TANDBERG D5018501 Instructions d'utilisation
1 D5018501
Installation of X-Port 10 with Director
This document explains how to connect the X-Port 10 to the Director system. This feature allows easy
connections for an external portable computer and automatic switching between the internal and external
computer with the Director system.
Supplied Components:
• 1 Connector Box
• 1 RS232 Blanking Plate
• 1 Pair of export 10 Mounting Bracket (Left and Right)
• 2 T201-0036 Cables, 1 T201-0072 Cable, 1 T237-0072 Cable, 2 T112-0036 Cables, 1 T323-
0036 Cable, 1 T325-0072 Cable, 1 T324-0036 Cable, 1 T308-0036 Cable, 1 HD15D-Sub to
BNC cable
• 1 TANDBERG Director label
• 4 #10-32 G-style panel nut retainer and 4 #10-32 x ¾” Black rack screw with washer
• 10 Black adhesive cable tie mounting base14 cable ties 4” long
• 2 #4-40 x 3/16” screws
• 1 instruction sheet
RS232 Blanking Plate Installation:
Connector Box Installation:
• Install the blanking plate over the Computer 2
Serial connector located on the rear of the
Smart 3000i projector unit using the 2 supplied
#4-40 x 1/8” screws.
• Install the connector box on the rear of the
Smart 3000i as shown.
• Use the existing screws on the 3000i projector
to fasten the connector box.
• Route the cables through the opening and
connect them as per labels. (See System
Connections)
2 D5018501
RCM or Blank Plate
X-Port 20
X-Port 10 Installation:
DC Power Connection to X-Port 10:
Logo Installation:
Apply the provided TANDBERG Director label to the top right hand corner of the Smart 3000i projector.
The label will help differentiate the type of system you have if and when technical help is required.
• Remove the existing brackets from the X-Port 10
unit and replace them with the supplied left and
right brackets. Use the same screws for mounting
the new brackets.
• Insert the four 10-32 panel nut retainers on the rea
r
left rack mount rail of the 3000i projector. Insert 1
panel nut retainer at the lowest hole, skip 1 hole
insert another, skip 6 holes insert another, skip 1
hole insert another.
• Install the X-Port 10 unit to the exterior of the rac
k
within the 3000i projector. Use the supplied 10-32
x ¾” screws to fasten the X-Port 10.
• Locate the DC power cable supplied with the X-
port 10.
• Remove the Room Control Module (RCM) or the
blank plate and the X-Port 20 panel.
• Connect one end of the DC power cable to the X-
Port 20 through the Room Control Module (RCM)
hole.
• Bring the cable down from the side and connect the
other end of the DC power cable to the X-Port 10
connector labeled as Power Supply.
• Fasten the cable using the supplied tie wraps to
prevent disconnection.
DC Power Connector
3 D5018501
System Connections:
Connect the cables as shown in the diagram below and by matching the cable labeled ends to the
corresponding equipment.
TOUCHSCREEN
TOUCHPANEL CRESNET
MOUSE
PC VGA IN
DISPLAY VGA OUT
AUX CTRL 3
PROGRAMAUX CTRL 2
AUX CTRL 1
LAN
DIAGNOSTICS
INTERNAL
COMPUTER 1
T112-0036
DIRECTOR APPLICATIONS MODULE
RGB OUT
T201-0036
SERIAL
AUD OUT
T308-0036
PROJECTOR
VIDEO
TRAY
PEN
DATA
SPEAKER T324-0036
T112-0036
T201-0036
COMPUTER 1
SERIAL
COMPUTER 1
VIDEO
COMPUTER 1
AUDIO
COMPUTER 2
AUDIO
COMPUTER 2
COMPUTER 2
SERIAL
VIDEO SERIAL
AUD OUT
RGB OUT
NOTES:
T325-0072 EXTERNAL
COMPUTER 2
SMART X-Port 10
CABLE LOOM WITH 3000iREAR INTERFACE PANEL ON 3000i
SEE NOTE 1
1 - CABLE PART OF 3000i
(LABELLED AS RGB 2 IN)
T237-0072
POWER SUPPLY
2 - CABLE SUPPLIED WITH X-PORT 10
SEE NOTE 2
CONNECTS TO X-PORT 20 INTERNAL TO 3000i
Autres manuels TANDBERG Matériel informatique
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
