Tektronix TriMode P7500 Series Manuel utilisateur

1 White Paper

P7500 TriMode™ Probe Deskew

Procedures

Overview

Deskew aligns signals to compensate for differing signal

delays from cables of different lengths. The oscilloscope

deskew feature applies deskew correction after it

completes each acquisition. The deskew values do not

affect logic triggering. Deskew has no affect on XY and

XYZ display formats. In order to perform deskew with

the P7500 Series probes, the Tektronix Deskew Fixture

(Part Number 067-1586-00) shown in Figure 1 is

required.

Step-by-Step Procedures

1. Connect the deskew fixture to a USB power source as shown in

Figure 2 with the other end of the USB cable plugged into the

oscilloscope.

2. Connect the probes to the oscilloscope.

Figure 1: Tektronix P7500 Deskew Fixture

Figure 2: Powering the Deskew Fixture

2 White Paper

P7500 TriMode™ Probe Deskew Procedures

3. Locate the solder box on the Deskew Fixture. Ensure that

the solder pins are in the middle of the solder box as shown

in the box in Figure 3

4. Solder the first of two P75TLRST solder tips to the solder

pins.

5. Push the pins through the solder box and rotate the P75TLRST

so that it is on the opposite side of the solder box as shown in

Figure 5. Secure the cable of the P75TLRST in the slot in the

clamp.

Figure 3: Location of the Solder Pins

Figure 4: P75TLRST Soldered to the Solder Pins

Figure 5: P75TLRST Secured in the Clamp

3 White Paper

P7500 TriMode™ Probe Deskew Procedures

6. Solder the second P75TLRST solder tip to the solder pins.

Make sure the second solder tip is inverted because the

polarities will need to match for proper deskew. The red band

on the solder tips should be located on the same side as

shown in Figure 6.

7. With the P75TLRST wire leads soldered on to the solder pins,

remove the solder pins from the solder box and install them in

the holes at the top of the Deskew Fixture shown in Figure 7.

The solder pin with the red band is inserted into the hole with

the “+” and the other solder pin is inserted into the hole with the

“-“.

Figure 7: Holes for the Solder Pins

Figure 6: Two P75TLRSTs Soldered to the Solder Pins

supersedes that in all previously published material. Specification and price change privileges reserved. TEKTRONIX and TEK are registered trademarks of

Tektronix, Inc.All other trade names referenced are the service marks, trademarks or registered trademarks of their respective companies.

03/09 JS/WWW 51W-24046-0

P7500 TriMode™ Probe Deskew Procedures

8. Close the clamp by pushing down on the lever to secure the Tip-

Clip assembly as shown in Figure 8. NOTE: To avoid

unnecessary wear on the clamp elastomer, leave the clamp in

the open position when not using the fixture.

9. The P75TLRST solder tips are positioned in the Deskew Fixture as

shown in Figure 9. Ensure the polarities of the wire leads are

attached to the correct connector. The red bands on the wires

should be located on the same side.

10. Reference your oscilloscope manual for detailed deskew adjustment

procedures.

Figure 8: Securing the Clamp on the Deskew Fixture

Figure 9: Two P75TLRSTs secured in the Deskew Fixture

Autres manuels pour TriMode P7500 Series

Table des matières

Autres manuels Tektronix Instrument de mesure

Tektronix

Tektronix TLA7AA1 Manuel utilisateur

Tektronix

Tektronix CSA7404 Manuel utilisateur

Tektronix

Tektronix TLA5202 Manuel utilisateur

Tektronix

Tektronix 4923 Manuel utilisateur

Tektronix

Tektronix H600 RFHawk Manuel utilisateur

Tektronix

Tektronix 492, 492P Manuel utilisateur

Tektronix

Tektronix TLA721 Manuel utilisateur

Tektronix

Tektronix 067 -0794-00 Manuel utilisateur

Tektronix

Tektronix P6207 Manuel utilisateur

Tektronix

Tektronix PA4000 Series Manuel utilisateur

Tektronix

Tektronix 1502C Manuel utilisateur

Tektronix

Tektronix RSA503A Manuel utilisateur

Tektronix

Tektronix 8001A Manuel utilisateur

Tektronix

Tektronix S-1 Manuel utilisateur

Tektronix

Tektronix 6 series Guide de l'utilisateur

Tektronix

Tektronix WVR8200 Manuel utilisateur

Tektronix

Tektronix RSA5100B series Instructions d'installation et d'entretien

Tektronix

Tektronix P7260 Manuel utilisateur

Tektronix

Tektronix DTM500 Series Manuel d'utilisation et d'entretien

Tektronix

Tektronix SPG8000A Manuel utilisateur

Tektronix

Tektronix KEITHLEY 2450 Manuel utilisateur

Tektronix

Tektronix Keithley 4200A-SCS Manuel utilisateur

Tektronix

Tektronix Keithley 4200A-SCS Manuel utilisateur

Tektronix

Tektronix TDP0500 Manuel

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur