Swann HD Pro-Series Manuel utilisateur

PRO-SERIES HD

Digital Video Recorder

INSTRUCTION MANUAL

Important Information

FCC Verification

This equipment has been tested and found to comply with the limits for

Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interfer-

ence in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in ac-

cordance with the instructions, may cause harmful interference to radio

or television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

These devices comply with part 15 of the FCC Rules. Operation is sub-

ject to the following two conditions:

• These devices may not cause harmful interference

• These devices must accept any interference received, including in-

terference that may cause undesired operation

Important Notice - All jurisdictions have specific laws and regulations

relating to the use of cameras. Before using any camera for any pur-

pose, it is the buyer’s responsibility to be aware of all applicable laws

and regulations that prohibit or limit the use of cameras and to comply

with the applicable laws and regulations.

FCC Regulation (for USA): Prohibition against eavesdropping

Except for the operations of law enforcement officers conducted under

lawful authority, no person shall use, either directly or indirectly, a de-

vice operated pursuant to the provisions of this Part for the purpose

of overhearing or recording the private conversations of others unless

such use is authorized by all of the parties engaging in the conversation.

Warning - Changes or modifications made to this device not approved

expressly by the party responsible for compliance could void the user’s

authority to operate the equipment.

Important Safety Instructions

• Make sure product is fixed correctly and stable if fastened in place

• Do not operate if wires and terminals are exposed

• Do not cover vents on the back of the device and allow adequate

space for ventilation

• Only use the power adapter supplied with the DVR

Password Information

To ensure your privacy, this device supports password protection. The

default all-access username is admin, the default password is 12345.

To ensure your on-going privacy, we strongly recommend setting a pass-

word as soon as possible. Choose something that you’ll remember, but

that others would be unlikely to guess.

Important Notice - Do not lose or forget your password. To ensure that

your DVR has the best security possible, password recovery has been

designed to be a complicated and time consuming process. Only a select

number of staff at Swann Technical Support Telephone Helpdesk can

assist. Password retrieval can take several days, which means you will

not be able to access your DVR during this time.

Contents

Important Information 2

Contents 3

Chapter 1 - Menu 5

Menu Layout 6

Chapter 2 - Camera Configuration 7

Record: Parameters - Record 8

Record: Parameters - Substream 9

Camera: OSD 10

Camera: Image 11

Camera: Motion 12

Motion Detection Tips 13

Camera: Privacy Mask 14

Camera: Video Tampering 15

Camera: Video Loss 16

Camera: Video Quality Diagnostics 17

Camera: PTZ 18

Camera: PTZ - Creating a Preset 19

Camera: PTZ - Creating a Patrol 20

Camera: PTZ - Creating a Pattern 21

Camera: PTZ - Linear Scan 22

Chapter 3 - Recording Configuration 23

Record: Schedule 24

Record: Advanced 25

Record: Holiday 26

Manual: Record 27

Chapter 4 - Playback 28

Playback: Normal 29

Playback: Event 30

Playback: Tag 31

Playback: Smart 32

Chapter 5 - Export 34

Export: Normal 35

Export: Event 36

Chapter 6 - Configuration 37

Configuration: General - General 38

Configuration: General - DST Settings 39

Configuration: General - More Settings 40

Configuration: Network - Extranet Access 41

Configuration: Network - General 42

Configuration: Network - PPPOE 43

Configuration: Network - NTP 44

Configuration: Network - Email 45

Contents

Configuration: Network - SNMP 46

Configuration: Network - NAT 47

Configuration: Network - More Settings 48

Configuration: Live View - General 49

Configuration: Live View - View 50

Configuration: Exceptions 51

Configuration: User 52

Chapter 7 - System Maintenance 53

System Maintenance: System Info 54

System Maintenance: Log Information 55

System Maintenance: Import/Export 56

System Maintenance: Upgrade 57

System Maintenance: Default 58

System Maintenance: Net Detect 59

System Maintenance: HDD Detect 60

HDD: General 61

HDD: Advanced 62

Manual: Video Quality Diagnostics 63

Warranty Information 64

Helpdesk & Technical Support 65

The Menu is where you control

the various actions and options

that are available on the DVR.

You can also access previous-

ly recorded video for playback

and to export to a USB storage

device such as a flash drive.

To maintain system integrity, a

firmware upgrade can be per-

formed when available and ac-

cess to the Shutdown menu to

restart or safely turn off the

DVR.

26-05-2015 9:30:15 Tue

Camera 02

26-05-2015 9:30:15 Tue

26-05-2015 9:30:15 Tue 26-05-2015 9:30:15 Tue

Camera 01

Camera 03 Camera 04

Menu Layout

Playback: Click this to access all Normal and Motion event recordings.

There are several playback modes to choose from, such as Normal,

Event, Tag and Smart. You can also play video files that have been ex-

ported to a USB storage device such as a flash drive.

Export: Click this to copy or backup footage from the DVR. You’ll need a

compatible USB storage device such as a flash drive to export the data.

Manual: Access manual controls for the recording functions of the DVR.

HDD: Where you’ll be able to access information about and adjust the

settings of your hard drive.

Record: Access recording options, such as quality, resolution, bitrate

and the recording schedule.

Camera: Adjust image settings such as brightness and contrast and

access to Video Quality Diagnostics to alert you to blurred images and

abnormal brightness. Controls for Motion, Privacy Mask and Video Tam-

pering are also available here.

Configuration: Access and configure many settings of the DVR, includ-

ing your network settings, adjusting the time & date and creating or

altering user accounts.

Maintenance: For accessing system information, log information and to

upgrade the firmware.

Shutdown: To shutdown, reboot or log out of the DVR.

To shutdown or reboot the DVR, or

simply log out of the current user ac-

count, click the “Shutdown” button.

To ensure the integrity of your data

and recordings, always select “Shut-

down” when powering off the DVR.

To access the Menu,

right-click the mouse

then select “Menu”.

Hover the mouse cur-

sor over each button to

display a description.

To exit the Menu click

“Exit” or right-click the

mouse.

Camera Configuration

The camera configuration op-

tions are available in the “Re-

cord” and “Camera” menus

that are accessible from the

Menu. You can change the reso-

lution and bitrate as well as im-

age settings for brightness and

contrast. The DVR has several

controls for Motion, Video Tam-

pering, Video Loss and Video

Quality Diagnostics as well as

the ability to apply one or more

masks for privacy.

Camera 01

26-05-2015 9:30:15 Tue

Camera 02

Record: Parameters - Record

Camera: Select a camera that you would like to edit.

Stream Type: By default “Video” is selected. Select “Video & Audio” if

you have an audio source connected to the DVR’s audio input.

Resolution: The default resolution is 1920 x 1080.

Frame Rate: The number of frames per second (fps) that the DVR will

record. The default is 12fps but can be changed to Full Frame when se-

lecting a lower resolution.

Video Quality: The amount of data the DVR will use to record video. Low-

ering the quality reduces the file size of each video saved.

Pre-record: By default the DVR will record 5 seconds before an event

occurs. This reduces the chance of an event not being recorded. We rec-

ommend changing this to 10 seconds (10s).

Post-record: Same as above but the DVR will continue recording after

an event has occurred. 30 seconds (30s) is the recommended length.

Expired Time (day): Determines how long the video footage will remain

on the hard drive without it being overwritten.

Record Audio: Click the checkbox to enable when selecting “Video &

Audio” for the stream type.

• Click the “Restore” button to revert back to default settings.

• Use the “Copy” function to apply all settings to the other cameras.

• Don’t forget to click “Apply” to save settings.

• Click the “Back” button to go back to the Menu.

The Parameters func-

tion allows you to

change the resolution

and bitrate for each

camera connected. By

default the resolution

is 1920 x 1080 which

fits in with the capa-

bilities of the provided

cameras.

Record: Parameters - Substream

Camera: Select a camera that you would like to edit.

Stream Type: By default “Video” is selected. Select “Video & Audio” if

you have an audio source connected to the DVR’s audio input.

Resolution: The default streaming resolution is 352 x 240. You can se-

lect a higher resolution to increase the streaming quality (up to 960 x

480) or you can select a lower resolution (176 x 120 or 320 x 240) if you’re

having issues streaming live video from your DVR to your mobile device

or computer via SwannView Plus.

Frame Rate: The default frame rate for streaming is 30fps for NTSC and

25fps for PAL. You can change this to 12fps or 6fps to reduce the amount

of data required.

Video Quality: The amount of data the DVR will use to stream live video.

Lowering the quality reduces the amount of data required.

• Click the “Restore” button to revert back to default settings.

• Use the “Copy” function to apply all settings to the other cameras.

• Don’t forget to click “Apply” to save settings.

• Click the “Back” button to go back to the Menu.

The Substream menu

gives you control on

how video is streamed

to your mobile device

or computer using the

SwannView Plus app

and Windows software.

You can change the

resolution and bitrate

if you’re having issues

streaming live video

from your DVR.

Camera: OSD

Camera: Select a camera that you would like to edit.

Camera Name: Select a name for the camera you’ve selected. It can be

up to 32 characters in length.

Display Name: This is enabled by default. Click the checkbox if you don’t

want the camera name displayed.

Display Date: This is enabled by default. Click the checkbox if you don’t

want the date displayed.

Display Week: This is enabled by default. Click the checkbox if you don’t

want the day displayed.

Date Format: Select how you would like the date to be displayed.

Time Format: Choose between “12-hour” and “24-hour” time.

Display Mode: Select how you would like the on-screen display to ap-

pear on-screen. It’s worth having a look at the different settings availa-

ble to see what best fits.

OSD Font: Select a different font size for the on-screen display.

Use the mouse to click and drag the display name and date to the de-

sired position.

• Click the “Restore” button to revert back to default settings.

• Use the “Copy” function to apply all settings to the other cameras.

• Don’t forget to click “Apply” to save settings.

• Click the “Back” button to go back to the Menu.

Camera 01

26-05-2015 9:30:15 Tue

Autres manuels pour HD Pro-Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Swann Système de sécurité

Swann

Swann DVR8-4200 Manuel utilisateur

Swann

Swann DVR4-1100 Guide de démarrage rapide

Swann

Swann DVR Guardian SW244-UDC Manuel utilisateur

Swann

Swann 960H Pro series Manuel utilisateur

Swann

Swann RL-0507A Manuel utilisateur

Swann

Swann DVR4-2550 Manuel utilisateur

Swann

Swann SW344-DPS Manuel utilisateur

Swann

Swann SW347-WA2 Manuel utilisateur

Swann

Swann SW212-HXD Manuel utilisateur

Swann

Swann One Outdoor Siren Manuel utilisateur

Swann

Swann SWVAK-834254C Manuel utilisateur

Swann

Swann SWIFI-ISIREN Manuel utilisateur

Swann

Swann SWDVK-840004D Manuel utilisateur

Swann

Swann PLATINUM HD Manuel utilisateur

Swann

Swann SW231PC4 Manuel utilisateur

Swann

Swann SW344-DWD Manuel utilisateur

Swann

Swann DVRx-2500 Manuel utilisateur

Swann

Swann SW351-MDA Manuel utilisateur

Swann

Swann ADW-350 Manuel utilisateur

Swann

Swann Wireless OutdoorCam SW231-WDC Manuel utilisateur

Swann

Swann ADW-340 Manuel utilisateur

Swann

Swann SWA44-D1C2M1 Manuel utilisateur

Swann

Swann Mobile viwer Manuel utilisateur

Swann

Swann SW244-LMP Guide de démarrage rapide

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur

DSC

DSC PC 4010 Manuel du propriétaire