Technica Engineering 100base-t1_SPY Manuel utilisateur

User Manual

Version 1.2

September 2017

BroadR-Reach –Standard Ethernet

100BaseT1_SPY

Page 1of 43

The user can download the latest firmware and documentation for the 100BASET1_SPY here:

http://www.technica-engineering.de/SPY

Note: This User Manual version is related to 100BASET1_SPY Firmware version 1.12.

Page 2of 43

Index

1 Feature List ..................................................................................................................................... 3

2 Warranty and Safety Information................................................................................................... 4

3 Pinning ............................................................................................................................................ 5

3.1 Power connector (top left)...................................................................................................... 6

3.2 BroadR-Reach connectors ....................................................................................................... 7

3.3 RJ45 Ethernet connectors ....................................................................................................... 8

3.4 SMA Connector........................................................................................................................ 8

4 Status LEDs and Pushbutton........................................................................................................... 9

5 Configuration Website.................................................................................................................. 10

5.1 Website Home....................................................................................................................... 11

5.2 System Information Tab ........................................................................................................ 11

5.3 Control Panel Tab .................................................................................................................. 12

5.4 Switch Status Tab .................................................................................................................. 13

5.4.1 Global Configuration: .................................................................................................... 13

5.4.2 Spy Multiplexer.............................................................................................................. 14

5.4.3 Gigabit Ethernet Ports................................................................................................... 15

5.4.4 BroadR-Reach Port ........................................................................................................ 16

5.4.5 CAN Port ........................................................................................................................ 18

5.4.6 LIN Port.......................................................................................................................... 22

5.4.7 FlexRay Port................................................................................................................... 25

6 Structure of an Ethernet 100BASET1_SPY RAW frame ................................................................ 26

6.1 Structure of the BroadR-Reach payload................................................................................ 28

6.2 Structure of the CAN payload................................................................................................ 29

6.3 Structure of the LIN payload ................................................................................................. 30

6.4 Structure of the FlexRay payload .......................................................................................... 32

6.5 100BASET1_SPY LUA Installation Guide................................................................................ 33

7 UseCases....................................................................................................................................... 35

7.1 100BaseT1_SPY UseCase....................................................................................................... 35

8 Hardware Variants........................................................................................................................ 36

8.1 BroadR-Reach Analog Filter................................................................................................... 36

8.2 Debug connector................................................................................................................... 36

8.3 Startup Time.......................................................................................................................... 37

9 Application Firmware Update....................................................................................................... 38

10 Frequently Asked Questions –FAQ .............................................................................................. 41

11 Contact.......................................................................................................................................... 42

Page 3of 43

1Feature List

The Technica Engineering 100BaseT1_SPY samples data Frames directly on the bus without influence

of the original network. The data Frames are enhanced with additional information as an exact

timestamp and the bus port the data was originally sent on. All data can be recorded on a PC or

datalogger for detailed offline analysis.

Timestamps are in 0.04 μs resolution and synchronous to all connected lines.

Optionally other UseCases (Frame Generator, Fault Injection, Data Manipulation, Trigger Generator,

… ) can be upgraded.

Features:

12x BroadR-Reach Ports Fullduplex 100 Mbit/s

1x FlexRay Channel A (option for transmission of StartUp & Sync Frames)

5x CAN / CAN-FD Ports

1x LIN, 1x SMA Trigger

4x Gigabit Ethernet Ports for Logging data output

1x Fast Ethernet Port for status output, configuration and webserver access

1x SD Card for configuration and storage of trigger events

Stainless steel case

Power requirement: 12 Volt DC Nominal (7-16 Volt)

Power consumption: 10 Watt

Size: 147 x 124 x 26mm

Weight: 0,9 kg

International Protection: IP 2 0

Operating Temperature: -40 to +80 °Celsius

Page 4of 43

2Warranty and Safety Information

Before operating the device, read this manual thoroughly and retain it for your

reference.

The latest firmware and documentation can be downloaded for the

100BASET1_SPY through the following link:

http://www.technica-engineering.de/SPY

Use the device only as described in this manual.

Use only in dry conditions.

Do not apply power to a damaged device.

Do not open the device. Otherwise warranty will be lost.

This device is designed for engineering purpose only.

Special care has to be taken for operation.

Do not use this device in a series production car.

As this device is likely to be used under rough conditions, warranty is limited to 1

year.

Manufacturer liability for damage caused by using the device is excluded.

Page 5of 43

3Pinning

The pinning of the ECU connectors is listed on the label on top of the device.

The Tyco Electronics (TE) Nano Micro Quad Lock System (NanoMQS) is used.

Name

Part Number

20POS

NANOMQS

REC HSG

CODE A

2141404-1

NANOMQS

RECEPTACLE TERMINAL

2-1703930-1

http://www.te.com/usa-en/product-2141404-1.html

http://www.te.com/usa-en/product-2-1703930-1.html

http://www.te.com/usa-en/product-4-1579014-0.html

http://de.farnell.com/te-connectivity/2-1703930-1/contact-socket-crimp/dp/2528666

Official Crimp Tool:

TE CONNECTIVITY CS11K NANO-MQS, 0.13-0.35 SQ.M

TE Internal Number: 4-1579014-0

Distributor:

Börsig GmbH

Siegmund-Loewe-Str. 5

74172 Neckarsulm

www.boersig.com

Page 6of 43

3.1 Power connector (top left)

Power supply for the device is supplied by Pin 18 (12Volt) and Pin 20 (Ground).

Requirements for the 100BASET1_SPY itself: 12 Volt DC up to 1 Ampere (typical 600mA)

Warning:If a voltage higher than 16 Volt is applied, the device will be damaged!

A wakeup-line may be connected on pin 5. The wakeup-line should have the same voltage level as

the power supply (12 Volt). A high level on one of these pins wakes up the ECU from sleep mode and

keeps it active.

Alternatively, the “Prevent sleep” checkbox in the control panel of the website can be enabled.

The CAN interfaces can be used to communicate with the Microcontroller by CAN and CAN-FD bus.

The LIN interface can be used to communicate with the Microcontroller by LIN bus.

The FlexRay interface can be used to communicate with the Microcontroller by FlexRay bus. In the

default software there is no data transmission specified.

Page 7of 43

Function

GND Reference for Trigger

Host Trigger Line

LIN Bus

FlexRay Channel A BP

Wake Line

FlexRay Channel A BM

CAN D / 5 Minus (Low)

CAN E / 1 Plus (High)

CAN D / 5 Plus (High)

CAN E / 1 Minus (Low)

n.c.

CAN C / 2 Plus (High)

CAN B / 4 Minus (Low)

CAN C / 2 Minus (Low)

CAN B / 4 Plus (High)

n.c.

CAN A / 3 Minus (Low)

Battery +12 Volt Input

CAN A / 3 Plus (High)

Battery Ground Input

3.2 BroadR-Reach connectors

The pins marked with (P) or (M) are used for the BroadR-Reach ports.

The user has to connect the (P) pin to the (P) pin of the periphery device.

The user has to connect the (M) pin to the (M) pin of the periphery device.

Note: If these two pins are swapped, the link LED may be lit on the BroadR-Reach slave side, but no

data transmission will be possible.

Middle Connector

Function

GND Reference for Trigger

FPGA Trigger Line OUT1

n.c.

BroadR-Reach Port 3A / 5, P (Positive)

BroadR-Reach Port 3B / 6, P (Positive)

BroadR-Reach Port 3A / 5, M (Negative)

BroadR-Reach Port 3B / 6, M (Negative)

n.c.

BroadR-Reach Port 2A / 4, P (Positive)

BroadR-Reach Port 2B / 3, P (Positive)

BroadR-Reach Port 2A / 4, M (Negative)

BroadR-Reach Port 2B / 3, M (Negative)

n.c.

BroadR-Reach Port 1A / 1, P (Positive)

BroadR-Reach Port 1B / 2, P (Positive)

BroadR-Reach Port 1A / 1, M (Negative)

BroadR-Reach Port 1B / 2, M (Negative)

Outer Connector

Function

GND Reference for Trigger

FPGA Trigger Line IN1

n.c.

BroadR-Reach Port 6A / 9, P (Positive)

BroadR-Reach Port 6B / 12, P (Positive)

BroadR-Reach Port 6A / 9, M (Negative)

BroadR-Reach Port 6B / 12, M (Negative)

n.c.

BroadR-Reach Port 5A / 8, P (Positive)

BroadR-Reach Port 5B / 11, P (Positive)

BroadR-Reach Port 5A / 8, M (Negative)

BroadR-Reach Port 5B / 11, M (Negative)

n.c.

BroadR-Reach Port 4A / 7, P (Positive)

BroadR-Reach Port 4B / 10, P (Positive)

BroadR-Reach Port 4A / 7, M (Negative)

BroadR-Reach Port 4B / 10, M (Negative)

Page 8of 43

3.3 RJ45 Ethernet connectors

There are four RJ45 Standard Ethernet connectors of the front side for Gigabit Ethernet.

There is one RJ45 Standard Ethernet connector of the front side for Fast Ethernet (100 Bit/s)

3.4 SMA Connector

There is one shielded SMA Connector for one Trigger Input/Output Line.

Page 9of 43

4Status LEDs and Pushbutton

The 100BASET1_SPY has several status LEDs at the front side of the case.

The “Host” LED1 can toggle at three different speeds:

Slow toggle (approx. 0.5 sec) during normal operation to show that the microcontroller is running in

normal mode.

Fast toggle (approx. 0.1 sec) when the microcontroller is in bootloader mode. The bootloader mode

is used for firmware update only (see below in this manual). The user cannot access the website

when the device is in bootloader mode.

When the device is in Bootloader-Update Mode the LED toggles with moderate frequency (approx.

0.25 sec).

The “Host” LED2 should be normally off. If it toggled at high speed (approx. 0.1 sec) an error has

been detected by the Host.

The “FPGA” LED2 can toggle at two different speeds:

Slow toggle (approx. 0.5 sec) during normal operation to show that the FPGA is running in normal

mode.

Fast toggle (approx. 0.1 sec) : TBD

The “FPGA” LED1 should be normally off. If it toggled at high speed (approx. 0.1 sec) an error has

been detected by the FPGA.

The 12 port status LEDs 1A to B6 monitor the link status of the corresponding port. The LEDs are lit

when there is BroadR-Reach link detected.

Note: There is an issue when P/N of the bus are swapped. The LED may be on in this case on BroadR-

Reach slave side, but there will be no data transmission possible.

The built-in LEDs in RJ45 connector shows the status of the gigabit ports. The left (orange LED) is lit

by a link-up. The right (yellow) will blink on data traffic.

The Rotary DIP Switch has four modes:

1: TBD

2: TBD

3: TBD

4: TBD

Table des matières

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

Cypress

Cypress CY4607 HX2VL Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur