Super Circuits PC164C Series Manuel utilisateur
PC164C / PC165 Series Back Focus Procedure
Step 1- Remove Lens Cover
Step 2- If using a C-Mount lenses it can be applied to the camera at this time
Step 3- Most current lenses are CS-Mount and require removal of the C/CS ring
Step 4- To remove the C/CS ring loosen but do not remove completely the two set screws and then remove the C/CS ring.
Step 5- Screw on the CS-Mount lens until a good picture is obtained and tighten the set screws
Step 6- Use the focus ring on the lens to obtain a finer focusing.
Note- If a C-Mount lens was applied and focus could not be obtained, please try the following:
●Ensure that the lens is in fact a C-Mount and not a CS-Mount
●Check the focus adjust on the lens
●If need be loosen the set screws and adjust the position of the lens and C/CS ring as one unit until a good focus is obtained.
WARNING
TO REDUCE THERISK OFFIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE
CAUTION
RISK
OF
ELECTRIC SHOCK
AWA
CAUTION
:
TO REDUCE THE RISK OFELECTRIC SHOCK,
DO NOT REMOVE COVER(0R BACK),
NO USER
-
SERVICEABLE PATRS INSIDE.
REFER SERVICINGTO QUALIFIED SERVICE PERSONNEL
TABLE OF CONTENTS
A. PRECAUTIONS
B. SPECIAL FEATURES
C. APPEARANCE
D. INSTALLATION
E. SPECIFICATION
1.
Do not attempt to disassemble the camera.
There are no user serviceable parts inside. Ask a qualified
service person for servicing.
2.
Handle the camera with care.
Do not abuse the camera. Avoid striking, shaking, etc. Improper
handlingor storagecoulddamage the camera.
6
3.
Do not expose the camera to rain or moisture, or try to
operate it in wet areas.
Turn the power off immediately and ask
a
qualified service
person for servicing. Moisturecan damage the camera.
4.
Do not use strong or abrasive detergents when cleaning
the camera body.
Use a dry cloth to clean the camera when dirty. In case the
dirt is hard to remove, use a mild detergent and wipe gently.
Afterwards, wipe off the remained part of the detergent in it
with a dry cloth.
5.
Clean the CCD faceplate with care.
Do not clean the CCD with strong or abrasive detergents.
Use lens tissue or a cotton tipped applicator and ethanol.
6.
Never face the camera towards the sun.
Do not aim the camera at bright objects. Whether the camera
is in use or not, never aim it at the sun or other extremely bright
objects. Otherwise, blooming or smear may be caused.
7.
Do
notoperate the camerabeyond the specitiedtemperature,
f
humidity or power source ratings.
Use the camera under conditions where temperature is
between
-10°C-+40"C,
and humidity is below
80%.
SPECIAL FEATURES
1
1.
The following functions are built in.
(1)Auto Light Control (ALC)/Electronic Light Control(E/S)
(2)Automatic Gain control (AGC)
(3)Automatic White Balance(AWB)
2.
ConspicuousLow Lux Sensitivityand extremely clear vision.
3. Signal-to-noise ratio of 45dB for colour
&
50dB for B/W
(Equivalent to AGC Off)
4. Horizontal resolution of 380TV lines
&
420
TV lines for Standard
resolution and 480TV lines
&
600
TV lines for High resolution.
5.
Built-in electronic shutter (Auto iris function) and blooming-
free circuit
Built in auto iris functionenablesit to view againststrong light
and add the outlineclearerwith blooming free circuit
6.
OLPF
Built-in for colour version
Unlike usual cameras, this camera filters unnecessary noise
signals in dark view and feedback them with more clear
picture signals.
This makes it possible to eliminate disturbing dark noises in
low lux condition and ensure it to produce an extraordinary
clear picture at any light condition.
BiW
Version
Colour
Version
R
INSTALLATION
1
1.
Mounting
Lens
2.
View of angle and focus adjustment for built in
varifocal lens.
imur
screw
/
Horizontal
T
C
Verltcal
65
5"
33.4"
a,rlance
rcreh
*
Please adjust focus
&
d~stancewith the screws on
the varifocal lens
3.
Cable Connection
4.
Operating Controls and Functions
Colour Version
BIW
Version
a
HOW
TO
INSTALL
THE
AUTO-IRIS LENSCONNECTOR
@I.
Cut off the iris control cable at the edgeof lensconnector and then cut off the
outer cable cover as shown in the diagram.
Ins Control Cable Lens Connector S/l6"(Approx1mately8mm)
Iris Control Cable
@.
Cut off inner cable covers of the iris control cable
as
shown
in
the diagram.
li4"(Approximatly6mm)
6.
Put the heat shnnkable tubes oreauivalenttubes on the innercables
of
the iriscontmlcable.
-
@.
Solderthe inner cablesof the iriscontrol cableat the piin-plug block according to
the
following
1
piassignmentand coverthe heat shrinkabletubes or equivalenttubes over the solderedma
I
and heat on the tubes to shrink them.
n
I
Signal for Video-iris lens
I
I
Signal for DC-iris lens
1
I
Pi
]:Power source:t9V DC,
50mA
Max. Pin I:DAMP-
Pi
2:N.C(Not used)
Pi
2:DAMP+
Pin 3:Video Signal:0.7Vp-p/lOKohms.
Pi
3:DRVt
Pin
4:Shield, ground Pin 4:DRV-(GND)
Rlb
When Auto-iris lens
1s
used. please select
Pln3
,
EIS.
BLC.ALC switch to ALC posltion
p'n'
4,
J
Pl"4
Pl"2
@
Both the connector cover and connector should
be
properly iterlocked
Shrinkable
Tubes
Connector
Note Cut off the
nb
on the connector
Cover
When the lrrs control cable 1s too
w
thsk, connector cover
and
connector
can not
be
interlocked
@Automatic Light Conhol/Electronic Light Control Selector (ALC, E/S)
Let you selectthemode
accnrding
to
the
lens
type
used.
ALC:Select
this
modewhen
an
auto
ins
lens(AU31ens)ii
used
with
this
camera
E8:Select
this
mode
when
atixed
iris
lensor
1
ODC
or
V/D
1)C.Fc.lc.t.t
DC
~f!ou
;ue
u,t~igthe .tlito
In,
Itn, that
require*
n
D€
dn\zugndl
\'11)1'0 Select
\'in
li!ou orc u.tn:thc
.IUIO
In,
Ism that rcqutrc,
:I
\tdcodn\c
\ty.tl
@
DCLevel
DCAuto Iris lens level adjustment
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Super Circuits Caméra de sécurité
Super Circuits
Super Circuits PC2MP-UXP Manuel utilisateur
Super Circuits
Super Circuits CD25IP Manuel utilisateur
Super Circuits
Super Circuits PC813IR Manuel utilisateur
Super Circuits
Super Circuits CD50WR Manuel utilisateur
Super Circuits
Super Circuits 940-GSM4 Manuel utilisateur
Super Circuits
Super Circuits CD23VF Manuel utilisateur
Super Circuits
Super Circuits MVL24KIT Manuel de la liste des pièces
Super Circuits
Super Circuits PC243C5G Manuel utilisateur
Super Circuits
Super Circuits 940-GSM6 Manuel utilisateur
Super Circuits
Super Circuits N8072 Manuel utilisateur
Super Circuits
Super Circuits PC177IR-8 Manuel utilisateur
Super Circuits
Super Circuits 940-GSM Manuel utilisateur
Super Circuits
Super Circuits XTR-BLUE1 Guide de sécurité
Super Circuits
Super Circuits PC269 Manuel utilisateur
Super Circuits
Super Circuits CD23 Manuel utilisateur
Super Circuits
Super Circuits SYRF04 Manuel utilisateur
Super Circuits
Super Circuits CCR-1 Manuel utilisateur
Super Circuits
Super Circuits CD33-2 Manuel utilisateur
Super Circuits
Super Circuits PC33C5G Manuel utilisateur
Super Circuits
Super Circuits PC816VFAC Manuel utilisateur
