Sun Microsystems Fire 6800 Manuel utilisateur

Sun Fire™6800 System Hold-down Kit

This document describes how to update the doors and bolt your system to the floor.

Install the Door Supports

1. Unlock and open the cabinet door.

2. Pull down the upper hinge pin, lift the door off the lower hinge pin and remove the door.

Caution – Do not perform Step 3 in the computer room. Drilling the metal door in the computer

room could lead to metal contamination.

3. Drill out the four rivets on the door that secure the door restraint bracket.

Use a number 30 or 1/8-inch drill bit.

4. Secure the new door restraint bracket using the four POP rivets provided. See figure.

The tool to secure the POP rivets is not provided.

Note – This new door restraint provides both vertical and horizontal stability so the cabinet door doesn’t

bend the upper and lower hinge brackets.

5. Reinstall the cabinet door.

6. Repeat Step 1 through Step 5 for the other cabinet door.

Install the Hold Down Brackets

1. Determine mounting hole locations in the site floor.

Optimize system location based on air flow and structural requirements of the operating site. Use the

diagram below for hole location reference.

Caution – Examine site blueprints to ensure that no pipes or wires run beneath the operating

location.

2. Move the system away from the operating location to provide space for drilling.

Note – NEBS Zone 4 earthquake brackets have been tested by Sun Microsystems for installation directly to a

concrete floor. As the performance of connection systems onto reinforced raised floors can vary, a qualified

structural engineer should be consulted prior to installation on a raised floor.

Note – Because each operating location is unique, the bolts that secure the NEBS Zone 4 earthquake bushing

to the site floor must be supplied by personnel at the site. High strength bolts (or alloy threaded rod) with a

maximum diameter of 1/2 inch can be used

Note – Use a vacuum to prevent air contamination in the computer room while drilling.

3. Drill four mounting holes in the site floor in the locations determined in Step 1.

4. Move the system back to the operating location.

16.88 in.

(428.86 mm)22.66 in.

(575.66 mm)

46.00 in.

(1168.6 mm)

44.47 in.

(1129.6 mm)

2.11 in.

(54.0 mm)

2.91 in.

(74.0 mm)

0.51 in.

(13.00 4 PL)

5. Release the catches and remove the kick-panels.

The kick-panels snaps off.

6. Remove the inner and outer kick-panel brackets.

Discard the outer kick-panel brackets. Save the bolts andd the inner kick-panel brackets for Step 7.

7. Place the NEBS Zone 4 earthquake bracket between the new outer kick-panel bracket and the inner

kick-panel bracket and secure the assembly to the cabinet using the existing bolts.

Note – It may be necessary to adjust the cabinet leveling pads to align the NEBS Zone 4 earthquake bracket.

8. Repeat Step 6 and Step 7 for the remaining kick-panel brackets.

Caution – Before you begin drilling examine site blueprints to ensure that no pipes or wires run

beneath operating location.

9. Secure all four bracket assemblies to the floor.

Use a vacuum to prevent air contamination in the computer room while securing the bracket assemblies.

10. Push the kick-panels back into place.

The retainers will snap into place.

NEBS Zone 4

Inner kick-panel bracket

Outer kick-panel bracket

earthquake bracket

Accessing Sun Documentation

You can view, print, or purchase a broad selection of Sun documentation, including localized versions, at:

http://www.sun.com/documentation

Contacting Sun Technical Support

If you have technical questions about this product that are not answered in this document, go to:

http://www.sun.com/service/contacting

Sun Welcomes Your Comments

Sun is interested in improving its documentation and welcomes your comments and suggestions. You can

submit your comments by going to:

http://www.sun.com/hwdocs/feedback

Please include the title and part number of your document with your feedback:

Sun Fire 6800 System Hold-down Kit, part number 817-2664-12

Part No. 817-2664-12, Rev. A

October 2003

Sun Microsystems, Inc.

www.sun.com

suppliers. Portions may be derived from Berkeley BSD systems, licensed from U. of CA. Sun, Sun Microsystems, the Sun logo, and Solaris are trademarks or registered trademarks

of Sun Microsystems, Inc. in the U.S. and in other countries. All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International,

Inc. in the U.S. and in other countries. U.S. Government Rights—Commercial use. Government users are subject to the Sun Microsystems, Inc. standard license agreement and

applicable provisions of the FAR and its supplements.

technologie relative aux polices de caractères, est protégé par un copyright et licencié par des fournisseurs de Sun. Des parties de ce produit pourront être dérivées des systèmes

Berkeley BSD licenciés par l’Université de Californie. Sun, Sun Microsystems, le logo Sun, et Solaris sont des marques de fabrique ou des marques déposées de Sun

Microsystems, Inc. aux Etats-Unis et dans d’autres pays. Toutes les marques SPARC sont utilisées sous licence et sont des marques de fabrique ou des marques déposées de

SPARC International, Inc. aux Etats-Unis et dans d’autres pays.

Autres manuels pour Fire 6800

Table des matières

Autres manuels Sun Microsystems Serveur

Sun Microsystems

Sun Microsystems Fire V210 Manuel de service

Sun Microsystems

Sun Microsystems Enterprise 250 Manuel d'instructions d'installation

Sun Microsystems

Sun Microsystems Sun Fire V20z Manuel utilisateur

Sun Microsystems

Sun Microsystems Ultra Enterprise 450 Manuel de service

Sun Microsystems

Sun Microsystems Netra X1 Manuel de service

Sun Microsystems

Sun Microsystems Fire V440 2-Post Manuel utilisateur

Sun Microsystems

Sun Microsystems Sun Fire X4100 Manuel utilisateur

Sun Microsystems

Sun Microsystems Sun Blade X6250 Manuel utilisateur

Sun Microsystems

Sun Microsystems Netra T1 AC200 Manuel utilisateur

Sun Microsystems

Sun Microsystems Fire V240 Mode d’emploi

Sun Microsystems

Sun Microsystems X3-3L Manuel utilisateur

Sun Microsystems

Sun Microsystems Enterprise 6 00 Series Manuel d'utilisation et d'entretien

Sun Microsystems

Sun Microsystems Sun Fire T1000 Mode d’emploi

Sun Microsystems

Sun Microsystems Sun Fire X2270 Manuel d'installation et d'exploitation

Sun Microsystems

Sun Microsystems Netra ct Manuel utilisateur

Sun Microsystems

Sun Microsystems Sun Fire V890 Manuel utilisateur

Sun Microsystems

Sun Microsystems Netra 240 Manuel utilisateur

Sun Microsystems

Sun Microsystems Sun Fire X2250 Manuel d'installation et d'exploitation

Sun Microsystems

Sun Microsystems Sun Java Content Delivery Server 5.0 Mode d’emploi

Sun Microsystems

Sun Microsystems Netra T1 AC200 Manuel de service

Sun Microsystems

Sun Microsystems SUN FIRE X4500 Manuel utilisateur

Sun Microsystems

Sun Microsystems Netscape Enterprise Server Manuel de service

Sun Microsystems

Sun Microsystems SPARC T5120 Manuel

Sun Microsystems

Sun Microsystems Sun Fire V490 Mode d’emploi

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur