Swann CoreCam Manuel utilisateur

CoreCam®Security Camera

Cámara de seguridad CoreCam®

Caméra de sécurité CoreCamMD

Telecamera di sicurezza CoreCam®

CoreCam®Überwachungskamera

EN Quick Start Guide ES Guía de inicio rápido FR Guide de démarrage rapide

IT Guida rapida DE Schnellstartanleitung

CAMERA OVERVIEW

Threaded screw hole

(attaches to the included wall-mount bracket)

Pull rubber cap gently from the bottom to access:

• ON/OFF switch

• MicroSD card slot

32GB card pre-installed, Max. 128GB card supported

• Micro USB charging port

• Reset button

— Press and hold for 5 seconds to enter pairing mode

— Press and hold for 10 seconds to factory reset the camera

Microphone Speaker

QR code (for

device pairing)

Rubber cap

Passive infrared

motion sensor

LED indicator

Night detection

sensor

Infrared LEDs

(for night vision)

Threaded

mounting post

Bracket screw hole (x3)

Locking knob

GETTING STARTED

Before using the camera for the first time, fully charge it with the included micro USB charging cable.

1Pull open the rubber cap on the bottom of the camera.

2Slide the ON/OFF switch to the ON position Note: You can also charge the camera with the

switch OFF but you won’t be able to check the LED indicator for the charging status.

3Insert the smaller end of the micro USB charging cable into the micro USB port on the camera.

4Insert the other end of the micro USB charging cable into a USB wall charger such as the USB

power adapter for your smartphone.

5The LED indicator on the front of the camera will turn solid blue indicating that the camera is

charging. When the camera is fully charged, the LED indicator will turn off. Actual charging times

may vary depending on the USB power supply (DC5V 2.1A is recommended for faster charging)

and the remaining battery level. A full charge may take up to 6 hours.

6 After charging is finished, unplug the micro USB charging cable from the camera and make sure

to close the rubber cap tightly to keep out water and dust.

The camera comes with a 32GB microSD card pre-installed for recording events and performing

firmware updates. You can easily replace the microSD card with a new one (max. 128GB card

supported), if needed in the future. Simply open the rubber cap on the bottom of the camera, eject

the current microSD card (push in until it clicks) from the microSD card slot, and then insert the new

microSD card (with the label side facing the front of the camera) into the slot until it clicks into place.

You should format the microSD card the first time it is used. From the Swann Security app, go to

Device Settings > [your camera] > Advanced Settings and tap Format.

Charging the camera

Replacing the microSD card

GET THE SWANN SECURITY APP

1Download the latest version of the Swann Security app from the Apple App Store® or Google

Play™ Store on your iOS or Android device. Simply search for "Swann Security".

2Open the app and create your Swann Security account by tapping “Not yet registered? Sign Up” at

the bottom of the screen. Then, activate your Swann Security account by confirming the verification

email that is sent to the registered email address.

Launch the Swann Security app and sign in. Tap the Pair Device button on the screen (or tap the menu

icon in the top left and select “Pair Device”). The app will now guide you through the pairing process

to set up the camera with your Wi-Fi network.

Before you begin, have the camera with you and be close to your router. Please note that the camera

is only compatible with the 2.4GHz network. If your router is using the 5GHz band, please ensure it is

operating in mixed mode.

SET UP THE CORECAM

The camera can be conveniently placed on a table or shelf, or mounted on a flat surface using the

included bracket. Because the camera is completely wire-free, you’ll have a lot of flexibility on where you

can install it. Choose a location with strong, reliable Wi-Fi reception to ensure best video streaming and

battery performance. The easiest way to check is to use your smartphone. Connect your smartphone to

your Wi-Fi network at the spot you have chosen and see if you get 2 bars of Wi-Fi signal or more. As a

general rule, the nearer the camera is to your router, the better the wireless connection quality. If you’re

finding the wireless signal is too weak or out of range, consider installing a Wi-Fi range extender.

CAMERA PLACEMENT

Mounting the bracket

If mounting to a wooden surface, screw

bracket directly to the surface.

If mounting to a masonry surface (brick,

concrete), mark and drill holes, insert wall

plugs, and screw bracket to the surface.

Attaching the camera to the bracket

Screw the threaded hole at the bottom of the

camera onto the threaded post of the bracket

by turning the locking knob clockwise until the

camera is securely attached.

After installation, make sure to

remove the protective plastic film

covering the camera lens.

Adjusting the viewing angle

Loosen the adjustment ring slightly by

turning counter-clockwise. Swivel or tilt

the camera as needed then tighten the

adjustment ring to lock the position.

Have questions?

Visit our Support Center at support.swann.com.You can register your product for dedicated technical

support, find troubleshooting articles, and more. Or email us at any time via: [email protected]

HELP AND RESOURCES

Motion detection

The camera’s PIR motion sensor detects heat signatures of moving objects. You’ll generally get good

detection results by pointing the camera downwards at an angle where people will be moving across

the coverage area before heading directly towards the camera. You can turn motion detection on or off,

as well as adjust the motion detection sensitivity settings using the Swann Security app.

LED indicator guide

The LED light on the front of your camera helps inform you of what is happening with the device.

Swann Security app manual

To better understand the Swann Security App’s interface and features, access the app manual (Menu

> User Manual). You can learn about navigating the various app screens to view live camera stream,

enable 2-way talk, playback recordings, configure modes, check battery level, and more.

Rebooting the camera

On rare occasions, it might be necessary to reboot your camera if it becomes unresponsive. A simple

reboot can also fix connectivity issues quickly. To reboot the camera, open the rubber cap on the

bottom of the camera, slide the ON/OFF switch to the OFF position, wait for 60 seconds, then slide the

ON/OFF switch back to the ON position.

Solid Blue USB Charging

Solid Red Live streaming / Motion recording

Slow Blinking Blue Wi-Fi Pairing mode

Fast Blinking Blue Connecting to Wi-Fi

Infrared LEDs Blinking Firmware update in progress

Table des matières

Autres manuels Swann Caméra de sécurité

Swann

Swann SW-C-HD590 Manuel utilisateur

Swann

Swann Outdoor Cam SW214-ODC Manuel utilisateur

Swann

Swann Professional Security Camera Manuel utilisateur

Swann

Swann MicroCam II Manuel utilisateur

Swann

Swann IP3G1000 Manuel utilisateur

Swann

Swann MEGA FLOOD SW-C-MFC Manuel utilisateur

Swann

Swann BulletCam Manuel utilisateur

Swann

Swann HD-420 Manuel utilisateur

Swann

Swann ALPHA SWA31-C8 Manuel utilisateur

Swann

Swann MicroCam HD Security Camera Manuel utilisateur

Swann

Swann MAXI DAY/NIGHT CAM SR225-4MC-10006 Manuel utilisateur

Swann

Swann SW223-SPR Manuel utilisateur

Swann

Swann ADS-453 QSG Manuel utilisateur

Swann

Swann SWPRO-1080FLB Manuel utilisateur

Swann

Swann HD420 Manuel utilisateur

Swann

Swann Enforcer Manuel utilisateur

Swann

Swann 7090 Manuel utilisateur

Swann

Swann A850 Manuel utilisateur

Swann

Swann SWIFI-2KOCAM-EU Manuel utilisateur

Swann

Swann SWIFI-FLOCAM2 Manuel utilisateur

Swann

Swann PRO-750 Manuel utilisateur

Swann

Swann C-480R Manuel utilisateur

Swann

Swann Advanced ADS-120 Manuel utilisateur

Swann

Swann HD540 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur