Sunmi K2 Manuel du propriétaire
K2
Kiosk User Manual Book
Before using this product, please read this manual carefully and keep it properly.
Please read the internal machine help App for more help or call 400-6666-509 for free telephone services.
The Self-Checkout Kiosk is applicable for the cashier environment of commercial customers in
various industries,such as Chinese and Western catering,high-end department stores,supermarkets,
convenience stores, information sites, interactive multi-media, scenic spot, etc. Please turn on the
Kiosk and search & download the relevant Apps on the App market on Internet.
Wall-mounted
AFloor-standing
BFloor-standing with table
CEco-service expansion
D
Four installation styles of K2 Self-service Kiosk
Quick Setting
After turning on the complete machine power supply, the screen will be lit. Then you will
enter the first boot interface and just simply operate according to the instructions.
There are two types of internet mode available for you.
Wi-Fi setting
Click “Setting” and “WLAN” to enter the WLAN search interface. Wait for the available
WLAN hot spots searching and listing. Click the right WLAN to connect to the network.
Access password is required for an encrypted network connection.
LAN setting
After plugging the network cable correctly, click “Setting” and “Wired Network” to
choose Enable. Access password is required for an encrypted network connection.
As for IP address, there are two options: to automatically obtain IP or to manually
enter IP address.
Only several steps to enable the smart commercial device K2：
Facebook：Sunmitech
LinkedIn：SUNMI Technology
Quick Start Guide
Plug the power line into the power interface.
2
Plug the network cable into the network interface.
3
Close the back plug cover.
4
Press the buttons on both side of the host
at the same time to open the flip panel.
5Press the power switch to turn on the host.
6
Open the back plug cover.
1
2
3
1
5
5
6
Open flip panel
1
1
12
4
3
Press the buttons on both side of the host at
the same time to open the flip panel.
Open paper storage cover
2
Toggle downward the printer driving lever to
open the paper storage cover.
Put in paper
3
Put in the 80mm thermal sensitive paper with a roller
in it and pull out a section outside the printer exit.
Close the paper storage cover and flip panel
4
Press both sides of the paper storage cover to close it.
The printer will automatically cut paper in power on state.
In power off state, it is necessary to manually tear off
excessive paper; Close the flip panel.
Paper Changing Steps for the Inside Printer
Camera used to shoot human face.
Face camera
Touchable screen applied for customer usage.
Touch screen
Used to print receipt.
Printer
Used to read codes.
Code scanner
In standby state, short press to boot, short press
again to be in standby mode;
In service state, long press for 2 to 3 seconds to
choose to shut-down or restart;
In the state of power-on,long press for 11 seconds
to shut down the host.
System switch
Used to control the host power supply.
Host switch
Face camera
Touch screen
Printer
Host switch
Nameplate
System switch
Code scanner
Trumpet
NFC
Indicator light
· Supports reading and writing of M1\ID\CPU card.
NFC
Brief Introduction of Self-Service Kiosk
Wall-mounted
AFloor-standing
BFloor-standing with table
CEco-service expansion
D
Installation Steps of the Four Types of Self-Service Kiosk
Inside the host. Mainboard external interfaces, like USB port,
TF card port, etc, will be exposed after opening it.
Protection cover on the mainboard
Used to cover the face camera inside the host.
Camera maintain cover
A wired network socket.
Wired network interface
Used to plug the power line.
Power interface
Used for external hardware equipment.
USB interface
On the mainboard and used for software update
and debugging.
Micro-USB debug port
Protection cover on the mainboard
Power supply switch
Wired network interface
Camera maintain cover
Micro-USB debug port
USB interface
Power interface
Installation Components
A Wall-mounted: B Floor-standing: C Floor-standing with table: D Eco-service expansion:
Host
1
Mainboard maintain
cover
3
Screw
5
Host back hanger
2
Wall-mounted rack
4
Back plug cover
6
Host
1
Mainboard maintain
cover
3
Stand
5
Host back support
2
Back plug cover
4
Screw
6
Line cover
7Baseplate
8
Mainboard maintain
cover
Stand
Host back support
Back plug cover
Screw
Line cover
Baseplate
Host
1
3
5
2
4
6
Table
7
9
8
Mainboard maintain
cover Back plug cover
Stand
Screw Line cover
Baseplate
Host back supportHost
1
3
5
2
4
Plastic front shell
6
7
9
8
1
1 1 1
2
222
3
333
4
45
5
5
5 6
6
6
8
8
8
99
6
4
4
7
7
7
Drill holes on the wall
1
Drill Ø10 holes according to the height and
spacing described in the reference drawing.
Install the wall-mounted rack
2
Firmly fix the wall-mounted rack on the wall by four M8X50
expansion bolts and four M6X50 expansion screws.
Install the host back hangers
3
Fix the two host back hangers with host by four M6X12 screws;
Plug in the power line and network cable.
A Installation Steps of Wall-mounted
283
280
1130
Hang the host
4
Firmly hang the host back hangers on the
wall-mounted rack.
1
3
45
5
67
8
9
2
Preassemble the stand on the baseplate
1
Preassemble the stand on the baseplate by two
M10X20 screws and do not twist them too tightly.
Fix the stand on the baseplate
2
Twist four M10X20 screws from the bottom of the
plate as shown in the picture and fasten them.
Then fasten the all the screws.
Insert the host back support
3
Insert the host back support into the stand.
Fix the back support with stand
4
Fix the back support with stand by six
M6X12 screws.
Hang the host
5
Hang the host onto the back support.
Fix the back support and host
6
Fix the back support and host by four M6X30 screws.
Assemble the mainboard maintain cover
7
Assemble the mainboard maintain cover onto the host.
Plug lines
8
Plug power line and network cable and cross the lines
through the stand. Fix the back plug cover.
Assemble the line cover
9
Push forward to fix the line cover onto the stand.
B Installation Steps of Floor-standing
Preassemble the table support screws
10
Twist two M6X12 screws into the stand for 5-10 rounds.
Preassemble the table
11
Hang the table support onto the two screws.
Fix the table
12
Fix the table with stand by four M6X12 screws
and fasten all the screws.
Separate the stand
1
Separate the plastic front shell from the metal stand carefully.
Fix the stand on the baseplate
2
Fix the stand on the baseplate by four M10X20 screws.
C Installation Steps of Floor-standing with Table
(The same installation steps of the baseplate, stand and host with the Floor-standing)
D Installation Steps of Eco-service expansion
10
12
1
2
11
Insert host back support
3
Insert the host back support into the stand.
Fix the back support with the stand
4
Fix the back support with the stand by six M6x25 screws.
Fix the plastic front shell
5
Fix the plastic front shell onto the metal stand again by clips.
Fix the host with back support
6
Hang the host onto the back support
and fix them by four M6X25 screws.
Assemble the mainboard maintain cover
7
Fix the mainboard maintain cover on the host.
Plug lines
8
Plug power line and network cable and cross the
lines through the stand. Fix the back plug cover.
Fix the line cover
9
Twist the screws to fix the metal line cover.
3
4
5
67
8
9
Table des matières
Autres manuels Sunmi Terminal tactile
Sunmi
Sunmi T2 LITE Manuel du propriétaire
Sunmi
Sunmi T1 mini Manuel du propriétaire
Sunmi
Sunmi T2SL Manuel utilisateur
Sunmi
Sunmi T2 MINI Manuel du propriétaire
Sunmi
Sunmi BL202 Manuel utilisateur
Sunmi
Sunmi T2 series Manuel du propriétaire
Sunmi
Sunmi V2 PRO T5921 Manuel utilisateur
Sunmi
Sunmi T2 LITE Manuel utilisateur
Sunmi
Sunmi V2 Manuel utilisateur
Sunmi
Sunmi T2s LITE Manuel utilisateur
Manuels Terminal tactile populaires d'autres marques
Wincor Nixdorf
Wincor Nixdorf iPOS plus Advanced Manuel utilisateur
Ingenico
Ingenico AXIUM EX4000 Manuel utilisateur
Heisei Electronics
Heisei Electronics Q-POS 815 Manuel utilisateur
Amano
Amano MTX-15 Manuel utilisateur
FLOWBIRD
FLOWBIRD CWT Compact Touch Manuel utilisateur
Demco
Demco SP7 Manuel utilisateur
