Synology DS220j Manuel
Synology NAS DS220j
Hardware Installation Guide
Table of Contents
Chapter 1: Before You Start
Package Contents 3
Synology DS220j at a Glance 4
Hardware Specication 5
Safety Instructions 6
Spare Parts 7
Chapter 2: Hardware Setup
Tools and Parts for Component Installation 8
Install Drives 8
Start Up Your Synology NAS 10
LED Indicator Table 11
Chapter 3: System Maintenance
Initial Troubleshooting Guide 12
Chapter 4: Install DSM on Synology NAS
Install DSM with Web Assistant 13
Learn More 13
Synology_HIG_DS220j_20190916
2
Thank you for purchasing this Synology product! Before setting up your new DS220j, please check the package
contents to verify that you have received the items below. Also, make sure to read the safety instructions carefully
to avoid harming yourself or damaging your Synology NAS.
Note: All images below are for illustrative purposes only, and may dier from the actual product.
Package Contents
Main unit x 1 AC power cord x 1
AC power adapter x 1
RJ-45 LAN cable x 1
HDD bracket x 1 Screws for HDD bracket x 3 Screws for hard drives x 10 Screws for xing the
Synology case x 3
Before You Start 1
Chapter
3
3
4Chapter 1: Before You Start
Synology DS220j at a Glance
No. Article Name Location Description
1 Status Indicator
Front Panel
Displays the status of the system. For more information, see "LED Indicator
Table".
2 LAN Indicator Displays the status of the network connection. For more information, see "LED
Indicator Table".
3 Disk Indicator Displays the status of the installed drive. For more information, see "LED
Indicator Table".
4 Power Button
1. Press to power on the Synology NAS.
2. To power o the Synology NAS, press and hold until you hear a beep sound
and the Power LED starts blinking.
5 Fan
Back Panel
Disposes of excess heat and cools the system. If the fan malfunctions, the
Synology NAS will emit a beeping sound.
6 LAN Port Connect a network cable here.
7 USB 3.0 Port Connect external hard drives or other USB devices to the Synology NAS here.
8 Reset Button
1. Press and hold until you hear a beep sound to restore the default IP address,
DNS server, and password for the admin account.
2. Press and hold until you hear a beep sound, then press and hold again until
you hear three beep sounds to return the Synology NAS to “Not Installed”
status so that DiskStation Manager (DSM) can be reinstalled.
9 Kensington
Security Slot Attach a Kensington security lock here.
10 Power Port Connect the AC power adapter here.
5Chapter 1: Before You Start
Hardware Specication
Item DS220j
Compatible Drive Type 3.5" / 2.5" SATA x 2
Maximum Internal Raw Capacity 32TB (2 X 16TB hard drives)
External Ports USB 3.0 x 2
LAN Port 1GbE (RJ-45) x 1
Size (H x W x D) (mm) 165 x 100 x 225.5
Weight (kg) 0.88
Supported Clients • Windows 7 and 10
• Mac OS X 10.11 onward
File Systems • Internal: ext4
• External: ext4, ext3, FAT, NTFS, HFS+, exFAT1
Supported RAID Types • Basic • JBOD • RAID 0 • RAID 1
• Synology Hybrid RAID (1-Disk Fault Tolerance)
Agency Certications • FCC Class B • CE Class B • BSMI Class B
• EAC • VCCI • CCC • RCM • RoHS Compliant
HDD Hibernation Yes
Scheduled Power On/O Yes
Language Localization
Environment Requirements
• Line voltage: 100V to 240V AC
• Frequency: 50/60Hz
• Operating Temperature: 32 to 104°F (0 to 40°C)
• Storage Temperature: -5 to 140˚F (-20 to 60˚C)
• Relative Humidity: 5% to 95% RH
Note: Model specications are subject to change without notice. Please refer to www.synology.com for the latest information.
1The support for exFAT can be enabled after you have purchased and downloaded exFAT Access in Package Center.
6Chapter 1: Before You Start
Safety Instructions
Keep away from direct sunlight and away from chemicals. Make sure the environment does not
experience abrupt changes in temperature or humidity.
Place the product right side up at all times.
Do not place near any liquids.
Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or
aerosol cleaners.
To prevent the unit from falling over, do not place on carts or any unstable surfaces.
The power cord must plug in to the correct supply voltage. Make sure that the supplied AC voltage is
correct and stable.
To remove all electrical current from the device, ensure that all power cords are disconnected from
the power source.
Risk of explosion if battery is replaced with an incorrect type. Dispose of used batteries appropriately.
Tools and Parts for Component Installation
Please prepare the tools and parts below before setting up your Synology NAS:
• A Screwdriver
• At least one 3.5” or 2.5” SATA drive (please visit www.synology.com/compatibility for compatible drive
models)
Warning: If you install a drive that contains data, the system will format the drive and erase all existing data. Please
back up any important data before installation.
Install Drives
1 Push the upper case in the direction as shown below. Lift the upper case and set it aside.
2 Install drives:
• For 3.5” drives with 3 screw holes on each side (indicated below):
a Slide the drive into the hard drive bay, and push it all the way until it’s rmly connected to the SATA
connector.
b Secure the drive with the screws provided.
• For 3.5” drives with 2 screw holes on each side (indicated below):
a Place the HDD bracket on your Synology NAS, and fasten the bracket to the Synology NAS with the
screws provided.
Hardware Setup
8
2
Chapter
9Chapter 2: Hardware Setup
b Slide the drive into the hard drive bay, and push it all the way until it’s rmly connected to the SATA
connector. Secure the drive with the screws provided.
• For 2.5” drives:
a Place the drive in the 2.5" Disk Holder (Type C, sold separately), and then tighten the 2.5" screws to
secure the drive.
b Slide the 2.5" Disk Holder into the hard drive bay, and push it all the way until the drive is rmly connected
to the SATA connector. Secure the Disk Holder with the provided screws.
3 Repeat the steps above to install the other drive if you have prepared one.
4 The position of drives is as follows:
Note: If you want to create a RAID volume, we recommended that all installed drives are of the same size to make
the best use of drive capacity.
10 Chapter 2: Hardware Setup
5 Replace the upper case, and tighten the screws on the back panel.
Start Up Your Synology NAS
1 Connect one end of the AC power adapter to the power port of your Synology NAS. Connect the other end to a
power outlet.
2 Use the LAN cable to connect the Synology NAS to your switch, router, or hub.
3 Press the power button to turn on your Synology NAS.
Congratulations! Your DS220j is now online and detectable from a network computer.
Table des matières
Autres manuels Synology Stockage
Synology
Synology DS-106j Manuel utilisateur
Synology
Synology DiskStation DS410j Manuel utilisateur
Synology
Synology DS620slim Manuel
Synology
Synology USB Station Manuel utilisateur
Synology
Synology DS120j Manuel
Synology
Synology DiskStation DS118 Manuel
Synology
Synology FlashStation FS1018 Manuel
Synology
Synology DiskStation DS218play Manuel
Synology
Synology DiskStation DS112j Manuel utilisateur
Synology
Synology DS223 Manuel utilisateur
Synology
Synology DiskStation Series Manuel utilisateur
Synology
Synology DiskStation DS214 Manuel utilisateur
Synology
Synology DS224+ Manuel utilisateur
Synology
Synology Disk Station DS1010+ Manuel
Synology
Synology RackStation RS814 Manuel utilisateur
Synology
Synology DiskStation DS416play Manuel utilisateur
Synology
Synology DiskStation DS718+ Manuel
Synology
Synology RS1221+ Manuel
Synology
Synology DS109j Manuel utilisateur
Synology
Synology RackStation RS2423RP+ Manuel utilisateur
Manuels Stockage populaires d'autres marques
Spectra Logic
Spectra Logic T-Series Spectra T50e Manuel utilisateur
Panasonic
Panasonic LKM-F931-1 Manuel utilisateur
Tabernus
Tabernus Enterprise Erase E2400 Manuel utilisateur
Rocstor
Rocstor COMMANDER 3F series Manuel utilisateur
HP
HP P9000 Manuel utilisateur
Western Digital
Western Digital Ultrastar Data60 Manuel utilisateur