit (e.g. use of power strips).

2.4 Location and Space

The LTX Patch and Splice Panel requires space in the front and rear for access to patching, splicing, and cabling. Leave as much side

clearance for tray and panel removal and worker access as required by your application or local regulations. Plan the input/output, upward/

downward (cable feed) layout of each panel and its position in the rack before beginning LTX panel installation.

LTX panels adapt to standard 19"or 23" ETSI racks with EIA, ETSI, and WECO spacing and nominal 3¼" extensions beyond the front rack

ange.

No special tools required.

2.5 Tools and Equipment

Autres manuels pour LTX

Table des matières

Autres manuels Telect Panneau de contrôle

Telect

Telect GMT Series Manuel utilisateur

Telect

Telect LCX Series Manuel utilisateur

Telect

Telect LCX Series Manuel utilisateur

Telect

Telect LTX Manuel utilisateur

Telect

Telect 009-8004-0208 Manuel utilisateur

Telect

Telect 009-8005-3404H Manuel utilisateur

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques