TE Connectivity PRO-CRIMPER III Manuel utilisateur

Chipsmall Limited consists of a professional team with an average of over 10 year of expertise in the distribution

of electronic components. Based in Hongkong, we have already established firm and mutual-benefit business

relationships with customers from,Europe,America and south Asia,supplying obsolete and hard-to-find components

to meet their specific needs.

With the principle of “Quality Parts,Customers Priority,Honest Operation,and Considerate Service”,our business

mainly focus on the distribution of electronic components. Line cards we deal with include

Microchip,ALPS,ROHM,Xilinx,Pulse,ON,Everlight and Freescale. Main products comprise

IC,Modules,Potentiometer,IC Socket,Relay,Connector.Our parts cover such applications as commercial,industrial,

and automotives areas.

We are looking forward to setting up business relationship with you and hope to provide you with the best service

and solution. Let us make a better world for our industry!

Tel: +86-755-8981 8866 Fax: +86-755-8427 6832

Email & Skype: [email protected]om Web: www.chipsmall.com

Address: A1208, Overseas Decoration Building, #122 Zhenhua RD., Futian, Shenzhen, China

  

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.

1of 6

Instruction Sheet

TOOLING ASSISTANCE CENTER

1-800-722-1111



PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com

LOC B

408-9819

PRO-CRIMPER* III Hand Crimping

Tool Assembly 58495-1 with

Die Assembly 58495-2 05 MAY 11 Rev D

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use

and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

Figure 1

1. INTRODUCTION

PRO-CRIMPER III Hand Crimping Tool Assembly

58495-1 consists of Die Assembly 58495-2 and PRO-

CRIMPER III Hand Crimping Tool Frame 354940-1.

The die assembly consists of crimping dies and a

locator assembly.

Read these instructions thoroughly before crimping

any contacts.

Dimensions on this sheet are in millimeters [with

inch equivalents provided in brackets]. Figures and

illustrations are for identification only and are not

drawn to scale.

Reasons for reissue are provided in Section 11,

REVISION SUMMARY.

Stationary Jaw

Back of Tool

(Wire Side)

Pivot Pin

PRO-CRIMPER III Hand

Crimping Tool Frame

354940-1 (408-9930)

Stationary

Handle

Locator Assembly

(Supplied with

Die Assembly)

Front of Tool

(Locator Side)

Die Assembly

Moving

Jaw

Ratchet

Adjustment

Wheel

The PRO-CRIMPER III Hand Crimping Tool is a “Commercial" grade tool and is

designed primarily for field installation, repair, maintenance work, or prototyping in

industrial, commercial, or institutional applications. Product crimped with this tool will

meet the crimp height requirement for hand tools in the appropriate 114 series

specification, but may not comply with other feature parameters of the specification.

TE offers a variety of tools to satisfy your performance requirements. For additional

information, contact the Technical Assistance Center at 1-800-722-1111.

Moving Handle

TE DIE

ASSEMBLY

LOCATOR

ASSEMBL†

CONTACT

FAMILY‡

WIRE

SIZE

(AWG)

INSUL

DIA

STRIP LENGTH

(mm [In.])

58495-2 58515-1

Multimate

Type III(+) and

Type VI

Contacts

28 - 24 .89 to 1.40

[.035 to .055]

3.17

[.125]

24 - 20 1.02 to 2.03

[.040 to .080]

18 - 16 2.03 to 2.54

[.080 to .100]

† Supplied with die assembly. Also available separately. ‡ Contact the Technical Assistance Center or Product Information (below) for specific

product information.

NOTE

408-9819

2of 6

Rev D

Figure 2

2. DESCRIPTION (Figure 1 and FIgure 2)

The tool features a tool frame with a stationary jaw

and handle, a moving jaw, a moving handle, and an

adjustable ratchet that ensures full contact crimping.

The tool frame holds a die assembly with three

crimping sections.

The die assembly features a wire anvil, an insulation

anvil, a wire crimper, and an insulation crimper.

Attached to the outside of the frame is a locator

assembly, which contains a locator, a spring retainer,

and a contact support.

Die retaining pins and die retaining screws are used to

position and secure the dies in the tool frame. A nut is

used on the upper die retaining screw to hold the

locator assembly in place.

3. INSTALLATION AND REMOVAL OF DIE SET AND

LOCATOR ASSEMBLY (Figure 2)

1. Open the tool handles and remove the two die

retaining screws from the tool jaws.

2. Place the wire anvil and insulation anvil so that

their chamfered sides and their marked surfaces

face outward, when mounted in the moving jaw of

the tool frame.

3. Insert the two die retaining pins.

4. Insert the short die retaining screw through the

jaw and through both anvil dies, and tighten the

screw just enough to hold the dies in place. Do not

tighten the screw completely at this time.

5. Place the wire crimper and insulation crimper so

that their chamfered sides and their marked

surfaces face outward, when mounted in the

stationary jaw of the tool frame.

6. Insert the two die retaining pins.

7. Insert the long die retaining screw through the

jaw and through both crimper dies, and tighten the

screw just enough to hold the dies in place. Do not

tighten the screw completely at this time.

8. Carefully close the tool handles, making sure that

the anvils and crimpers align properly. Continue

closing the tool handles until the ratchet in the tool

frame has engaged sufficiently to hold the anvils

and crimpers in place, then tighten both die

retaining screws.

9. Place the locator assembly over the end of the

long screw, and position the locator assembly

against the side of the tool jaw.

10. Place the nut onto the end of the long screw and

tighten the nut enough to hold the locator assembly

in place, while still allowing the locator to slide up

and down.

11. To disassemble, close the tool handles until the

ratchet releases, remove the nut, the locator

assembly, the two die retaining screws, and the four

die retaining pins, and slide the anvils and crimpers

out of the tool jaws.

Nut

Chamfer

Offset

Wire Anvil Insulation 

Anvil

Insulation

Crimper

Locator

Assembly PRO-CRIMPER III

Hand Tool Frame

Die Retaining

Pins

Die

Retaining

Screws

Wire 

Crimper

Chamfer

Adjustment

Screw for

Contact 

Support

Wire Inserted

to Stop

Back of Tool

(Wire Side)

Contact

Support

Strip

Length

Locator

Contact

(Typ)

Wire Locator in

Wire Stop

Slot

408-9819

3of 6

Rev D

4. CONTACT SUPPORT ADJUSTMENT (Figure 3)

The contact support is preset prior to shipment, but

minor adjustment may be necessary.

1. Make a sample crimp and determine if the

contact is straight, bending upward, or bending

downward.

2. If adjustment is required, loosen the screw that

holds the contact support onto the locator assembly.

The ratchet has detents that create audible clicks

as the tool handles are closed.

3. Place a contact with wire into the proper nest and

close the tool handles until the ratchet reaches the

sixt# click, or until the contact support touches the

contact.

4. Slightly loosen the nut that holds the locator

assembly onto the tool frame.

5. Move the contact support as required to eliminate

the bending of the contact.

6. Tighten the nut and close the handles until the

ratchet releases.

7. Remove and inspect the contact.

8. Make another sample crimp. If the contact is

straight, tighten the contact support screw. If the

contact is still being bent during crimping, repeat the

adjustment procedure.

5. CRIMPING PROCEDURE

This tool is provided with a crimp adjustment feature.

Initially, the crimp height should be verified as

specified in Figure 4. Refer to Section 6, Crimp Height

Inspection, and Section 7, RATCHET (Crimp Height)

Adjustment, to verify crimp height before using the tool

to crimp desired contacts and wire sizes.

Refer to the table in Figure 1 and select wire of the

specified size and insulation diameter. Strip the

wire to the length indicated in Figure 1, taking care

not to nick or cut wire strands. Select an applicable

contact and identify the appropriate crimp section

according to the wire size markings on the tool.

Refer to Figure 3 and proceed as follows:

1. Hold the tool so that the back (wire side) is facing

you. Squeeze tool handles together and allow them

to open fully.

2. Holding the contact by the mating end, insert the

contact - insulation barrel first - through the front of

the tool and into the appropriate crimp section.

Figure 3

NOTE

408-9819

4of 6

Rev D

3. Position the contact so that the mating end of the

contact is on the locator side of the tool, and so that

the open "U" of the wire and insulation barrels must

face the top of the tool. Place the contact up into the

nest so that the movable locator drops into the slot

in the contact. Refer to Figure 3. Butt the front end

of the wire barrel against the movable locator.

Make sure that both sides of the insulation barrel

are started evenly into the crimping section. Do not

attempt to crimp an improperly positioned contact.

4. Hold the contact in position and squeeze the tool

handles together until ratchet engages sufficiently to

hold the contact in position. Do NOT deform

insulation barrel or wire barrel.

5. Insert stripped wire into contact insulation and

wire barrels until it is butted against the wire stop, as

shown in Figure 3.

6. Holding the wire in place, squeeze tool handles

together until ratchet releases. Allow tool handles to

open and remove crimped contact.

The crimped contact may stick in the crimping area,

but the contact can be easily removed by pushing

downward on the top of the locator (see Figure 3)

7. Check the contact's crimp height as described in

Section 6, Crimp Height Inspection. If necessary,

adjust the crimp height as described in Section 7,

RATCHET ADJUSTMENT.

6. CRIMP HEIGHT INSPECTION

Crimp height inspection is performed through the use

of a micrometer with a modified anvil, commonly

referred to as a crimp-height comparator. Tyco

Electronics does not manufacture or market crimp-

height comparators. Detailed information on obtaining

and using crimp-height comparators can be found in

instruction sheet 408-7424.

Proceed as follows:

1. Refer to Figure 4 and select a wire (maximum

size) for each crimp section listed.

2. Refer to Section 5, CRIMPING PROCEDURE,

and crimp the contact(s) accordingly

3. Using a crimp height comparator, measure the

wire barrel crimp height as shown in Figure 4. If the

crimp height conforms to that shown in the table,

the tool is considered dimensionally correct. If not,

the tool must be adjusted. Refer to Section 7,

RATCHET ADJUSTMENT.

7. RATCHET (Crimp Height) ADJUSTMENT (Figure 5)

1. Remove the lockscrew from the ratchet

adjustment wheel.

Figure 4

2. With a screwdriver, adjust the ratchet wheel from

the locator side of the tool.

3. Observe the ratchet adjustment wheel. If a tighter

crimp is required, rotate the adjustment wheel

COUNTERCLOCKWISE to a higher-numbered

setting. If a looser crimp is required, rotate the

adjustment wheel CLOCKWISE to a lower-

numbered setting.

4. Replace the lockscrew.

Figure 5

CAUTION

NOTE

WIRE SIZE

AWG (MAX)

CRIMP SECTION

(WIRE SIZE

MARKING)

CRIMP HEIGHT

DIM. (A) AND

TOLERANCE

16 18 - 16 1.295±.051

[.0510 ±.0020]

20 24 - 20 1.003 ± .051

[.0395 ± 0020]

24 28 - 24 .787 ± .051

[.0310 ± .0020]

Position

Point On

Center of

Wire

Barrel

Opposite

the Seam

Modified Anvil

Screwdriver

Ratchet

Adjustment

Wheel

Lockscrew

(Typ)

408-9819

5of 6

Rev D

5. Make a sample crimp and measure the crimp

height. If the dimension is acceptable, replace and

secure the lockscrew. If the dimension is

unacceptable, continue to adjust the ratchet, and

again measure a sample crimp.

8. MAINTENANCE

Ensure that the tool and dies are clean by wiping them

with a clean, soft cloth. Remove any debris with a

clean, soft brush. Do not use objects that could

damage the tool. When not in use, keep handles

closed to prevent objects from becoming lodged in the

crimping dies, and store in a clean, dry area.

9. VISUAL INSPECTION

The crimping dies should be inspected on a regular

basis to ensure that they have not become worn or

damaged. Inspect the crimp sections for flattened,

chipped, worn, or broken areas. If damage or

abnormal wear is evident, the tool must be replaced.

See Section 10, REPLACEMENT.

10. REPLACEMENT

Customer-replaceable parts are shown in Figure 1.

Available separately, PRO-CRIMPER III Hand

Crimping Tool Repair Kit 679221-1 includes a

replacement nut and a variety of pins, rings, screws,

and springs.

If the dies are damaged or worn excessively, they

must be replaced.

Order the repair kit and replaceable parts through your

TE representative, or call 1-800-526-5142, or send a

facsimile of your purchase order to 1-717-986-7605, or

write to:

CUSTOMER SERVICE (038-035)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

11. REVISION SUMMARY

Since the previous release of this sheet, the new

company logo has been applied.

408-9819

6of 6

Rev D

PRO-CRIMPER III Hand Tool Frame 354940-1

(Instruction Sheet 408-9930)

SDE-SA Hand Tool 9-1478240-0

(Instruction Sheet 408-8851)

SDE Bench Terminator 1490076-2

(Customer Manual 409-10052)

626 Adapter 679304-1

(Instruction Sheet 408-4070)

Electro-Hydraulic (BT 3500 Battery-Hydraulic)

Hand Tool Kits 2031400-[ ]

(Customer Manual 409-10095)

“C”-Head Assembly 2031450-1

(Instruction Sheet 408-10311)

Closed Head Assembly 2031460-1

(Instruction Sheet 408-10312)

Tooling Compatible with Die Assembly 58495-[ ]

Autres manuels pour PRO-CRIMPER III

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TE Connectivity Outils de sertissage

TE Connectivity

TE Connectivity FDH 3000 864 Manuel utilisateur

TE Connectivity

TE Connectivity 2380840-1 Manuel utilisateur

TE Connectivity

TE Connectivity 90084 Manuel utilisateur

TE Connectivity

TE Connectivity 2063573-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2063433-1 Manuel utilisateur

TE Connectivity

TE Connectivity 528008-4 Manuel utilisateur

TE Connectivity

TE Connectivity HDP-400 Guide de référence

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity 69339 Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity 1213890-1 Guide de référence

TE Connectivity

TE Connectivity CERTI- CRIMP Series Manuel utilisateur

TE Connectivity

TE Connectivity 2063574-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2063490-1 Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity 825508-5 Manuel utilisateur

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity 2031973-1 Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 539 685-2 Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 2-1579016-2 Manuel utilisateur

TE Connectivity

TE Connectivity 90017-3 Manuel utilisateur

TE Connectivity

TE Connectivity 69376 Manuel utilisateur

Manuels Outils de sertissage populaires d'autres marques

Panduit

Panduit CT-1000 Guide de l'administrateur

JST

JST CS 10 Manuel utilisateur

molex

molex 63811-5100 Manuel utilisateur

Danfoss

Danfoss ET4200 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

molex

molex 63825-3000 Manuel utilisateur

Tyco Electronics

Tyco Electronics 69156-1 Manuel utilisateur

CRH

CRH CRL CBLHCT1 Manuel utilisateur

Emerson

Emerson Klauke ES 105CFM Manuel utilisateur

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Mode d’emploi

Danfoss

Danfoss ET4350 Manuel utilisateur

Milwaukee

Milwaukee M18 Manuel utilisateur

HOGERT

HOGERT HT1P169 Manuel utilisateur

Textron

Textron ESG105L Manuel utilisateur

Tyco Electronics

Tyco Electronics 90035-3 Manuel utilisateur

Emerson

Emerson Klauke ES 20RMCCFB Manuel utilisateur

Continental Refrigerator

Continental Refrigerator PC150HD Manuel utilisateur

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuel utilisateur