TechniSat AMC-6 Manuel utilisateur
Broadband
Modem Installation Guide
Release Versions AMC-6 72.0W Ku Band
•StarConnect SAT VPN Software Version 2.02
•Broadband4PC Software Version 4.3.2
Manual last revised 12/2006
Federal Communications Commission Radio Frequency Interference Statement
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. However, if this equipment does cause interference to radio or television
equipment reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
• Use a shielded and properly grounded I/O cable and power cable to ensure compliance of this unit to the specified limits of the rules.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference that may cause undesired operation.
1
2
Contents
Chapter 1: Getting Started - Installing Broadband Modem ............…......……….. 1-1
Package Contents 1-1
System Requirements 1-2
AOL Client Notice 1-3
Static Electricity Warning 1-4
Installing Internal PCI Satellite Modem 1-5
Installing external USB Satellite Modem 1-6
Chapter 2: Installing Driver ……………………………...................…........................ 2-1
Windows XP 2-1
Chapter 3: Installing the Software. 3-1 …………………….……………………………3-1
Chapter 4: Entering Settings ……………………………………………................…... 4-1
Changing Transponder Frequencies 4-1
Editing User Information 4-2
Editing User Settings 4-3
Chapter 5: Dial-up Setup....………………………………....................................……..5-1
Windows XP 5-1
Creating the Dial-up Icon 5-2
Editing Network Connection Settings 5-3
Getting Online 5-4
Warning:Before installing your drivers and
software, please disable your Firewall protection and
leave it off until you actually connect to a website for the
first time. At that time you can re-enable your Firewall
protection. Failure to do this may cause erratic behavior
with your satellite software.
3
1 Getting Started – Installing B2C2 Broadband
Modem
Package Contents
Each package should contain the following items:
Either a TechniSat Internal (PCI) or a TechniSat USB Satellite Modem
InstallationCD
Power Supply (USB modem only)
USB Cable (USB modem only)
User’sGuide
System Requirements
Pentium II 700 MHz or higher, with modem installed.
Microsoft Windows XP – Home Edition/Professional (Service Pack 2 or higher required)
Microsoft Windows 2000 Professional/Server (Service Pack 4 or higher recommended)
256 MB minimum of system memory
30 MB of hard disk space available
1 available USB Port (for external USB satellite modem)
3D graphics recommended
Microsoft Internet Explorer (web browser) version 6.0 installed (Service Pack 2 or higher required)
Microsoft Windows Media Player Version 9.0 or later
Microsoft DirectX 9 or later.
AOL Client Notice: Industry wide, the AOL application, which is loaded onto an AOL’s customers
PC, is very much intrusive in nature, as it does not like to operate with any other Internet Service
Provider other than AOL. The AOL application tends to cause conflicts with other Internet based
services such as cable modem, DSL, and satellite. Therefore, it is highly recommended that the AOL
application be removed from your PC prior to having the B2C2 satellite modem and the TechniSat
software installed on your PC. In the event that you elect not to remove the AOL application from your
PC prior to installing the B2C2 satellite modem and the TechniSat software, NRBB does not assume
any responsibility for any applications that may malfunction after the installation of the B2C2 satellite
modem and the TechniSat software. It is important to note that it is possible to remove the AOL
application and still retrieve your AOL email, be part of the AOL Instant Messenger list, etc. using a
standard Internet browser (i.e. Internet Explorer, Netscape, etc.), if desired, together with the satellite
modem. Once AOL is removed and all of the satellite software installed and running, you can re-
install AOL 9.0.
Static Electricity Warning
To prevent static damage to electronic components, observe the following precautions:
ÌTouch an anti-static or grounded surface such as a large metal object to discharge static from
your body before you remove the electronic components from their packaging and before touching
system components.
ÌHandle system components only at the corners. Never touch any of the metal parts of the
electronic components, such as the golden pins that plug into the slot.
Installing The Internal B2C2 Satellite PCI Modem
To install the internal PCI satellite modem, first insure that the computer is turned off. Following your
PC manufacturer’s instructions, do the following:
1. Turn the PC off and unplug the power supply.
2. Open the side panel or rear cover of your computer to expose the PCI slots.
3. Choose an empty PCI slot you want to place the board in. Unscrew the slot’s metal dust protector
located on the back cover of the case. Lay the protector to one side.
4. Hold the internal PCI satellite modem so that the satellite modem’s IC chips are facing downward,
the metal contacts are toward the PCI slot.
5. Insert the internal PCI satellite modem firmly into the PCI slot as shown in Figure 1-1.
Figure 1-1
6. Tighten the screw on the rear of the internal PCI satellite modem so that it is firmly secured to the
computer chassis (if available).
7. Replace the access cover of your computer case.
4
Installing External USB Satellite Modem
To install the external USB satellite modem, do the following steps. There’s no need to turn off the
computer at this time.
1. Connect the power cord, one end to the power outlet, the other to the DC IN connector on the back
of the external USB satellite modem.
2. Connect the external USB satellite modem cable, one end to the USB port on the PC. DO NOT
connect the other end to the USB port on the back of the external USB satellite modem yet.
3. Connect the coaxial cable from the satellite dish to the female plug on the TechniSat modem you
just installed.
2 Installing Drivers
(*The PCI and USB drivers are located on the CD supplied with your B2C2 satellite modem. It is
necessary to install the modem and drivers prior to installing the satellite software) Our drivers
support Windows XP and Windows 2000 Professional. The procedure for the driver installation for the
Internal PCI satellite modem and the External USB satellite modem are the same. If installing the
External USB satellite modem drivers, plug in the USB cable into the back of the B2C2 satellite
modem at this time.
Windows XP
To install the B2C2 satellite modem driver on Windows XP, you must be logged on as an
Administrator or have Administrator Privileges.
1. When you start your computer for the first time after installing the B2C2 internal PCI satellite
modem, or after plugging in the external B2C2 USB satellite modem, the Plug-N-Play feature
should recognize the new modem installed (Figure 2-1).
Figure 2-1
5
2. The New Hardware Wizard window will appear (Figure 2-2). Click the bottom radio button to
select “No, not this time” (If this window does not appear on your system, skip to Step 3). Then
click Next to continue.
Figure 2-2
3. Select the radio button to install the software automatically, then click Next to continue
(Figure 2-3).
Figure 2-3
6
4. The computer will now search through the CD for the appropriate drivers (Figure 2-4).
Figure 2-4
5. Select Continue Anyway when reported that the TechniSat modem has not passed Windows
Logo testing as shown below in Figure 2-5.
Figure 2-5
6. Windows XP continues installing for the correct drivers (Figure 2-6).
7
Figure 2-6
7. After Windows XP finds and installs the appropriate drivers, click Finish (Figure 2-7).
Figure 2-7
8. Windows XP will then display that the new hardware was found, is installed and is ready to use
(Figure 2-8).
8
Figure 2-8
9. Remove the CD from the CD Rom drive and restart your computer.
You have successfully installed the drivers and are ready to install the TechniSat modem software.
Proceed to Chapter 3: Installing The Software.
3 Installing the Software
The application used to configure and maintain the TechniSat modem is located on the installation
CD provided with the B2C2 PCI or USB modem. To install it, you’ll need to insert the CD into the CD
Rom drive.
1. Windows XP will automatically start the CD and ask you to select the Setup language. Then
click OK (Figure 3-1).
Figure 3-1
9
2. The Install Shield Wizard will start to load automatically (Figure 3-2).
Figure 3-2
3. The software License Agreement will be displayed next as shown in Figure 3-3 below. Click
Yes to continue with the software installation. If you select No, the software will not be
installed.
Figure 3-3
10
Ce manuel convient aux modèles suivants
1
Table des matières
Manuels Modem populaires d'autres marques
Davicom
Davicom DM562AP Manuel utilisateur
EpiValley
EpiValley TATA indicom SXC-1080 Manuel utilisateur
Zte
Zte WiMAX Manuel utilisateur
Intelimax
Intelimax MA-2060 Manuel utilisateur
SMC Networks
SMC Networks D3CM1604V Manuel d'utilisation et d'entretien
Telstra
Telstra Wi-Fi 4G Advanced Pro X Manuel utilisateur
US Robotics
US Robotics 3453C Manuel utilisateur
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuel utilisateur
Zte
Zte MF823 Manuel utilisateur
Four-Faith
Four-Faith F1403 Manuel utilisateur
Sierra Wireless
Sierra Wireless AIRLINK MP595W Manuel utilisateur
Gemtek
Gemtek WiMAX WIXFBR-103 Manuel utilisateur