Tekmar TekmarNet 553 Manuel utilisateur

tekmarNet®Thermostat 553

Installation & Operation Manual

553

04/13

Zoning

Replaces: New

1 of 48

A Watts Water Technologies Company

The tekmarNet®Thermostat 553

is a communicating touchscreen

thermostat designed to operate one

or two heating stages, one cooling

stage, a fan and relative humidity.

Introduction Energy Saving Features

Programmable Schedule

Zone Synchronization

Zone Post Purge

Warm Weather Shut Down

Cooling Interlock

Auto Heating Cycle

Temporary Hold

Away Scene Key

•

Additional Features

2 Auxiliary Sensor Inputs

tekmarNet®Communication

Compatible

Touchscreen Technology

Outdoor & Floor Temperature

Display

Backlight

Radiant Floor Heating & Cooling

Freeze Protection

Pump & Valve Exercising

Heat / Cool Priority

Air Group Master & Member

Network Schedule Master or

Member

Optimum Start

Scenes

Daylight Savings Time

Room Temperature Limiting

Relative Humidity Control

•

2 of 48

A Watts Water Technologies Company

Congratulations on the purchase of your new tekmar®thermostat.

This manual will step through the complete installation, programming and sequence

of operation for this control. At the back, there are tips for control and system

troubleshooting.

Getting Started

Table of Contents

Getting Started ...............................2

Installation ...........................................3

Caution............................................3

Preparation .....................................3

Removing The Thermostat Base....3

Mounting The Thermostat Base .....4

Thermostat Wiring ..........................4

Compatible Sensors .......................5

Testing the Thermostat Wiring........5

Mounting the Thermostat................6

Switch Settings....................................7

User Interface......................................8

Home Screen..................................8

Symbols Description.......................8

Programmable Settings.......................9

Programming Menus ......................9

Set Temp Menu........................10-13

Time Menu....................................14

Schedule Menu........................15-16

Display Menu ........................... 16-17

Scenes Menu................................17

Monitor Menu...........................18-21

Toolbox Menu ..........................21-23

Setup Menu............................. 24-30

Sequence of Operation......................31

Heat and Cool Applications ..........31

Heating Operation.........................31

Cooling Operation.........................33

Room Min and Max Limits ............33

Mode Operation............................34

Pump and Valve Operation...........34

Fan Operation...............................35

Relative Humidity Operation.........35

Air Group Operation......................37

Time Clock....................................37

Temperature Adjustment ..............38

Programmable Schedules ............39

Scenes (System Override)............40

Secondary Temperature Display..41

Access Levels...............................42

tekmarNet®Address .....................42

Cleaning the Thermostat ..............42

Troubleshooting .................................43

Error Messages ...................... 43-47

Technical Data ..............................47

Limited Warranty and Product

Return Procedure .........................48

3 of 48

A Watts Water Technologies Company

Preparation

tekmar or jeweller screwdriver

Phillips head screwdriver

•

Wire Stripper•

Tools Required

------------------------------------------------------

Materials Required

--------------------------------------------------

18 AWG LVT Solid Wire (Low

Voltage Connections)

•

Installation

Choose the placement of the thermostats early in the construction process to enable

proper wiring during rough-in.

Consider the following:

Interior Wall.

Keep dry. Avoid potential leakage onto the control.

Relative Humidity less than 90%. Non-condensing environment.

No exposure to extreme temperatures beyond 32-122°F (0-50°C).

No draft, direct sun, or other cause for inaccurate temperature readings.

Away from equipment, appliances, or other sources of electrical interference.

Easy access for wiring, viewing, and adjusting the display screen.

Approximately 5 feet (1.5 m) off the finished floor.

The maximum length of wire is 500 feet (150 m).

Strip wire to 3/8” (10 mm) for all terminal connections.

Use standard 8 conductor, 18 AWG wire.

•

Installation Location

-------------------------------------------------

Caution

Improper installation and operation of this control could result in damage to the equipment

and possibly even personal injury or death. It is your responsibility to ensure that this

control is safely installed according to all applicable codes and standards. This electronic

control is not intended for use as a primary limit control. Other controls that are intended

and certified as safety limits must be placed into the control circuit.

Removing The Thermostat Base

To remove the thermostat base:

Locate the tab on the bottom of the

thermostat.

Push the tab with either your thumb or with

a screwdriver.

Lift the thermostat front away from the

thermostat’s base.

•

4 of 48

A Watts Water Technologies Company

Thermostat Wiring

The thermostat can be wired in three different ways.

Stand Alone

- Similar to tekmarNet

4 wiring with tN4 wiring terminal not used. First

stage heating relay (Rh - W1) can be wired directly to switching relays.

tekmarNet®4- Allows the thermostat to be wired using 4 wires to a tN4 Wiring Center

or Zone Manager. The tN4 communication bus can also be daisy-chained to allow

multiple thermostats to be connected together without home running wires back to the

mechanical room.

tekmarNet®2- Allows the thermostat to be wired point-to-point using 2 wires to a tN2

Wiring Center, House Control, or Zone Manager. This allows easy wiring for retrofit

applications.

Application specific wiring diagrams are provided in the 553_A brochure.

Wall

Stud

Thermostat

Front

Thermostat

Base

If a gang box is not used:

Feed the wiring through the

large hole in the thermostat

base.

Mount the thermostat base

directly to the wall.

Use screws in the screw

holes to fasten the

thermostat to the wall. At

least one of the screws

should enter a wall stud or

similar rigid material.

Terminate wiring to the

wiring strip.

Push the thermostat front

onto the thermostat base.

•

Mounting The Thermostat Base

3 1/4”

(83 mm)

Thermostat

Front Thermostat

Base

Stud

Gang

Box

If a single gang box is used:

Feed the wiring through

the large hole of the

thermostat base.

Fasten the base of the

thermostat to the gang box.

Terminate wiring to the

wiring strip.

Push the thermostat front

onto the thermostat base.

•

5 of 48

A Watts Water Technologies Company

Testing tekmarNet®2 Wiring

------------------------------------------

Testing the Power

If the thermostat display turns on, this indicates that the thermostat is operating

correctly and there are no electrical issues. In the event that the display is off, or the

display is cycling on and off:

1. Remove the thermostat wiring cover.

2. Check to ensure that the tN2 wires on the thermostat are connected to a zone on a

House Control, Wiring Center, or Zone Manager.

3. Use an electrical meter to measure DC voltage between the tN2 terminals.

If the DC voltage is 0 V (dc) for at least 20 seconds, then there is an open or

short circuit in the tN2 wires.

If the DC voltage is 0 V (dc) for 10 seconds and then is 23 to 24 V (dc) for 5

seconds, this indicates the wiring is correct.

4. If the thermostat display is off, or is cycling on and off, move the thermostat to the

next available zone on the House Control, Wiring Center, or Zone Manager.

If the thermostat display remains permanently on, there may be a fault with the

previously tried zone on the House Control, Wiring Center, or Zone Manager.

If the thermostat display continues to be off, or is cycling on and off, there may

be a fault on the thermostat.

If a fault is suspected, contact your tekmar sales representative for assistance.

Testing tekmarNet®4 and Stand Alone Wiring

--------------------------

Testing the Power

1. Remove the front cover from the thermostat.

2. Use an electrical test meter to measure (ac) voltage between the R and C terminals.

The reading should be 24 V (ac) +/– 10%.

3. Install the front cover.

Testing the Relay Outputs

--------------------------------------------

The thermostat includes a User Test to check if the thermostat’s relays are operating

and that the thermostat is wired correctly to the HVAC equipment. The User Test setting

can be located in the Toolbox menu. Either Heat or Cool test can be selected.

Cancel button - Exits the user test and returns the Toolbox menu.

Hold button - Pauses the user test step for up to 5 minutes.

Next Item button - Advances the user test to the next test step.

•

Testing the Thermostat Wiring

Compatible Sensors

The thermostat is compatible with Indoor Sensor type 076, 077, 084, Slab Sensor

type 072, 073, 079, Outdoor Sensor type 070, Universal Sensor 082 and Duct Sensor

type 083.

6 of 48

A Watts Water Technologies Company

User Test Sequence

Heat Test Cool Test

Step Relay(s) Closed Step Relay(s) Closed

O RELAY ON Rc to G/O O RELAY OFF Rc to G/O

B RELAY OFF Rc to G/O B RELAY ON Rc to G/O

FAN ON Rc to G/O

(conventional)

Rc to ACC

(heat pump)

FAN ON Rc to G/O

(conventional)

Rc to ACC

(heat pump)

Y HEAT ON Rc to Y Y COOL ON Rc to Y

W2 HEAT ON Rc to ACC HUMIDIFY ON Rc to ACC

W HEAT Rh to W DEHUMIDIFY ON Rc to ACC

HUMIDIFY ON Rc to ACC

(heat and cool)

Rc to Y

(two-stage heat)

HRV ON Rc to ACC

DEHUMIDIFY ON Rc to ACC

HRV ON Rc to ACC

*availability of test step and additional relay closures based upon Setup menu settings.

Mounting the Thermostat

Push the thermostat front onto the

thermostat base. Installation is now

complete.

Thermostat

Front

Push

Thermostat

Base

7 of 48

A Watts Water Technologies Company

Switch Settings

Switch

Position

Action

ON LOCK ACCESS LEVEL

Thermostat is locally locked and the access level cannot be changed.

Set to Lock when installation has been completed.

OFF

UNLOCK ACCESS LEVEL

Thermostat is unlocked and the access level may be changed. Go to

the Toolbox menu to change the access level. Set to Unlock during

the installation process.

Note: tekmarNet®system controls include a Global Lock that locks all

connected thermostats. Set the tekmarNet

system control to unlock

to allow access level adjustment on all connected thermostats.

2ON

Not used

OFF

Not used

tekmarNet

Thermostat 553

Two Stage Heat, One Stage Cool, Fan

Mmm YYYY

Lot # 12345 Meets Class B: ICES & FCC Part 15

Power: tN2 or 24 V (ac) ±10% 1.8 VA

Relay: 24 V (ac) 2 A

Switch

Settings

www.tekmarcontrols.com

Designed and assembled in Canada

Lock

Unused

Unlock

Back of

Thermostat

8 of 48

A Watts Water Technologies Company

HEAT ON

Heat is turned on.

COOL ON

Cooling is turned on.

FAN

The fan is turned on.

%RH

Humidifying

%RH

Dehumidifying

SUN

Operating at the occupied (day)

temperature.

MOON

Operating at the unoccupied

(night) temperature.

tekmarNet®

Communication is present.

WARNING SYMBOL

Indicates an error is present.

ARROWS

Adjust the displayed setting.

SCENE AWAY

Operating at Away temperature.

TEMPORARY HOLD

Holds temperature for 3, 6, 9 or

12 hours.

WWSD

Warm Weather Shut Down.

COOL

Cooling system is on.

MIN or MAX

Reached the room min or max.

MIN FL or MAX FL

Reached the floor min or max.

Home Screen

Symbols Description

User Interface

Adjust

the Time

Adjust the

Schedule

Display Humidity, Heat

Cool settings, Floor or

Outdoor temperature

Away Key

Switch between

Auto, Heat,

Cool, Off &

Emergency Mode

Return to the

‘Home’ Screen

from any menu

Adjust the

Temperature

Room

Temperature

Turn the Fan on

Home

Button

9 of 48

A Watts Water Technologies Company

Programmable Settings

Press and hold the Home button for 3 seconds to enter the programming menus. The

thermostat returns to the last programming menu previously used.

Programming Menus

Select a Programming Menu

-----------------------------------------

Touch “NEXT” to advance (clockwise in above illustration) to the next menu.

Touch “BACK” to go backwards (counterclockwise in above illustration) through

the menus.

Touch “ENTER” to enter a menu.

Setting Items

--------------------------------------------------------

Touch or arrow to adjust the setting if required.

Touch “NEXT ITEM” to advance to the next item within the menu.

Touch “BACK ITEM” to go backwards to the previous item within the menu.

To return to the parent menu after changing a setting, press and release the

Home button.

To return to the Home screen, press and release the Home button twice or wait

30 seconds to automatically return to the Home screen.

•

Press and

hold for 3

seconds to

access the

programming

menus.

10 of 48

A Watts Water Technologies Company

Set Temp Menu (1 of 4)

Setting Display

SET HEAT ROOM

Set the room heating temperature for the event.

Room

Access Level: Installer, User Range: 40 to 95°F (4.5 to 35.0°C)

Conditions: Always available. Default: 70°F (21.0°C)

SET HEAT ROOM

Set the room heating temperature for the event.

Room

Access Level: Installer, User Range: 40 to 95°F (4.5 to 35.0°C)

Conditions: Schedules are in use or Scenes are

set to All or Guest. Default: 65°F (18.5°C)

SET HEAT ROOM AWAY

Set the room heating temperature for the Away

scene.

Room

Access Level: Installer, User Range: 40 to 95°F (4.5 to 35.0°C)

Conditions: Scenes is set to Away, All or Guest. Default: 62°F (16.5°C)

HEAT MINIMUM ROOM LIMIT

Set the minimum room heating limit.

Access Level: Installer Range: 40 to 95°F (4.5 to 35.0°C)

Conditions: Always available. Default: 40°F (4.5°C)

HEAT MAXIMUM ROOM LIMIT

Set the maximum room heating limit for the

event.

Access Level: Installer Range: 40 to 95°F (4.5 to 35.0°C)

Conditions: Always available. Default: 85°F (29.5°C)

HEAT MAXIMUM ROOM LIMIT

Set the maximum room heating limit for the

event.

Access Level: Installer Range: 40 to 95°F (4.5 to 35.0°C)

Conditions: Schedules are in use or Scenes are

set to All or Guest. Default: 85°F (29.5°C)

SET HEAT FLOOR

Set the floor heating temperature for the event.

Floor

Access Level: Installer, User Range: 40 to 95°F (4.5 to 35.0°C)

Conditions: Room Sensor set to OFF and Sensor

1 or Sensor 2 set to Floor. Default: 72°F (22.0°C)

Autres manuels pour tekmarNet 553

Table des matières

Autres manuels Tekmar Thermostat

Tekmar

Tekmar 519 Manuel utilisateur

Tekmar

Tekmar 508 Manuel utilisateur

Tekmar

Tekmar 527 Manuel utilisateur

Tekmar

Tekmar tekmarNet 4 544 Manuel utilisateur

Tekmar

Tekmar D528 Manuel utilisateur

Tekmar

Tekmar tekmarNet 4 538 Manuel utilisateur

Tekmar

Tekmar tekmarNet2 Thermostat 530 Manuel utilisateur

Tekmar

Tekmar D 512 Manuel utilisateur

Tekmar

Tekmar tekmarNet 557 Manuel utilisateur

Tekmar

Tekmar tekmarNet 2 Thermostat 529 Manuel utilisateur

Tekmar

Tekmar 511 Manuel utilisateur

Tekmar

Tekmar 509 Manuel utilisateur

Tekmar

Tekmar 519 Manuel utilisateur

Tekmar

Tekmar tekmarNet 552 Manuel utilisateur

Tekmar

Tekmar tekmarNet 4 Manuel utilisateur

Tekmar

Tekmar tekmarNet 553 Manuel utilisateur

Tekmar

Tekmar D 054 Manuel utilisateur

Tekmar

Tekmar tekmarNet 4 Manuel utilisateur

Tekmar

Tekmar tekmarNet 552 Manuel utilisateur

Tekmar

Tekmar D538 Manuel utilisateur

Tekmar

Tekmar tNt 540 Manuel utilisateur

Tekmar

Tekmar tekmarNet 552 Manuel utilisateur

Tekmar

Tekmar 545 tekmarNet 4 Manuel utilisateur

Tekmar

Tekmar tekmarNet 4 543 Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur