Subaru 2006 Impreza Guide de configuration

ABS (DIAGNOSTICS)

ABS(diag)-2

ABS (DIAGNOSTICS)

Basic Diagnostic Procedure

1. Basic Diagnostic Procedure

A: PROCEDURE

CAUTION:

Remove foreign matters (dust, water, oil, etc.) from the ABSCM&H/U connector during removal and

installation.

NOTE:

•To check harness for broken wires or short circuits, shake trouble spot or connector.

•Refer to “Check List for Interview”. <Ref. to ABS(diag)-4, Check List for Interview.>

Step Check Yes No

1 CHECK PRE-INSPECTION.

1) Ask the customer when and how the trou-

ble occurred using interview checklist. <Ref. to

ABS(diag)-4, Check List for Interview.>

2) Before performing diagnostics, check the

component which might affect ABS problems.

<Ref. to ABS(diag)-8, INSPECTION, General

Description.>

Is the component that might

influence the ABS problem

normal?

Go to step 2. Repair or replace

each unit.

2 CHECK INDICATION OF DTC ON SCREEN.

1) Turn the ignition switch to OFF.

2) Connect the Subaru Select Monitor to data

link connector.

3) Turn the ignition switch to ON and Subaru

Select Monitor power switch to ON.

TE:

If the communication function of the Subaru Se-

lect Monitor cannot be executed normally,

check the communication circuit. <Ref. to

ABS(diag)-19, COMMUNICATION FOR INI-

TIALIZING IMPOSSIBLE, INSPECTION, Sub-

aru Select Monitor.>

4) Read the DTC. <Ref. to ABS(diag)-24,

OPERATION, Read Diagnostic Trouble Code

(DTC).>

5) Record all DTCs and Freeze Frame Data.

Is DTC displayed? Go to step 4. Go to step 3.

3 PERFORM THE GENERAL DIAGNOSTICS.

1) Inspect using “General Diagnostic Table”.

<Ref. to ABS(diag)-77, General Diagnostic

Table. >

2) Perform clear memory mode. <Ref. to

ABS(diag)-17, CLEAR MEMORY MODE,

OPERATION, Subaru Select Monitor.>

3) Perform the inspection mode. <Ref. to

ABS(diag)-25, Inspection Mode.>

4) Read the DTC. <Ref. to ABS(diag)-16,

READ DIAGNOSTIC TROUBLE CODE (DTC),

OPERATION, Subaru Select Monitor.>

Check the DTC does not displayed.

Does the ABS warning light go

off after turning the ignition

switch to ON?

Finish the diagno-

sis.

Check in accor-

dance with “Diag-

nostic Procedure

for ABS”.<Ref.to

ABS(diag)-21, NO

TROUBLE CODE,

INSPECTION,

Subaru Select

Monitor.>

ABS(diag)-3

ABS (DIAGNOSTICS)

Basic Diagnostic Procedure

4 PERFORM THE DIAGNOSIS.

1) Refer to the “List of Diagnostic Trouble

Code (DTC)”. <Ref. to ABS(diag)-34, LIST, List

of Diagnostic Trouble Code (DTC).>

2) Fix the wrong part.

3) Perform clear memory mode. <Ref. to

ABS(diag)-17, CLEAR MEMORY MODE,

OPERATION, Subaru Select Monitor.>

4) Perform the inspection mode. <Ref. to

ABS(diag)-25, Inspection Mode.>

5) Read the DTC. <Ref. to ABS(diag)-16,

READ DIAGNOSTIC TROUBLE CODE (DTC),

OPERATION, Subaru Select Monitor.>

Is DTC displayed? Repeat step 1 to 4

until DTC is not

shown.

Finish the diagno-

sis.

Step Check Yes No

ABS(diag)-4

ABS (DIAGNOSTICS)

Check List for Interview

2. Check List for Interview

A: CHECK

Check the following items about the vehicle’sstate.

1. STATE OF ABS WARNING LIGHT

ABS warning light

comes on.

❏Always

❏Sometimes

❏Only once

❏Not come on

•When / how long does it come on?

Ignition key position ❏LOCK

❏ACC

❏ON (before starting engine)

❏START

❏ON (after Engine starting, engine is running)

❏ON (after Engine starting, engine is at a standstill)

Timing ❏Immediately after turning the ignition to ON

❏Immediately after turning the ignition to START

❏When accelerating —km/h

—MPH

❏When driving at a constant speed km/h MPH

❏When decelerating —km/h

—MPH

❏When turning to the right Steering angle: deg

Steering time: Sec.

❏When turning to the left Steering angle: deg

Steering time: Sec.

❏When operating other electrical parts

•Parts name:

•Operating condition:

ABS(diag)-5

ABS (DIAGNOSTICS)

Check List for Interview

2. STATE OF BRAKE WARNING LIGHT

Brake warning light

comes on.

❏Always

❏Sometimes

❏Only once

❏Not come on

❏When pulling the parking brake lever up.

❏When releasing the parking brake lever down.

•When / how long does it come on?

Ignition key position ❏LOCK

❏ACC

❏ON (before starting engine)

❏START

❏ON (after Engine starting, engine is running)

❏ON (after Engine starting, engine is at a standstill)

Timing ❏Immediately after turning the ignition to ON

❏Immediately after turning the ignition to START

❏When accelerating —km/h

—MPH

❏When driving at a constant speed km/h MPH

❏When decelerating —km/h

—MPH

❏When turning to the right Steering angle: deg

Steering time: Sec.

❏When turning to the left Steering angle: deg

Steering time: Sec.

❏When operating other electrical parts

•Parts name:

•Operating condition:

ABS(diag)-6

ABS (DIAGNOSTICS)

Check List for Interview

3. SYMPTOMS

ABS operating condi-

tion

❏Does not move.

❏Operates only when applying an abrupt brake. Vehicle speed: km/h

MPH

•How to step on brake pedal:

a) Operating time: Sec.

b) Operating noise: ❏Occurs. / ❏Does not occur.

•What kind of noise? ❏Knocking

❏Gong gong

❏Bong

❏Buzz

❏Gong gong buzz

❏Others:

c) Reaction force of brake pedal

❏Stick

❏Weak pedal resistance

❏Strong pedal resistance

❏Others:

Behavior of vehicle a) Directional stability cannot be obtained or the steering refuses to work when applying brakes:

❏Ye s / ❏No

•When: ❏When turning to the right

❏When turning to the left

❏When spinning

❏Others:

b) Directional stability cannot be obtained or the steering refuses to work when accelerating:

❏Ye s / ❏No

•When: ❏When turning to the right

❏When turning to the left

❏When spinning

❏Others:

c) Poor brake performance: ❏Ye s / ❏No

•What kind: ❏Long braking/stopping distance

❏Brakes lock or drag

❏Long pedal stroke

❏Pedal sticks.

❏Others:

d) Poor acceleration: ❏Ye s / ❏No

•What kind: ❏Not accelerate

❏Engine stalls.

❏Others:

e) Occurrence of vibration: ❏Ye s / ❏No

•Where

•What kind:

f) Occurrence of noise: ❏Ye s / ❏No

•Where

•What kind:

g) Other troubles occurred: ❏Ye s / ❏No

•What kind:

ABS(diag)-7

ABS (DIAGNOSTICS)

Check List for Interview

4. CONDITIONS UNDER WHICH TROUBLE OCCURS

Environment a) Weather ❏Fine

❏Cloudy

❏Rainy

❏Snowy

❏Others:

b) Ambient temperature °C(°F)

c) Road ❏Inner city

❏Suburbs

❏Highway

❏Local street

❏Uphill

❏Downhill

❏Paved road

❏Gravel road

❏Muddy road

❏Sandy place

❏Others:

d) Road surface ❏Dried

❏Wet

❏Coveredwithfreshsnow

❏Covered with hardened snow

❏Frozen slope

❏Others:

Condition a) Brakes Deceleration: G

❏Intermittent / ❏Temporary

b) Accelerator Acceleration: G

❏Intermittent / ❏Temporary

c) Vehicle speed km/h MPH

❏Advancing

❏When accelerating

❏When decelerating

❏At low speed

❏When turning

❏Others:

d) Tire inflation pressure Front RH tire: kPa

Front LH tire: kPa

Rear RH tire: kPa

Rear LH tire: kPa

e) Degree of wear Front RH tire:

Front LH tire:

Rear RH tire:

Rear LH tire:

f) Genuine parts are used.: ❏Yes / ❏No

g) Tire chain is attached.: ❏Ye s / ❏No

h) T-type tire is used.: ❏Ye s / ❏No

i) Condition of suspension alignment:

j) Loading state:

k) Repair parts are used.: ❏Yes / ❏No

•Contents:

l) Others:

ABS(diag)-8

ABS (DIAGNOSTICS)

General Description

3. General Description

A: CAUTION

1. SUPPLEMENTAL RESTRAINT SYSTEM

“AIRBAG”

Airbag system wiring harness is routed near the

ABS wheel speed sensor and ABSCM&H/U.

CAUTION:

•Airbag system connectors are colored yel-

low. Do not use the electrical test equipment on

these circuits.

•Be careful not to damage the airbag system

wiring harness when servicing the ABS wheel

speed sensor and ABSCM&H/U.

B: INSPECTION

Before performing diagnosis, check the following

items which might affect ABS problems.

1. BATTERY

Measure battery voltage and check electrolyte.

Standard voltage: 12 V or more

Specific gravity: More than 1.260

2. GROUND

Check the ABS ground (B302) bolt, tightening

torque.

Tightening torque:

13 N

⋅

m (1.3 kgf-m, 9.4 ft-lb)

3. BRAKE FLUID

1) Check the brake fluid level.

2) Check the brake fluid for leaks.

4. HYDRAULIC UNIT

Check the hydraulic unit.

•With brake tester <Ref. to ABS-9, CHECKING

THE HYDRAULIC UNIT ABS OPERATION WITH

BRAKE TESTER, INSPECTION, ABS Control

Module and Hydraulic Control Unit (ABSCM&H/

U).>

•Without brake tester <Ref. to ABS-8, CHECK-

ING THE HYDRAULIC UNIT ABS OPERATION

BY PRESSURE GAUGE, INSPECTION, ABS

Control Module and Hydraulic Control Unit (AB-

SCM&H/U).>

5. BRAKE DRAG

Check for brake drag.

6. BRAKE PAD AND ROTOR

Check the brake pad and rotor.

•FRONT <Ref. to BR-19, INSPECTION, Front

Brake Pad.> <Ref. to BR-21, INSPECTION, Front

Disc Rotor.>

•REAR <Ref. to BR-30, INSPECTION, Rear

Brake Pad.> <Ref. to BR-32, INSPECTION, Rear

Disc Rotor.>

7. TIRE

Check the tire specifications, tire wear and air pres-

sure. <Ref. to WT-2, SPECIFICATION, General

Description.>

ABS(diag)-9

ABS (DIAGNOSTICS)

General Description

C: PREPARATION TOOL

1. SPECIAL TOOL

2. GENERAL PURPOSE TOOL

ILLUSTRATION TOOL NUMBER DESCRIPTION REMARKS

18482AA010

(Newly adopted tool)

CARTRIDGE Troubleshooting for electrical systems.

22771AA030 SUBARU SELECT

MONITOR KIT

Troubleshooting for electrical systems.

TOOL NAME REMARKS

Circuit tester Used for measuring resistance, voltage and amperage.

Oscilloscope Used for measuring sensor.

ST18482AA010

ST22771AA030

ABS(diag)-10

ABS (DIAGNOSTICS)

Electrical Component Location

4. Electrical Component Location

A: LOCATION

(1) ABS control module and hydraulic

control unit (ABSCM&H/U)

(5) Tone wheel (11) Brake and EBD warning light

(6) ABS wheel speed sensor (12) Driver’s control center differential

control module (STI model)

(2) Connector (7) Wheel cylinder

(3) ABS warning light (8) G sensor (13) Yaw rate & lateral G sensor (STI

model)

(4) Data link connector (for Subaru

Select Monitor)

(9) Stop light switch

(10) Master cylinder (14) Transmission control module (AT

model)

ABS00878

(7)

(5)

(3)

(11)

(4)

(2)

(1)

(6)

(5)

(7)

(6)

(5)

(7)

(10)

(9)

(14)

(8)

(6)

(5)

(7)

(13)

(12)

Autres manuels pour 2006 Impreza

Autres manuels Subaru Automobile

Subaru

Subaru Forester 2018 Manuel utilisateur

Subaru

Subaru 2001 IMPREZA Manuel utilisateur

Subaru

Subaru BRZ 2020 Manuel utilisateur

Subaru

Subaru Forester 2018 Manuel utilisateur

Subaru

Subaru 1994 Impreza Manuel utilisateur

Subaru

Subaru 2010 IMPREZA 2.5i Manuel utilisateur

Subaru

Subaru 1998 Impreza Manuel utilisateur

Subaru

Subaru IMPREZA WRX STI 2010 Manuel utilisateur

Subaru

Subaru 2001 Forester Manuel utilisateur

Subaru

Subaru FORESTER 2.5 X L.L.Bean Edition Manuel utilisateur

Subaru

Subaru 2000 Legacy Manuel

Subaru

Subaru XV Crosstrek Manuel utilisateur

Subaru

Subaru Forester 2.5X 2003 Manuel d'installation et d'exploitation

Subaru

Subaru 2001 Forester Manuel utilisateur

Subaru

Subaru Impreza WRX 2012 Manuel utilisateur

Subaru

Subaru 2017 Legacy Manuel utilisateur

Subaru

Subaru Forester 2017 Manuel utilisateur

Subaru

Subaru A3100BE Manuel utilisateur

Subaru

Subaru 2001 Forester Manuel utilisateur

Subaru

Subaru 2001 IMPREZA Manuel utilisateur

Subaru

Subaru Impreza Outback Sport Manuel utilisateur

Subaru

Subaru 2001 Forester Manuel utilisateur

Subaru

Subaru 2004 LEGACY Manuel utilisateur

Subaru

Subaru Outback Manuel utilisateur

Manuels Automobile populaires d'autres marques

Toyota

Toyota 2000 Tundra Manuel utilisateur

CITROËN

CITROËN DS4 DSign Manuel utilisateur

Lexus

Lexus 2015 CT 200h Manuel utilisateur

Cadillac

Cadillac CTS 2008 Manuel utilisateur

Mercedes-Benz

Mercedes-Benz M-class ML 55 AMG Manuel utilisateur

Porsche

Porsche Boxster S Manuel utilisateur

GMC

GMC 2010 Savana 1500 Cargo Manuel utilisateur

KIAM

KIAM SPORTAGE 2014 Manuel de la liste des pièces

GMC

GMC 2013 Terrain Instructions de montage

GMC

GMC T-Series 1999 Manuel utilisateur

Mercury

Mercury 1998 Mystique Manuel utilisateur

Mercury

Mercury 2007 Mariner Manuel utilisateur

Mazda

Mazda 2007 Mazdaspeed 3 Mode d’emploi

Mazda

Mazda 2014 CX-5 Manuel utilisateur

GMC

GMC Chevrolet Express 2022 Manuel utilisateur

GMC

GMC 1997 Jimmy Manuel utilisateur

Chevrolet

Chevrolet 2012 Malibu Manuel utilisateur

Cadillac

Cadillac 2010 Escalade Manuel utilisateur