Tandberg Data DLT7000 Manuel utilisateur
Introduction
About This Manual
Use this manual as a quick reference when operating the Tandberg
DLT7000 tape drive in your system. For additional information, see the
Tandberg DLT7000 Tape Backup System Installation Guide.
Tandberg DLT7000 Front Panel
These control points on the DLT7000 front panel are for operating the drive (Figure 1):
Figure1 DLT7000 Front Panel View
Operation Buttons / Handle
GB
FUNCTION LOCATION COLOR USAGE
Density Select Lower Left Gray Used to override the default density which would normally be
recorded on a tape
Unload Lower Right Gray Used to request the drive to position the tape and allow unload
via cartridge insert / release handle
NOTE: Unload operation can be disabled by the drive applica-
tion software
Cartridge Insert/ Centre Gray Used to load / unload data cartridges
Release Handle
2.6
6.0
10.0/
15.0
20.0
Compress
Density
Override
Select
Write
Protected
Tape in Use
Use
Cleaning
Tape
Operate
Handle
Unload
35.0
Cartridge insert / release handle (down)
Write Protect
(Orange)
Tape in Use
(Yellow)
Use Cleaning
Tape (Yellow)
Operate
Handle
(Green)
Unload
Push Button
Density
Indicators
(Yellow)
Density
Select
Push
Button
Status
Indicators
1442443
Cartridge Door
123
431887-02 23.08.00 15:41 Side 2
LABEL COLOR STATE OPERATING CONDITION
STATUS INDICATOR (right front panel)
Write Protected Orange On Cartridge is write-protected
Off Cartridge is write-enabled
Tape in use Yellow Blinking Cartridge is loaded and the tape is moving.
On Cartridge is loaded; ready for use.
Use Cleaning Yellow On Drive head needs cleaning, or the tape is bad.
Cartridge Remains on after Cleaning tape attempted to clean the drive head, but the tape
you unload the expired, so cleaning was not done.
cleaning cartridge
After cleaning, Problem data cartridge. Try another cartridge.
turns on again
when you reload
the data cartridge
Off Cleaning is complete, or cleaning is unnecessary.
Operate Handle Green On Okay to operate the cartridge/ insert release handle.
Off Do not operate the cartridge insert/release handle.
All four right side On Power-on Selftest is starting.
or all left side Blinking A Power-on Selftest error has occurred. Press the Unload
indicators button or turn drive power off and then on again to clear the
error. If the error remains, call your service representative.
LABEL COLOR STATE OPERATING CONDITION
DENSITY INDICATOR LEFT front panel)
2.6 Yellow On Indicates the tape is recorded in 2.6 GB format.
Blinking Indicates the tape is recorded in another density. You have
selected this density for a write from BOT.
6.0 Yellow On Indicates the tape is recorded in 6.0 GB format.
Blinking Indicates the tape is recorded in another density. You have
selected this density for a write from BOT.
10.0/15.0 Yellow On (default) Indicates the tape is recorded in 10.0 GB format if the DLTtape™III
tape is used.
Blinking Indicates the tape is recorded in15.0 GB format if the DLTtape™IIIxt
tape is used or indicates the tape is recorded in another density.
You have selected this density for a write from BOT.
20.0 Yellow On (default) Indicates the tape is recorded in 20.0 GB format.
Blinking Indicates the tape is recorded in another density. You have selected
this density for a write from BOT.
35.0 Yellow On (default) Indicates the tape is recorded in 35.0 GB format.
Blinking Indicates the tape is recorded in another density. You have selected
this density for a write from BOT.
Compress Yellow On Compression mode enabled. (Compression can be done in 10.0,
15.0, 20.0 and 35.0 GB densities only.)
Off Compression mode disabled.
Density Override Yellow On You have selected a density from the front panel.
Off (default) Density to be selected by the host (automatic).
Blinking You are in density selection mode.
All four right side Blinking A Power-on Selftest error has occurred. Press the Unload button or
or all left side turn drive power off and then on again to clear the error. If the
indicators error remains, call your service representative.
Summary of Front Panel Indicators
Use the following tables to determine the drive’s operating conditions:
431887-02 23.08.00 15:41 Side 3
Indicator Activity During Power-on Selftest
Powering up the system power, the drive performs the power-on selftest (POST). The sequence of
events are:
Result: POST completes in about 15 seconds and the drive responds normally to all commands.
However, it might take longer for the media to become ready. After a bus reset, the tape drive re-
sponds within a bus selection time-out period.
STAGE WHAT HAPPENS
1. The indicators on the right side turn on sequentially, from top to bottom. All indicators stay on for
a few seconds.
2. The indicators on the left side turn on simultaneously for approximately three seconds, and then
turn off.
3. The green Operate Handle indicator, the yellow Use Cleaning Tape indicator, and the orange Write
Protected indicator turn off.
The yellow Tape in Use indicator blinks while the tape drive initializes.
4. After initialization, the drive is in one of the following four states:
DRIVE STATE INDICATOR DISPLAYS AND ACTIONS
1. No cartridge is loaded 1. The yellow Tape In Use indicator is off
2. The green Operate Handle indicator is on
3. The handle is unlatched
4. The drive beeps
You can now raise the handle and insert a cartridge.
2. A cartridge is The drive loads the cartridge. When the yellow Tape In Use indicator stops flashing and
loaded and the stays on, the indicator turns on next to the label of the tape’s native density. For
handle is down example, if the actual tape density is 2.6 GB, then the indicator turns on next to the 2.6
label. You can now select a density. The drive is ready for use.
3. A cartridge is The yellow Tape In Use indicator flashes and turns off. The green Operate Handle
loaded, but the indicator flashes. The handle should then be lowered and the cartridge loads.
handle is up (not
recommended)
4. The drive detects All four right-side or left-side indicators blink repeatedly. You may try to unload the
an error condition tape and reinitialize the drive by pressing the unload button. The indicators stop
blinking and the drive tries to reinitialize.
431887-02 23.08.00 15:41 Side 4
Loading a Cartridge
To load a cartridge into the drive (Figure 2):
1. When the green indicator is on steadily, pull the cartridge insert/release handle open
2. Insert the cartridge
3. Push the cartridge into the drive
4. Push the handle closed
NOTE:
To prevent handle failure, assist the handle to the closed position. Do not flip it.
The green indicator turns off and the yellow indicator blinks to show the tape is loading. When the
tape is at the beginning-of-tape (BOT) marker, the yellow indicator turns on steadily. The tape is now
ready for use.
Figure 2 Loading a Cartridge
431887-02 23.08.00 15:41 Side 5
Unloading a Cartridge
CAUTION!
Always remove the cartridge from the drive before turning off host system power. Failure to remove
a cartridge can result in cartridge and drive damage.
When you remove the cartridge from the drive, return the cartridge to its plastic case to prolong the
cartridge life.
To unload a cartridge from the drive (Figure 3):
1. Press the Unload button (or issue the appropriate system software command). The yellow Tape in
Use indicator blinks as the tape rewinds.
2. When the green indicator turns on (the beeper also sounds), pull the cartridge insert/release hand-
le open to eject the cartridge.
CAUTION!
Immediate extraction of the tape cartridge can lead to tape leader failure. Delay tape cartridge ex-
traction by one to two seconds to avoid this problem.
3. Remove the cartridge.
4. Push the handle closed.
Figure 3 Unloading a Cartridge
431887-02 23.08.00 15:41 Side 6
Cartridge Write-Protect Switch
• The drive may be prevented from writing/recording on the media by enabling the write protect
switch (Figure 4).
Figure 4 Tape Cartridge Write-Protect Switch
Cleaning the Drive
• If the yellow Use Cleaning Tape indicator turns on, unload the data cartridge and load the cleaning
cartridge. The cleaning cartridge automatically cleans the read/write head and unloads when clea-
ning is complete. Be sure to remove the cleaning cartridge when cleaning is complete. Cleaning
cartridges may be purchased from Tandberg Data, ordering no. P/N 43 18 78. The cleaning car-
tridge provides approx. 20 drive cleanings before replacement is necessary.
Operating Hints
• Never operate the cartridge insert/release handle if the green Operate Handle indicator is not on
steadily or blinking, or drive power is off.
• Make sure the cartridge leader is in the correct position; open the cartridge door to inspect the
leader (Figure 5).
Cartridge
leader
Door lock
(Release by lifting door
lock with thumb)
Write-
Protected (left)
Write-
Enabled (right)
Write-Protect
Switch
Orange
Indicator
Figure 5 Tape Cartridge Leader – Correct Position
431887-02 23.08.00 15:41 Side 7
• Insert the cartridge into the drive with a slow, steady motion.
• Do not drop or bang the cartridge. This can displace the tape leader, making the cartridge unusa-
ble and possibly damaging the drive.
• Keep tape cartridges out of direct sunlight and away from heaters and other heat sources.
• Place an identification label only in the slide-in slot on the front of the cartridge.
• Do not adhere labels to a cartridge anywhere except in the slide-in slot.
Tandberg DLT7000 Media Compatibility
NOTE:
The density may only be selected/overridden from BOT (Beginning Of Tape). On tape which already contains
pre-recorded data, the pre-recorded density will automatically be selected by the drive.
STORAGE 70GB* 35GB 40GB* 20GB 30GB* 15GB 20GB* 10GB 6GB 2.6GB
CAPACITY
Hardware Data Yes No Yes No Yes No Yes No No No
Compression
DLTtape™IV Default Override Override Override N/A N/A N/A N/A N/A N/A
DLTtape™IIIXT N/A N/A N/A N/A Default Override N/A N/A N/A N/A
DLTtape™III N/A N/A N/A N/A N/A N/A Default Override Override Override
* Assuming 2:1 data compression – capacity may vary depending on native data.
Default = The density that will be recorded on a blank tape cartridge without an override from either the application software or
from the Density select button.
Override = The lower density that may be selected to be recorded on the tape cartridge from BOT with an override from either the ap-
plication software or from the Density Select button.
431887-02 23.08.00 15:41 Side 8
431887-02 23.08.00 15:41 Side 9
Einführung
Über dieses Handbuch
Benutzen Sie dieses Handbuch als Kurzinformation beim Betrieb des
Tandberg DLT7000-Laufwerks in Ihrem System. Weitere Informationen
finden Sie im Tandberg DLT7000 Tape Backup System Installation
Guide.
Tandberg DLT7000 Vorderansicht
Bitte beachten Sie die folgenden Hinweise für Anzeigen und Bedienungselemente beim Betrieb des
Tandberg DLT7000 (Bild 1):
Bild 1 Tandberg DLT7000 Vorderseite
Bedienungselemente
2.6
6.0
10.0/
15.0
20.0
Compress
Density
Override
Select
Write
Protected
Tape in Use
Use
Cleaning
Tape
Operate
Handle
Unload
35.0
Bedienungsklappe (unten)
Schreibschutz
ein (orange)
Band läuft
(gelb)
Reinigungs-
Cartridge ein-
legen (gelb)
Bedienungs-
klappe betäti-
gen(grün)
Entnahme-
taste
Betriebs-
anzeigen
1442443
FUNKTION PLAZIERUNG FARBE GEBRAUCH
Taste für Aus- unten links grau Zur Änderung der Standardspeicherdichte des Bandes
wahl der
Speicherdichte
Entnehme- unten rechts grau Zum Spulen des Bandes für die anschließende Entnahme durch
taste die Bedienungsklappe
WICHTIG: Die Entnahme kann durch die Anwendungssoftware
gesperrt sein.
Bedienungs- mitte grau Zum Einlegen und Entnehmen der Cartridge
klappe
Cartridge-Schacht
123
D
Anzeige-
leuchten für
Speicher-
dichte (gelb)
Taste für
Auswahl der
Speicher-
dichte
431887-02 23.08.00 15:41 Side 10
Table des matières
Langues :
Autres manuels Tandberg Data Stockage
Tandberg Data
Tandberg Data RDX QuikStation 8 Manuel utilisateur
Tandberg Data
Tandberg Data StorageLoader 2U LTO Manuel utilisateur
Tandberg Data
Tandberg Data StorageLoader DLT VS160 Manuel utilisateur
Tandberg Data
Tandberg Data LTO-1 HH Manuel utilisateur
Tandberg Data
Tandberg Data DLT-V4 Manuel utilisateur
Tandberg Data
Tandberg Data DLT-V4 Manuel utilisateur
Tandberg Data
Tandberg Data DAT320 Manuel utilisateur
Tandberg Data
Tandberg Data STORAGE CAB4000 - Manuel utilisateur
Tandberg Data
Tandberg Data NEO LTO-7 Manuel utilisateur
Tandberg Data
Tandberg Data StorageLibrary T24 LTO Manuel utilisateur
Tandberg Data
Tandberg Data StorageLibrary LTO-3 SCSI Manuel utilisateur
Tandberg Data
Tandberg Data SDLT320 - Manuel utilisateur
Tandberg Data
Tandberg Data STORAGELIBRARY REV2 ONLINE - QUICK Manuel utilisateur
Tandberg Data
Tandberg Data DAT 72 Manuel utilisateur
Tandberg Data
Tandberg Data StorageLibrary T40 T40 Manuel utilisateur
Tandberg Data
Tandberg Data LTO-5 Manuel utilisateur
Tandberg Data
Tandberg Data RDX QuikStor Manuel utilisateur
Tandberg Data
Tandberg Data StorageLoader DLT VS160 Manuel utilisateur
Tandberg Data
Tandberg Data StorageLibrary LTO-3 SCSI Instructions de montage
Tandberg Data
Tandberg Data RDX QuikStor Manuel utilisateur
Manuels Stockage populaires d'autres marques
Spectra Logic
Spectra Logic T-Series Spectra T50e Manuel utilisateur
Panasonic
Panasonic LKM-F931-1 Manuel utilisateur
Tabernus
Tabernus Enterprise Erase E2400 Manuel utilisateur
Rocstor
Rocstor COMMANDER 3F series Manuel utilisateur
HP
HP P9000 Manuel utilisateur
Western Digital
Western Digital Ultrastar Data60 Manuel utilisateur