Sundrax DimGate DIN Manuel utilisateur
Contents
2DimGate DIN DMX AC dimmer with four additional 0-10V/1-10V outputs
3
3
3
4
4
4
4
5
6
6
Specifications
General information
Safe operation
Advantages
Installation
Operation
RDM
Connection scheme
Technical maintenance
Notes
3
DMX AC dimmer with four additional 0-10V/1-10V outputs DimGate DIN
Specifications
Control interface
Number of DMX addresses
Controllable output lines
Connectors
Input Voltage
Max current per channel 230 V
Maximum load power
Mains Fuse
Setup
Operating Temperature
IP Rating
Dimensions, mm
DMX512, RDM
8
4 AC and 4 analogue 1-10V/0-10V
Terminal blocks 2EDGVC, 15EDGVC
AC 90-230 V, 50 Hz
10 A
2.4 kW per channel
0.5 A
DIP switchers, RDM
-40...+70°C
IP 20
210(D) x 105(H) x 75(W)
General information
Safe operation
To ensure safe and reliable operation of the devices, please observe the following requirements:
Use the device only for its intended purpose
Do not use devices that show signs of malfunctioning
Avoid strong physical impacts on the device
Protect devices and cables from contact with moisture or other corrosive liquids
Whenever a fault is detected in the device, please contact the manufacturer.
To ensure safe and reliable operation of the devices, please observe
the following requirements:
Use the device only for its intended purpose
Do not use devices that show signs of malfunctioning
Avoid strong physical impacts on the device
Protect devices and cables from contact with moisture or other corrosive liquids
Whenever a fault is detected in the device, please contact the manufacturer.
Warning!
The device uses hazardous
voltage AC 90-250V
4DimGate DIN DMX AC dimmer with four additional 0-10V/1-10V outputs
Operation
DimGate DIN devices start their normal operation in a few seconds after they have been powered up.
Output channels operate according to values receiving from DMX512 port. AC channel 1 corresponds
to DMX start address set by DIP switcher, AC channel 3- to start address+3. 1-10V channel 1 corresponds
to start address+4, 1-10V channel 4- to start address+7. When AC dimmer mode selected, actual level on
AC outputs changes proportionally to DMX value. When AC switcher mode selected, AC channels just
switch the load ON and OFF, DMX value 0-127 switches the load OFF, DMX value 128-255 switches
the load ON.
LED indicator shows the status of input DMX512 signal. If indicator is red, no DMX512 signal detected
on input. If indicator is green, valid DMX512 signal is received. The indicator blinks on change DMX
values controlling device’s outputs.
RDM
Device supports DMX address assignment and dimmer/switcher function changing via RDM.
To select RDM address assignment mode, set all DIP-switcher sections to OFF. In other cases the actual
DMX address will be indicated in RDM parameters anyway.
AC dimmer and AC switcher functions can be selected via RDM by choosing corresponding
“device personality”.
Advantages
Dim AC lines and 1-10V/0-10V lines from one device
Independent phase inputs for dimmable 230V channels
Active analogue 1-10V/0-10V outputs, capable to connect up to 100 drivers/ballasts
Maximum surge protection – power supply optimized for voltage from 100 to 315 V
AC switcher mode
Full galvanic isolation of all ports (except 1-10V)
Warning!
Before mounting and turning
on the power,you need to make
sure protective ground cable
connections and places of their
connection
Installation
1. Ensure the device has no damage caused by transportation
2. Install the device on DIN-rail
3. Connect power supply according to connection scheme
4. Connect DMX512, AC dimming lines, 1-10 outputs according
to connection scheme
5. Connect the grounding circuit to the grounding clamp terminal
6. Set DMX start address on DIP switcher section 1-9. DMX start address is set as binary code where section
1 refers to LSB and section 9- to MSB, ON position- to binary «1», OFF position- to binary «0». Valid address
range from 1 to 504
7. Select the necessary AC channels mode by DIP switcher section 10. Set section 10 to OFF to select
AC dimmer function. Set section 10 to ON to select AC switcher function
8. Apply a MAINS voltage to the terminal «~230V»
5
DMX AC dimmer with four additional 0-10V/1-10V outputs DimGate DIN
Connection scheme
DimGate DIN
FUSE 0.5A L N
ÀÑ 230V
50Hz/0.5A
ADDRESS
DMX/STATUS
D- 0V D+ D- 0V D+
DMX512
+-+-+-+-
1 2 3 4
1-10V CHANNELS
N N
IN OUT
1
IN OUT
2
IN OUT
3
IN OUT
4
N
L/L1
Ballasts/Drivers
with Dimming Control
(interface 1-10V/ 0-10V)
L N
DMX
L/L2 L/L1L/L3
6DimGate DIN DMX AC dimmer with four additional 0-10V/1-10V outputs
Technical maintenance
Maintenance, search and troubleshooting should be performed by service personnel. The device should
be free from dirt, dents, connecting cables and wires must be intact and securely fastened.
Notes
Please send all your warranty-related questions to [email protected]
All Sundrax products are covered by a 36 months warranty.
7
DMX AC dimmer with four additional 0-10V/1-10V outputs DimGate DIN
Sundrax Electronics
6008, First Central 200
2 Lakeside Drive, Park Royal, London
NW10 7FQ United Kingdom
+ 44 (0) 208 991 33 19
www.sundrax.com
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Sundrax Matériel informatique
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
