Swiftech MCW5000-PX Manuel utilisateur

Swiftech Inc., 1703 E. 28th St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769

Parts list

Parts QTY PARTS QTY

MCW5000-PX™ assembly 1 Arctic Alumina Thermal compound 1

Tube inserts 4

Tube removal tool 1

This product is intended for expert users. Please consult with a qualified technician for installation. Improper installation may result in

damage to your components. Swiftech assumes no liability whatsoever, expressed or implied, for the use of these products, nor their

installation. The following instructions are subject to change without notice. Please visit our web site at www.swiftnets.com for updates

1. Before you install the MCW5000-PX™water-block:

a. Prepare two pieces of tubing of sufficient length to connect to

the rest of your circuit. The cuts must be square as shown in figure

1 or leaks may occur:

b. Install the provided plastic tube inserts at each end of the tubes,

as shown in figure 2: these inserts are absolutely imperative when

using any kind of soft tubing, such as vynil, ClearFlex, Taigon, etc...

Square cut

Figure 1 Figure 2

Figure 3

Figure 4

Figure 5

c. Spread a little bit of grease or soap (Vaseline,

dishwashing liquid, etc..) around the tubing. It helps

pushing the tubes in, particularly with Clearflex

tubing, which features a very “sticky” surface.

d. Fully insert both tubes into the fittings. The tip of the plastic tube inserts should

be flush with the inlet and outlet openings, as shown in figure 4 above. Inserting the

tubes requires a firm push, accompanied by a twisting motion.

2. Preparing your Motherboard

 Remove the existing heat sink

 Carefully clean the CPU.

 Lightly coat the CPU with the provided thermal compound. Only a paper-thin coat is necessary. It should be applied using

preferably a razor blade, or a credit card, held between thumb and index at a 45-degree angle.

3. MCW5000-PX™ water-block installation diagram

The MCW5000-PX water-block installs using Intel’s validated retention clips. Please use the retention clips, and

installation guide provided with your motherboard for installation of the water-block onto the CPU.

Page 1 of 2

Swiftech Inc., 1703 E. 28th St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769

4. Connecting the water-block(s) to the cooling circuit.

FAQS:

 Inlet and outlet are interchangeable.

 In Multi-Processor environments, optimal water-block performance will be achieved by connecting them in series (outlet

of one connected to the inlet of the other).

 Recommended coolant: distilled water+ algaecides & corrosion inhibitors are mandatory (automotive antifreeze).

5. Final inspection

Once the installation is completed, it is always a good idea to test the circuit for leaks, prior to powering up the computer.

Troubleshooting help is available on our web site at www.swiftnets.com, or by calling customer support at 562-595-8009.

Note concerning removal of the tubing: Push in collet squarely against face of fitting. A tube removal tool is provided with

the MCW5000 block. With the collet firmly held against the face of the fitting, the tube can be safely pulled out. Do not attempt to pull

the tube out without pushing squarely against the collet. This may result in damaging the fitting. Further details for using quick-connect

fittings are also available here: http://www.johnguest.com/install_6.shtm#disconnect:

Page 2 of 2

Table des matières

Autres manuels swiftech Matériel informatique

swiftech

swiftech MCW5000-PX Manuel utilisateur

swiftech

swiftech MCW5000-P Manuel utilisateur

swiftech

swiftech POLARIS Series Manuel utilisateur

swiftech

swiftech MCW5000-64RH Manuel utilisateur

swiftech

swiftech Stealth Manuel utilisateur

swiftech

swiftech Obsidian Manuel utilisateur

swiftech

swiftech MCX370-A Manuel utilisateur

swiftech

swiftech MCW20-A Manuel utilisateur

swiftech

swiftech Stealth Manuel utilisateur

swiftech

swiftech MCX462+ Manuel utilisateur

swiftech

swiftech MCP35X RESERVOIR Manuel utilisateur

swiftech

swiftech MCW40-T Manuel utilisateur

swiftech

swiftech Maelstrom 5 1/4 Dual Bay Reservoir Series Manuel utilisateur

swiftech

swiftech MCP35B Manuel utilisateur

swiftech

swiftech MCW5000-64 Manuel utilisateur

swiftech

swiftech MCW5000-64 Manuel utilisateur

swiftech

swiftech MCB120 Radbox Manuel utilisateur

swiftech

swiftech MCW82 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur