T&D RTR500BW Manuel utilisateur
1
RTR500BW RTR-600
Setup Guide
Table of Contents
How the RTR500BW and RTR-600 Series are Used Together .......................................... 2
Getting Ready ..................................................................................................2
Installing the Software......................................................................................................... 2
Base Unit Settings:
Using RTR500BW for Windows......................................................................3
Making Initial Settings for the Base Unit........................................................................... 3
Making Network Settings .................................................................................................... 3
Registering Remote Units.................................................................................................... 4
Installing the Device............................................................................................................. 5
Registering a Base Unit to T&D WebStorage Service .................................7
Remote Unit Settings: Using RTR-600 Settings Utility ................................8
Making Clock and Operational Settings............................................................................. 8
Preparing Item and User Tables for Work Groups ........................................................... 9
Creating Work Group Tables ............................................................................................... 10
Sending Settings to the Remote Unit................................................................................. 11
Data Management and Operation................................................................12
Check Data sent to T&D WebStorage Service ................................................................... 12
Manage Data on PC.............................................................................................................. 13
RTR500BW Specications...............................................................................15
tandd.com
2021. 02 16504390055 (8th Edition)
© Copyright T&D Corporation. All rights reserved.
2
How the RTR500BW and RTR-600 Series are Used Together
RTR500BW is a Base Unit equipped with wired and wireless LAN functionality. It can be
set up to periodically download recorded data from Remote Units (RTR-600 Series) and
automatically send data to a server. Recorded data stored in the server can be viewed
anytime and anywhere on a PC.
Remote Unit
RTR-600 Series
Change
Settings
FTP Server
Repeater
RTR500BC
(if necessary)
Base Unit
RTR500BW
Auto-Download and Sending of Data Save View
Terms used in this Guide
Base Unit RTR500BW
Remote Unit RTR-600 Series
(RTR-602S / 602L / 602ES / 602EL, RTR-601-110 / 601-130 / 601-E10 / 601-E30)
Repeater RTR500BC/ RTR-500 (when used as a Repeater)
Current Readings The most recent measurements recorded by a Remote Unit*
Recorded
Data
Measurements stored in the Remote Unit
*Current Readings are not available on the RTR-600 Series.
Getting Ready
Installing the Software
Download the following software from T&D’s website and install to your computer.
*Do not connect the Base Unit to your computer until the software has been installed.
RTR500BW for Windows
For Base Unit Settings, Network Settings, Remote Unit Registration, etc. (p.3)
tandd.com/software/rtr500bwforwin.html
RTR-600 Settings Utility
For Remote Unit Clock and Operation Settings, Table Settings, Data View, etc. (p.8)
tandd.com/software/rtr600-settings-utility.html
After installation is completed, you will see RTR500BW for Windows and RTR-600 Settings Utility in the Windows
Start Menu.
3
Base Unit Settings:
Using RTR500BW for Windows
Making Initial Settings for the Base Unit
.1
Open RTR500BW for Windows, and then open RTR500BW Settings Utility.
.1
Connect the Base Unit with the supplied AC adaptor to a power source.
.1
Connect the Base Unit with the supplied USB cable to your computer.
• The USB driver installation will start automatically.
• When the USB driver installation is completed, the settings window for your RTR500BW will automatically open.
If the above settings window does not appear automati-
cally:
The USB driver installation may not have been installed correctly.
Please see [Help for Unit Recognition Failure] and check the USB
driver.
.1
Enter the following information in the [Base Unit Settings] window.
Base Unit Name Assign a unique name for each Base Unit.
Connection Password
Enter a password here for connecting to the Base Unit via LAN.
The factory default password is "password".
.1
Check the contents of your selections and click the [Apply] button.
.1
In the settings window under [Clock Settings], click the Current Time column to make
settings in the Base Unit.
.1
Check the contents of your selections and click the [Apply] button.
4
Making Network Settings
.1
In the settings window, from [Network Settings] - [Connection Method], select [Wired LAN]
or [Wireless LAN] .
*Normally, there is no need to change the DHCP settings. Settings can be made according to the network
environment being used.
.1
When using a Wireless LAN:
Make settings for [Wireless LAN SSID], [Security Mode], and [Pre-Shared Key(password)].
*Normally, there is no need to change the Security Mode.
.1
Check the contents of your selections and click the [Apply] button.
The operation will start with the following default settings.
• Recorded Data Transmission*: ON, Transmission Interval: 10 min.
• Current Readings Transmission: ON, Send at 6:00 am every day.
*RTR-600 Series does not support this function.
If you use the RTR500BW with RTR-600 Series only, change the Sending Current Readings setting to OFF.
By default, the settings for Auto Transmission of Recorded Data are as follows.
• Transmission Method: HTTP
• Connection Destination: T&D WebStorage Service
It is possible to change the destination of recorded data to any FTP server. For the setting items in the [FTP
Settings] window, ask the administrator of the FTP server or refer to the instruction manual of the server.
Registering Remote Units
.1
In the [Remote Unit Settings] window, click on the [Register] button.
.1
When the [Connect a Remote Unit] dialog box appears, unplug the USB cable from the
Base Unit (1) and plug it into the Battery Charge Dock*into which the Remote Unit has
been placed (2).
USB
Connection
RTR-600BD
(2)
(1)
*The Battery Charge Dock (RTR-600BD) needs to be purchased separately.
5
If the screen does not change after connecting the Remote Unit:
• Make sure to place the Remote Unit on the right side of the dock as shown above. The left side is for
charging only.
• The USB driver may not have been installed correctly. Please see [Help for Unit Recognition Failure] in
the launcher or Start menu, and check the USB driver.
.1
The [Remote Unit Registration] window will appear. Enter the desired Remote Unit Name
and click [Register].
.1
Follow the on-screen instructions and reconnect the USB cable to the Base Unit.
A success message will appear when the registration is complete.
*If you wish to register other Remote Units, repeat procedures
to
.
Installing the Device
Make sure not to place the Remote Unit on the battery charge dock except when setting or
registering via USB. Otherwise wireless communication may not be possible due to noise.
.1
Connect the Base Unit to the wired or wireless LAN.
*If the target Base Unit is connected to a PC, disconnect the USB cable.
.1
Connect to the power supply using the supplied AC adaptor.
BLINKING ON ON OFF
in about
30 sec...
*You will know network connection was established when <ACTIVE> on the LED changes from blinking to lit.
* If <ACTIVE> and <DIAG> are both blinking, network connection has failed; so please recheck the settings.
.1
Deploy the Base Unit and Remote Unit(s) in the desired locations.
*The wireless communication range, if unobstructed and direct, is about 50 meters.
.1
To check the signal strength between the Base Unit and Remote Unit, from the main
window of RTR500BW Settings Utility, select [Operation] - [Search Network].
.1
In a few seconds, a list of Base Units on the network will appear.
.1
Right click the target Base Unit, and select [Base Unit Settings] in the pop-up menu.
Enter the password and click [OK].
6
.1
In the [Wireless Route Settings] window, click [Test Signal...].
.1
Click [Start] to begin the signal check.
When completed, click [Close]. The result will appear.
How to Read Signal Strength Results
Communication is stable.
Communication is unstable. If communication errors repeatedly occur, reposition the Remote
Unit or add a Repeater.
If no antenna mark appears a communication error has occurred. Try to reposition the
Remote Unit or add a Repeater.
• Please refer to section [Notes and Precautions for Installing Wireless Communication Devices] under
[RTR500B Series Safety Information].
• By using a Repeater, it is possible to extend the wireless communication range. For information about the
Repeater Settings, refer to [Using as a Repeater] in the RTR500BC Getting Started Guide.
7
Registering a Base Unit to
T&D WebStorage Service
The Base Unit collects and sends the Remote Unit’s recorded data to T&D WebStorage
Service automatically when it is set as the destination (default). To check the transmit-
ted data, the Base Unit needs to be registered to T&D WebStorage Service.
.1
Open your browser and log in to T&D WebStorage Service.
https://webstorage-service.com
*If you have not already registered as a User, use the above URL and carry out a New User Registration.
.1
From the screen’s left-side menu, open [Device Settings].
.1
In the upper right of the screen, click on [ Device].
.1
Enter the serial number and registration code for the RTR500BW, then click [Add].
• The serial number and registration code can be found on the supplied Registration Code Label as shown above.
• If you have lost or misplaced the Registration Code Label, you can check it by connecting the Base Unit to your
computer via USB and selecting [Settings Table] - [Base Unit Settings] in the RTR500BW Settings Utility.
• There is no need to register the RTR-600 Series.
• When registration is complete, the registered device will be displayed in a list on the [Device Settings] screen, and it
will be shown to be in waiting for its rst communication.
8
Remote Unit Settings:
Using RTR-600 Settings Utility
Making Clock and Operational Settings
.1
Open RTR-600 Settings Utility.
.1
From the main window, select [Operation] - [Search Network] to search for Base Units on
the network.
.1
Right click on the target Base Unit, and select [Base Unit Settings] in the pop-up menu.
Enter the password and click [OK].
.1
When the [Remote Unit Settings] window appears, select the target Remote Unit and click
[Clock Settings]. Make settings and click [Apply].
.1
To make or change operational settings, select the target Remote Unit, click [Properties],
make settings and click [Apply].
*If necessary, make settings for other Remote Units by repeating procedures
and
.
9
Preparing Item and User Tables for Work Groups
.1
In the main window of RTR-600 Settings Utility, select [Item Table] or [User Table] from
the [File] menu.
Item Table You can create multiple tables and register up to 63 items to be measured in each table.
Upper and lower limits can also be set for each item here.
User Table You can create multiple tables and register up to 62 users in each table.
*Below, the screens and procedures are explained using the Item Table as an example.
.1
Right click in the left side box, and select [Insert Table] from the pop-up menu. Set the
table name.
.1
To make or edit the item list for the inserted table, right click in the right side box and
select from the [Insert Item] or [Delete Item] options. The item name, upper limit and
lower limit can be set here.
• If you don't need to set upper and lower limits, leave them as they are.
.1
Click [Save]. Follow the same steps to make a User Table.
• If you accidentally delete a table, close the window without saving and re-open it to recover the previously saved
settings.
• Clicking [Save] here will not send the table info to the Remote Unit yet.
10
Creating Work Group Tables
Using the above Item and User Tables, it is now possible to create Work Group Tables
according to the operation process.
.1
In the main window of RTR-600 Settings Utility, select [Work Group Table] from the [File]
menu.
.1
Select <Create New...> from the drop-down list at the top of the Work Group Table window.
The <Edit...> option allows
you to rename or delete a
Work Group Table.
.1
In the displayed window, enter a desired name for the Work Group Table and select the
Item Table and User Table to be used. Click [OK].
.1
Select the name of the Work Group Table you just created.
.1
Right click in the left side box and select [Insert Work Group].
Set the work group name.
Autres manuels pour RTR500BW
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels T&D Enregistreur de données
T&D
T&D RTR-501 Manuel utilisateur
T&D
T&D RTR500BW Feuille d'instructions
T&D
T&D RTR-53A Manuel utilisateur
T&D
T&D TR-7wb Series Manuel utilisateur
T&D
T&D TR-71U Manuel utilisateur
T&D
T&D TR71A Manuel utilisateur
T&D
T&D RTR-601 Series Manuel utilisateur
T&D
T&D MCR-4V Manuel utilisateur
T&D
T&D RTR-501 Manuel utilisateur
T&D
T&D TR-7wb Series Manuel utilisateur
T&D
T&D TR41 Manuel utilisateur
T&D
T&D TR-7wf Series Mode d’emploi
T&D
T&D TR41 Manuel utilisateur
T&D
T&D RTR505B Manuel utilisateur
T&D
T&D RTR-505 Manuel utilisateur
T&D
T&D RTR-500DC Manuel utilisateur
T&D
T&D TR-7wf Series Feuille d'instructions
T&D
T&D TR-7wf Series Feuille d'instructions
T&D
T&D RTR-71 Manuel utilisateur
T&D
T&D RTR-505 Manuel utilisateur
