Tanita KP-601 Manuel utilisateur

Instruction Manual

Read this Instruction Manual carefully and keep for future reference.

Bedienungsanleitung

Lesen Sie sich diese Bedienungsanleitung bitte sorgfältig durch und bewahren Sie sie zum späteren

Nachschlagen auf.

Notice d’utilisation

Veuillez lire avec attention cette Notice d’utilisation et la conserver pour de futures références.

Gebruikershandleiding

Lees deze gebruikershandleiding aandachtig en bewaar hem voor naslagdoeleinden.

Manuale d’istruzione

Leggere questo manuale d’istruzione attentamente e conservarlo per riferimento futuro.

Manual de Instrucciones

Lea este manual de instrucciones cuidadosamente y guárdelo para una futura referencia.

Manual de Instruções

Leia este manual de instruções com atenção e o mantenha para referência futura.

Инструкция по эксплуатации

Внимательно прочтите данную инструкцию по эксплуатации и сохраните ее для будущих обращений.

使用說明書

請詳細閱讀本說明書, 並小心保存. KP6017651 (1)0906FA

This device features radio interference supression in compliance with valid EC Regulation

2004/108/EC.

Dieses Gerät ist funkentstört entsprechend der geltenden EG-Richtlinie 2004/108/EG.

Cet appareil est conforme à la directive 2004/108/CE (compatibilité électromagnétique) en

vigueur.

Questo apparecchio è conforme alla normativa 2004/108/CE vigente in materia di radiodisturbi.

Este aparato tiene supresión antiparasitaria según la directiva CEE vigente 2004/108/CE.

Dit apparaat is storingvrij volgens de geldende EGG richtlijn 2004/108/EG.

Este aparelho caracteriza-se pela supressão de interferência a rádio, em cumprimento ao

Regulamento 2004/108/CE da CE.

Данное устройство соответствует требованиям подавления радиопомех согласно действующей

ЕС-директиве 2004/108/EC.

EC REGULATION 2004/108/EC

This scale is a precision instrument and must be used under certain

conditions to ensure accurate measurement. Please observe the following

when using this scale.

1.Never disassemble the unit.

Use in a vibration-free location that is not exposed to direct sunlight.

3.The scale will not measure accurately in an environment subject to

large temperature and humidity changes. The unit takes approximately

two hours to adjust to such changes.

4.Keep water and chemicals off the scale. Wipe with a damp cloth from

time to time.

Do not use or store near heat sources(ovens, heaters, etc.).

6.When not used for a long time, remove the batteries and store the unit

in a dry, dust-free location.

7.Check and replace batteries before sending the unit for repair. If repair

is necessary, remove the batteries, repack the unit in the original

carton and protect with packing materials before shipment.

8.Do not leave objects on the weighing tray when the scale is not in use.

9.To avoid measurement error, do not measure while using equipment

that generates radio waves, such as mobile phones.

1.To avoid electric shock, do not insert or remove the plug with wet

hands.

2.To avoid electric shock, do not use the equipment near water.

CAUTIONS

WARNING

IMPORTANT

1. Use on a hard ﬂat surface conﬁrming that it is level using the bubble level.

2. To prevent wind from affecting measurement, close cover.

3. Clean using mild detergent. Chemical should not be used.

4. Always use the provided Gem cup.

5. Wait about ﬁve minutes after turning the power on when calibrating.

6. When the display shows a big difference from the test weight after calibration, repeat the

calibration several times.

7. Press TARE if the display doesn't read zero when you remove the object.

8. This scale can be affected by wind, vibration, and temperature changes. If the stable mark

keeps blinking, please use in an area away from those.

9. Close the wind shield when the stable mark isn’t displayed.

NAMES OF PART

1Wind sheild (cover)

2Hinge

3Gem cup

4 LCD display (front)

5 LCD display (back, option)

6 Test weight

7 Open button

8 Lo battery mark

9 Stable mark

0 Minus sign

q Calibration mark

w Weighing modes

e ON/OFF button

r TARE button

t CALIBRATION button

y MODE button

u AC adaptor inlet

i Adjustable feet

o Battery compartment

p USB port (option)

a Level

s AC adapter (option)

d USB cable (option)















RFS



BEFORE USE

When using with batteries

1. Open the battery cover.

2. Remove the battery cover and insert 4 size AA (LR6) batteries.

3. Replace the battery cover.

When using with AC adaptor

1. Do not use any AC adaptor except those with the following speciﬁcation.

*Only use an AC adaptor with a CE marking

2. To use AC adaptor, put the DC jack into the inlet.

◆

Check the level to make sure that the scale is horizontal.◆

Adjust with the

adjustable feet.

Adjust so that the

bubble is the center

circle.

How to remove and attach the cover◆

[How to remove]

Push the hinge to

one side.

Twist and pull it up.

[How to attach]

Insert one side of

hinge.

Twist and pull it

down.

Note: Make sure all 4 feet make contact with surface.

1 2 3 4

1 2 1 2

CALIBRATING

Use the provided 100 g test weight.

Turn the power on.Press the open

button to open the

cover.

The weighting unit

that was used when

the power was

turned off last time

will be displayed.

Default is g.

Set the Gem cup.

Calibration is

complete. Calibration

is not complete when

not showing .

Make sure the stable

mark is displayed.

Press CAL. Remove the test

weight.

When blinks,

place the test weight

gently onto the gem

cup.

WEIGHING

Press OFF.Place the object. Remove it.

1 2 3 4

5 6 7 8

2 3 4

: Overload. The object being weighed exceeds the maximum capacity.

When the scale is on

or : See TROUBLE SHOOTING

TARE FUNCTION

If TARE is pressed in the middle of weighing, zero (0) appears in the display enabling additional

weighing.

Place the object to

be measured on the

scale.

When the stable

mark is on, press

TARE.

SWITCHING UNIT

When the weighing function is available, press the MODE button and the display switches in the

order below.

g →ct →oz →ozt →dwt →grain →HT →TT

1 2

→

COUNTING

When the scale

is on

Press and hold

MODE.

Press CAL. Place 10

specimens to be

weighed.

When stabilized,

a stable mark is

displayed.

Press CAL. The number of

specimens are

displayed.

Place the number

of objects that you

wish to count.

Remove the

objects after

measurement is

ﬁnished.

1 2 3 4 5

6 7 8 9 10

Press ON/OFF to

turn off.

* When the registered weight is insufﬁcient, “PC-25” is displayed. In that case, increase the

number of specimens to 25 pieces. When the stable mark is displayed, press CAL. If the register

is still insufﬁcient, the display changes to show the number of specimens to be increased.

Therefore, increase the number of specimens, and press CAL again. This operation is repeated

until the registered weight becomes 1 g or more. will be displayed when you press CAL if

the registered weight is too low to measure. Numeric numbers change as follows. (Press TARE

to increase the number of specimens)

10 →25 →50 →100 →150 →200 →250 →500

PROGRAMMING AUTO POWER OFF

Default setting is 10 minutes

The auto power off time can be programmed between 0 (= no auto power off) to 60 minutes by

10 minutes increments according to preference.

◆

Press CAL to display

When the power

is off

Press MODE to

conﬁrm

While pressing

MODE press

ON/OFF.

40 30

Wen you have made

your selection, press

MODE to conﬁrm.

The numeric values

are displayed.

Setting is ﬁnished.Press TARE to cycle

through the time

options.

*If the power turns off before appears, the setting is not saved.

1 2 3 4

5 6 7 8

* This scale might have an error within 1% margin when the specimen is

too light.

PROGRAMMING BACKLIT BRIGHTNESS

Press CAL to display

When the power

is off

Press MODE to

conﬁrm.

While pressing

MODE press

ON/OFF.

When you have

made your selection,

press MODE to

conﬁrm.

The numeric values

are displayed.

Setting is ﬁnished.Press the TARE to

cycle through the

backlit options.

BATTERIES REPLACEMENT

When batteries are running low, is displayed. When batteries are running out, is

displayed and the power is automatically turned off.

Immediately replace with new batteries (all 4 batteries). Do not apply excessive force to the

measuring section when replacing batteries.

Default setting is “2”.◆

1 2 3 4

5 6 7 8

TROUBLE SHOOTING

• The power doesn’t turn on.

Insert new 4 size AA (LR6) batteries. Be sure that the polarity of the batteries is set properly.

• or appears on the display.

The scale needs to be repaired. Please contact your retailer.

• appears on the display.

Place the test weight AFTER blinks.

If it doesn't work, the scale needs to be repaired. Please contact your retailer.

• appears on the display.

Place the gem cup BEFORE blinks and do not remove it until calibration is complete.

If it doesn't work, the scale needs to be repaired. Please contact your retailer.

TECHNICAL SPECIFICATIONS

Test weight 100 g (included)

Capacity 100.000 g / 500.00 ct / 3.5273 oz /3.2150 ozt / 64.300 dwt /

1543.25 grain / 2.6717 HT / 2.6666 TT

Graduation 0.002 g / 0.01 ct / 0.0001 oz / 0.0001 ozt / 0.002 dwt / 0.05 grain /

0.0001 HT / 0.0001 TT

Power DC 6V AA (LR06) x 4 (included)

AC adaptor (DC 6V 200 mA) (Option)

Power Consumption

(MAX)

Dual LCD: 45 mA, single LCD: 40 mA

*Not legal for trade

OUTPUT DATA FORMAT (USB verison only)

This section covers the exporting of data from the scale to an external device (e.g. PC) using a

USB compliant signal.

• USB interface is for data OUTPUT ONLY!

• This scale is not capable of receiving instructions from an external device.

• This scale will only output data from 0.04g to 100.00g.

Speciﬁcations

Communications standard USB

Communications method Asynchronous transaction

Signal speed 9600 baud

Data bit length 8 bits

Parity None

Stop bit 1 bit

Terminator CR+LF

Note:

• USB connecter (mini-B-type 4-pin female) is located on the side of the scale.

Caution

If you want to use the USB output, you must install the necessary driver onto your

PC, available to download from http://www.tanita.com

USB Port

Autres manuels pour KP-601

Table des matières

Autres manuels Tanita Échelle

Tanita

Tanita HD-372ftanita Manuel utilisateur

Tanita

Tanita HD-351 Manuel utilisateur

Tanita

Tanita HS-302 Manuel utilisateur

Tanita

Tanita HD-394 Manuel utilisateur

Tanita

Tanita BF-574 Manuel utilisateur

Tanita

Tanita UM-041F Manuel utilisateur

Tanita

Tanita Ironman RD-545IM Manuel utilisateur

Tanita

Tanita UM-072 Manuel utilisateur

Tanita

Tanita BC-730 Manuel utilisateur

Tanita

Tanita UM-028F Manuel utilisateur

Tanita

Tanita DC-430U Manuel utilisateur

Tanita

Tanita WB-380 Manuel utilisateur

Tanita

Tanita BC-1000 Manuel utilisateur

Tanita

Tanita BC-577F Manuel utilisateur

Tanita

Tanita InnerScan BC 545 Manuel utilisateur

Tanita

Tanita KD-192 Manuel utilisateur

Tanita

Tanita Ironman InnerScan BC 548 Manuel utilisateur

Tanita

Tanita UM-028 Manuel utilisateur

Tanita

Tanita BC-G03 Manuel utilisateur

Tanita

Tanita BF-666 Manuel utilisateur

Tanita

Tanita TL-150MA Manuel utilisateur

Tanita

Tanita HD-327 Manuel utilisateur

Tanita

Tanita 1479J Manuel utilisateur

Tanita

Tanita KD-200 Manuel utilisateur

Manuels Échelle populaires d'autres marques

AWS

AWS ZEO-50 Manuel utilisateur

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur

Fidelity Electronics

Fidelity Electronics G2e Manuel utilisateur