TE Connectivity HVA280-2P Manuel utilisateur

Instruction Sheet

1 of 4

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

408-35241

5 NOV 2021 Rev A

Figure 1: Crimping die and ferrule locator assembly for HVA280-2P ferrules

Shank

Rear locator

Crimper

Nest

Hold-down

Ferrule locator assembly

1. INTRODUCTION

The crimping die assembly (Figure 1) is designed to be installed into the modular tool holders listed in Table 1.

The crimping die assembly is designed to crimp HVA280-2P ferrules.

Table 1: Part numbers and documents

Crimping die

assembly

Wire range

Terminal part

number

Application

specification

Modular tool

holder

Instruction

sheet

2385674-1

2x4+2x5 mm²

1587723-3

1587724-3

2103171-1

114-32034

2305470-1

408-35048

2326378-1

408-35049

Crimping Die and Ferrule Locator

Assembly for HVA280-2P Ferrules

408-35241

Rev A

2 of 4

2. DESCRIPTION

Each crimping die assembly consists of a crimper, a nest, a hold-down, a rear locator, and a ferrule locator

assembly (as shown in Figure 1).

NOTE

The rear locator and the ferrule locator assembly maintain the ferrule position during the crimping process. The hold-down

maintains the parallelism of the ferrule during the crimping process. They are supplied pre-assembled to the crimping die.

3. INSTALLING THE DIE ASSEMBLY

For information concerning die installation, removal and general performance of each modular tool holder, refer

to the applicable 408 series instruction sheet packaged with the tool holder (Table 1).

DANGER

To avoid personal injury, always disconnect electrical and air supply from the power unit before installing the die assembly

into the tool holder.

To achieve proper orientation of the dies during installation, ensure that the alignment dots are facing in the

direction of the wire clamp on the modular tool holder (Figure 2).

Figure 2: Alignment dots

Alignment dots

Wire clamp

408-35241

Rev A

3 of 4

4. CRIMPING

Strip length and specific crimp information for each terminal being crimped using this die assembly can be

found in the Application Specification referenced in Table 1.

CAUTION

If the tool holder is equipped with a crimp height (fine adjust) adjustment, you can avoid damage to the terminator, modular

tool holder or die assembly by starting at setting A on the crimp disc and incrementally adjusting to the specified crimp height.

If the machine has crimp height/shut height adjustment, refer to the applicable 412 series customer manual for guidance.

1. Insert the properly stripped wire into the ferrule assembly per application specification referenced in

Table 1. Verify that no strands are exposed.

2. Insert the cable lug into the die assembly with the outer ferrule placed on the nest and the shield

placed in the ferrule locator assembly (Figure 3).

3. Close the wire clamp to clamp the wire in place.

4. Cycle the terminator to complete the crimp.

5. Open the wire clamp to remove the crimped assembly from the tooling.

Figure 3: Crimping

5. INSPECTING THE CRIMP

For crimp inspection information, refer to the 114 series application specification referenced in Table 1 for the

ferrule being crimped.

408-35241

Rev A

4 of 4

6. MAINTENANCE AND INSPECTION

Each die assembly is inspected before shipment. When it arrives at your facility, inspect it immediately to

ensure that it was not damaged during shipping.

6.1. Daily maintenance

Make each operator aware of (and responsible for) the following daily maintenance requirements:

Remove dust, moisture, and other contaminants with a clean, soft brush or soft, lint-free cloth. Do not

use objects that could damage the dies.

When the dies are not in use, store them in a clean, dry area.

6.2. Periodic inspection

Regular inspections should be performed by quality control personnel. A record of scheduled inspections

should remain with the dies or be supplied to personnel responsible for the dies. Perform at least one

inspection per month. Base your inspection frequency on the amount of use, ambient working conditions,

operator training and skill, and established company standards. Perform the inspection as follows:

Remove all contaminants with a clean, soft brush or soft, lint-free cloth. Do not use objects that could

damage the dies.

Inspect the crimp area for flattened, chipped, cracked, worn, or broken areas. If damage or abnormal

wear is evident, replace the dies. Refer to Section 7, REPLACEMENT AND REPAIR.

7. REPLACEMENT AND REPAIR

If the dies are damaged or worn excessively, they must be replaced. Order replacement dies through your TE

representative. You can also order parts by any of the following methods:

Go to TE.com and click the Shop TE link at the top of the page.

Call 800-522-6752.

Write to:

CUSTOMER SERVICE (038-035)

TE CONNECTIVITY CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

For customer repair services, call 800-522-6752.

8. REVISION SUMMARY

Revisions to this instruction sheet include:

Initial release

Table des matières

Autres manuels TE Connectivity Outils de sertissage

TE Connectivity

TE Connectivity SDE-SA PN 2063626-1 Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 539 692-2 Manuel utilisateur

TE Connectivity

TE Connectivity 91366- 1 Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity 2368740-1 Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity 46447 Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 539 685-2 Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 2-1579016-2 Manuel utilisateur

TE Connectivity

TE Connectivity 2392945-1 Manuel utilisateur

TE Connectivity

TE Connectivity CERTI-CRIMP 90066-7 Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 0-1579001-3 Manuel utilisateur

TE Connectivity

TE Connectivity 90382- 2 Manuel utilisateur

TE Connectivity

TE Connectivity 90017-3 Manuel utilisateur

TE Connectivity

TE Connectivity 2386893-1 Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 539671-2 Manuel utilisateur

TE Connectivity

TE Connectivity TETRA-CRIMP 59824-1 Manuel utilisateur

TE Connectivity

TE Connectivity 539 726-2 Manuel utilisateur

TE Connectivity

TE Connectivity PDT-48-00 Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA 2391790-1 Manuel utilisateur

TE Connectivity

TE Connectivity AMP 5k/40 CE Manuel utilisateur

TE Connectivity

TE Connectivity 46447 Manuel utilisateur

Manuels Outils de sertissage populaires d'autres marques

Panduit

Panduit CT-1000 Guide de l'administrateur

JST

JST CS 10 Manuel utilisateur

molex

molex 63811-5100 Manuel utilisateur

Danfoss

Danfoss ET4200 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

molex

molex 63825-3000 Manuel utilisateur

Tyco Electronics

Tyco Electronics 69156-1 Manuel utilisateur

CRH

CRH CRL CBLHCT1 Manuel utilisateur

Emerson

Emerson Klauke ES 105CFM Manuel utilisateur

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Mode d’emploi

Danfoss

Danfoss ET4350 Manuel utilisateur

Milwaukee

Milwaukee M18 Manuel utilisateur

HOGERT

HOGERT HT1P169 Manuel utilisateur

Textron

Textron ESG105L Manuel utilisateur

Tyco Electronics

Tyco Electronics 90035-3 Manuel utilisateur

Emerson

Emerson Klauke ES 20RMCCFB Manuel utilisateur

Continental Refrigerator

Continental Refrigerator PC150HD Manuel utilisateur

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuel utilisateur