TEC ST-71 SERIES Manuel utilisateur

PRINTED IN JAPAN

TEC POS Terminal

ST-71 SERIES

Document No. EO18-12010

Original Dec., 2005

(Revised )

NOTE:

Model names that end with "-R" are RoHS compliant models. If "-R" is not

attached, that model is non RoHS compliant.

Never install non RoHS compliant optional equipment or parts on a RoHS

compliant machine which is supposed to be used in the countries that enforce

the RoHS directive, as doing this is legally prohibited.

Maintenance Manual

WARNING!

Follow all manual instructions. Failure to do so could create safety hazards such as fire or

electrocution.

NOTES: 1. Manual instructions must be followed when installing option kits or adding cables to

avoid system failures and to insure proper performance and operation.

2. Failure to follow manual instructions or any unauthorized modification, substitution

or change to this product will void the limited product warranty.

EO18-12010

(Revision Date: Jan. 30, 2006)

TABLE OF CONTENTS

Page

1. UNPACKING ..............................................................................................................1- 1

1.1 Procedure........................................................................................................................1- 1

1.2 Checks.............................................................................................................................1- 1

1.3 Tapes...............................................................................................................................1- 2

1.4 Notes for Installation........................................................................................................1- 2

2. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT................................2- 1

2.1 Installing the Hard Disk Drive (HDD)...............................................................................2- 2

2.2 Installing the LVDS PC Board and Back Indicator Unit ...................................................2- 5

(KIT-71-DSP1, TFTST-71-2A/5A Series)

2.3 Installing the Line Display, Pole Unit, and VFD Stand....................................................2-10

(LIUST-71-BAAK, KIT-71-POLE, and KIT-71-BASE Series)

2.4 Installing the PCMCIA/CF PC Board (MIFST-71-2 Series) ............................................2-19

2.5 Installing the COM5 or COM6 Connector (KIT-71-COM Series)....................................2-23

2.6 Installing the MCR Unit (MCRST-71-3, KIT-71-RELY Series)........................................2-25

2.7 Installing the iButton Unit (KIT-71-BTN1, KIT-71-RELY Series).....................................2-31

2.8 Installing the Additional Memory.....................................................................................2-33

3. CONNECTORS/SHORT PIN AND DIP SWITCH SETTING.......................................3- 1

3.1 Connectors......................................................................................................................3- 1

3.2 Short Pin and DIP Switch Setting....................................................................................3- 3

4. BIOS SETUP ..............................................................................................................4- 1

4.1 General............................................................................................................................4- 1

4.2 Basic Operation and Keys Used......................................................................................4- 1

4.3 BIOS Setup Screen Configuration and Default Setting ...................................................4- 5

4.4 Notes and Restrictions ...................................................................................................4-21

5. DIAGNOSTIC TEST OPERATION.............................................................................5- 1

5.1 Outline.............................................................................................................................5- 1

5.2 Serviceman Diagnostic Test Program Setup Procedure.................................................5- 2

5.3 ST-71 Diagnostic Menu..................................................................................................5-14

5.4 BIOS Diagnostic Test Program ......................................................................................5-15

5.5 Serviceman Diagnostic Test Program............................................................................5-24

6. PERIODIC MAINTENANCE .......................................................................................6- 1

6.1 Procedure of Periodic Maintenance ................................................................................6- 1

7. TROUBLESHOOTING................................................................................................7- 1

EO18-12010

CAUTION!

1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA

TEC.

2. The contents of this manual may be changed without notification.

3. Please refer to your local Authorised Service representative with regard to any queries you

may have in this manual.

by TOSHIBA TEC CORPORATION

ll Rights Reserved

570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN

NOTE: Pictures in this manual show that body colour may differ from that of the original.

Page

8. MAIN UNIT REPLACEMENT .....................................................................................8- 1

8.1 Operator’s Display Section..............................................................................................8- 1

8.2 Bottom Cover Section......................................................................................................8- 7

9. APPENDIX..................................................................................................................9- 1

9.1 Serial Interface COM1 to COM6......................................................................................9- 1

9.2 VGA Connector ...............................................................................................................9- 2

9.3 DRW1, DRW2 (Cash Drawer 24V Type).........................................................................9- 2

9.4 LAN..................................................................................................................................9- 2

9.5 USB.................................................................................................................................9- 3

9.6 PS/2 (Keyboard, Mouse) .................................................................................................9- 3

9.7 24V OUT Connector........................................................................................................9- 3

9.8 LINEOUT.........................................................................................................................9- 3

9.9 MIC..................................................................................................................................9- 3

9.10 LVDS1 Connector............................................................................................................9- 4

9.11 Parallel (LPT) Connector.................................................................................................9- 4

9.12 Powered USB (24V) Connector.......................................................................................9- 5

9.13 Powered USB (12V) Connector.......................................................................................9- 5

1. UNPACKING EO18-12010

1.1 Procedure

1- 1

1. UNPACKING

1.1 Procedure

1) Open the carton.

2) Take the accessories out of the carton.

3) Take out the POS terminal, then remove the pads.

4) Place the POS terminal on a level surface.

1.2 Checks

1) Check for the damage or scratches on the machine.

2) Confirm that none of the accessories are missing.

Detailed information of each accessory is as shown below.

Accessory Quantity Usage

Bind Screw M-3x3 8 Used to secure the Hard Disk Drive (HDD) to the HDD

Holder.

Ferrite Core 1 Attached to the cable when using the option HS-530 Handy

Scanner.

Owner’s Manual 1

Ferrite Core (1 pc.)

Bind Screw M-3x3

(8 pcs.)

Pad

Carton

ST-71 POS Terminal

Carton

1. UNPACKING EO18-12010

1.3 Tapes

1- 2

1.3 Tapes

Remove all the tapes from the POS terminal.

1.4 Notes for Installation

WARNING!

1. Care must be taken not to get your fingers caught between the LCD Frame and the POS terminal

when bending the display backward.

2. DO NOT raise the LCD Frame while the Front Cover is not in position. When the LCD Frame is

raised at right angle (90°) or more, the LCD may fall under its own weight, and your fingers may be

caught.

CAUTION!

1. When removing the protective film from the display surface, please be sure to do it slowly. If it is

done quickly, static electricity may generate, and the TFT may be damaged.

2. When installing the POS terminal, take the following precautions. Failure to do this may cause fire,

electric shock, or injury.

(1) Avoid locations where it is subject to the following:

• Direct sunlight

• High temperature, high humidity

• Rapid change in temperature

• Excessive vibration

• Dust

(2) Keep away from any devices that emit magnetism or electromagnetic wave.

(3) Keep away from flame or moisture.

(4) Be sure to place the POS terminal on a level and stable surface.

1. Place the POS terminal on a level surface.

2. Provide a minimum space to the left, right, front and rear of the POS terminal for proper cooling.

(The unit has air vents and a fan on the front and left. Spaces should be provided to prevent the air vents

from being blocked and the air flow from being obstructed.)

NOTE: A fan is provided on these sides. Do not prevent the ventilation of the fan.

80 mm

(

See NOTE.

)

80 mm 80 mm

80 mm

See NOTE.

2. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-12010

2.1 Installing the Hard Disk Drive (HDD)

2- 1

2. INSTALLATION PROCEDURE FOR OPTIONAL

EQUIPMENT

WARNING!

1. Disconnect the power cord before installing the optional parts.

2. Be careful not to short-circuit the lithium battery on the ENGINE PC board.

NOTES:

1. When assembling, be careful not to let the Front Cover catch any cables. Lead the cables through the U-

shaped holes on the Front Cover so that the Front Cover is closed correctly.

2. When the cable is connected to the USB port, lead the cable obliquely downward then secure with the fasten

band as shown below. If lead directly below, the cable may come off.

This section describes procedures to install optional equipments into the POS terminal.

Front Cover

Fasten Band

USB Cable

2. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-12010

2.1 Installing the Hard Disk Drive (HDD)

2- 2

2.1 Installing the Hard Disk Drive (HDD)

CAUTION!

1. For the specification of an HDD to be installed, please refer to the POS Optional Device (Document

No. EO21-12001), POS OPTIONAL DEVICE BASIC SPECIFICATION.

2. Please use TOSHIBA TEC approved HDDs. Failure to do this may cause an error.

Installation procedure for the first HDD is shown below.

• Required Parts

The following part is required to install an HDD.

HDD Unit (locally procured) HDD Fixing Screw M-3x3 (8 pcs.)

(NOTE)

NOTE: This is an accessory part of the POS terminal.

• Installation Procedure

1) Remove the two Rubber Caps from the Rear Cover.

2) Remove the two screws then remove the Rear Cover.

Rubber Cap

and

DSM-4x10 Screw

Rear Cover

2. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-12010

2.1 Installing the Hard Disk Drive (HDD)

2- 3

3) Let the HDD Cable off the HDD Holder.

4) Remove the two screws, then remove the HDD Holder in the direction as indicated by the arrow.

(Carefully remove the HDD Holder on which the two hooks are provided.)

5) Insert an HDD into the HDD Holder, then secure with the four HDD fixing screws. (The four out of eight

pieces of option HDD fixing screws are used for an HDD.)

6) Connect the HDD Connector to the HDD.

Screw

M-3x3

HDD Cable HDD Holder

Hook

HDD

HDD Holder

Screw M-3x3

2. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-12010

2.1 Installing the Hard Disk Drive (HDD)

2- 4

7) Fit the HDD Holder Hooks into the positioning holes which are provided on the frame, then secure with the

two screws.

8) Reassemble in the reverse order of removal.

9) After the installation is completed, perform an HDD test in the BIOS diagnostic test program. Then, make

sure that the HDD performs properly. (Refer to Section 5.4 BIOS Diagnostic Test Program.)

< Installation of the second HDD >

When installing the second HDD, connect the HDD Interface Cable as shown below.

Screw

M-3x3

Hook

HDD Interface Cable

Primary IDE

(RISER PC Board)

2nd HDD (Slave)

1st HDD (Master)

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TEC Terminal tactile

TEC

TEC ST-6500 Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

NCR

NCR RealPOS 7460-2 Manuel

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur