SUPPO OSD V3.71 Manuel utilisateur
SUPPO OSD V3.71 10HZ/current sensor
Connetion Pins
Connector’s description
Current
sensor
To the add-on
Current sensor
from SUPPO
RSSI
Connect to your radio receiver’s
RSSI port
Config panel
Connect to
button panel
Main Batt
(to RC plane’s
battery)
Connect to your airplane’s battery
pack (monitor plane’s voltage
Max 28V).
As 11.7v shown on left)
Video In
To you
Camera
Video out
For the OSD video output
GPS
To the GPS
unit supplied
Power in
Connect to power source for your
OSD
(as Voltage 4.5V shown on left)
Configuring OSD:
Press button “Menu”on “Config Panel”to enter system configuration
Use “Option SW”and “Select”button to configure
Button and Light
“Home”
Record home location, Max RSSI,
Clear timer, clear distance value
“Menu”
Enter configuration menu
“Switch”
Switch between configuration options
“Select”
Select each Option’s value
“Reset”
Restart OSD
Signal Light
Off : No power;
On: connecting GPS, waiting for GPS signal;
Flash: working good
Typical FPV with OSD set up:
1. Camera ------- ‘Video in”OSD “Video out”to ---- Suppo V-Tx , video transmitter.
2. Connect GPS, and Main Batt wire to --- RC main battery
3. Connect RSSI to your RC Receiver (Warning: potential dangerous, could damage your
RX. not recommend to do so if you don’t well understand your Radio RX)
4. Connect 9-12V power to Suppo V-tx to power up Suppo V-Tx, OSD and the camera.
Important Notice, care fully check the power wire connect Camera, OSD and Video Tx.
Wrong power wiring could damage your camera OSD and video transmitter.
Important: Never mix up the Video input (VI) wire with the Video output wire (marked VO),
otherwise, it could damage your cam or video transmitter!
System Config menu
description
NTSC ENABLE
0 –Disabled (for PAL)
1 –Enabled (for NTSC)
DISPLAY MODE
0 –Longitude and Latitude
1 –GMT time
Current Sensor
0 –No Current sensor
Will not show any current
infomation
1 –Current sensor connected
Current consumption
information shown
UNIT MODE
0 –Unit at meter (km when
over 10km),
Speed in km/h
1 –display Unit at feet (mile
when over 10mile),
speed in mph
Setting RSSI Min –Max value:
1. On ground power up TX and RX, press “set home”button, OSD will record RSSI
Max;
2. On ground, power off TX, press “Menu”button, OSD will record RSSI Min value.
3. Select Save and Exit to save RSSI Min Max value.
Notes:
GPS first start will take 1 minute. Re-start only 10 second.
Please note that you need to set “HOME”location (press home button) each time to get
the right “Flight Distance”and “Home Distance”, and “Return Course”
Specifications:
Input Volt
Weight
Size
OSD
5-12V
2g
49*33*6.5m
GPS
3.3V
10g
Current Sensor
7-35V, 100A
8g
31*35mm
Power consumption：Max：1.1W
Plane battery detect max 28V
Autres manuels SUPPO Unité de contrôle
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
