Sub-Zero WINE STORAGE Manuel utilisateur
Wine Storage Installation Guide
WINE STORAGE
Contents
3Wine Storage
4Model 424G / 424FSG Site Preparation
7Model 424G / 424FSG Installation
11 Model 427G / 427RG Site Preparation
14 Model 427G / 427RG Installation
18 Model WS-30 Site Preparation
25 Model WS-30 Installation
Features and specications are subject to change at any
time without notice. Visit subzero.com/specs for the most
up-to-date information.
Important Note
To ensure this product is installed and operated as safely
and efciently as possible, take note of the following types
of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specied.
IMPORTANT NOTE: Save these instructions for the local
electrical inspector.
subzero.com
|
3
Product Information
Important product information including the model and
serial number are listed on the product rating plate. The
rating plate is located on the underside of the control panel,
on the left. Refer to the illustrations below.
If service is necessary, contact Sub-Zero factory certied
service with the model and serial number. For the name
of the nearest Sub-Zero factory certied service or for
questions regarding the installation, visit the contact & sup-
port section of our website, subzero.com or call Sub-Zero
customer care at 800-222-7820.
WINE STORAGE
Tools and Materials
•Screwdrivers—standard, Phillips and Torx.
•Power drill.
•Drill bits (masonry bits required for concrete installation).
•Standard socket and wrench set.
•2' and 4' levels.
•Material to protect home, ooring and cabinetry during
installation.
Full-size models.
Undercounter models.
RATING PLATE
RATING PLATE
4
|
Sub-Zero Customer Care 800.222.7820
Opening Dimensions
MODEL 424G
MODEL 424G / 424FSG SITE PREPARATION
DUAL INSTALLATION
When installing two units side by side in a dual installa-
tion, the opening width is determined by adding the single
opening widths together.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the nd a
showroom section of our website, subzero.com. For ques-
tions regarding the installation, call Sub-Zero customer care
at 800-222-7820.
OPENING WIDTH W
424G 24" (610)
W
OPENING WIDTH
341/2"
(876)
OPENING
HEIGHT
24" (610)
OPENING
DEPTH
TOP VIEW
SIDE
VIEW FRONT VIEW
subzero.com
|
5
Electrical
Installation must comply with all applicable electrical codes.
The electrical supply should be located within the shaded
area shown in the illustration below. A separate circuit,
servicing only this appliance is required. A ground fault cir-
cuit interrupter (GFCI) is not recommended and may cause
interruption of operation.
IMPORTANT NOTE: The electrical outlet must be placed so
the grounding prong is to the right of the thinner blades.
The outlet must be ush with the back wall.
ELECTRICAL REQUIREMENTS
Electrical Supply 115 VAC, 60 Hz
Service 15 amp
Receptacle 3-prong grounding-type
WARNING
Do not use an extension cord, two-prong adapter or
remove the power cord ground prong.
Preparation
To operate properly, the door must open a minimum of 90°.
Use a minimum 3" (76) ller in corner installations to assure
a 90° door opening.
Uncrate the unit and inspect for damage. Remove and
recycle packing materials. Do not discard the kickplate, anti-
tip bracket, hardware and the leveling legs which hold the
wood base to the bottom of the unit.
MODEL 424G / 424FSG SITE PREPARATION
3" (76)
151/2"
(394)
2"
(51)
LEFT SIDE
OF OPENING
FLOOR
Electrical supply location.
6
|
Sub-Zero Customer Care 800.222.7820
Anti-Tip Bracket
WARNING
To prevent the unit from tipping forward, the anti-tip
bracket must be installed.
MODEL 424G
The anti-tip bracket should be attached to the wall behind
the unit with the bracket ange located 1/4"(6) above the top
of the unit. Refer to the illustration below. Failure to properly
position the anti-tip bracket will prevent proper engagement.
For installations that cannot accommodate the anti-tip
bracket, a countertop bracket is provided to secure the unit
to the countertop. Refer to the illustration below.
1/4"(6)
ANTI-TIP
BRACKET
COUNTERTOP
BRACKET
Anti-tip bracket (424G).
Countertop bracket.
MODEL 424FSG
The back of the anti-tip bracket must be installed 245/8"
(625) from the front and centered behind the unit. Refer to
the illustration below. Refer to page 13 for wood and con-
crete oor applications.
MODEL 424G / 424FSG SITE PREPARATION
ANTI-TIP BRACKET
Anti-tip bracket (424FSG).
subzero.com
|
7
MODEL 424G / 424FSG INSTALLATION
Custom Panel
MODEL 424G
For overlay applications, a custom door panel must be
installed. Panel size is critical for a proper t. To verify panel
requirements and dimensions, refer to the Sub-Zero design
guide at subzero.com/specs.
Finish all sides of the custom panel. They may be visible
when the door is open or through the glass door.
The custom overlay door panel is attached using screws
provided, through the door frame. Screw locations are
marked on the back of the custom panel using tenon cen-
ters inserted into holes of the door frame.
With the unit secured and door closed, hold the custom
panel in desired position on the door. Lightly tap the front
of the panel to locate mounting positions. Remove tenon
centers. Refer to the illustration below.
The door frame has mounting holes to accommodate
Sub-Zero accessory handles. If handle mounting holes are
not utilized, the handle should be attached to the custom
panel prior to mounting. Screw heads may need to be coun-
tersunk into the panel for proper alignment.
To mount the custom panel, open the door and use pre-
drilled holes to position the panel. Drive screws into the
panel through black tape on the door frame. Screw holes
are hidden behind the door gasket. Use as many screws as
necessary to secure the custom panel. Refer to the illustra-
tion below.
Adjustments can be made to the custom panel with a few
mounting screws in place, but not fully tightened. Once the
proper position is achieved, install and secure all screws.
Cover holes on the inside of the door frame with the cover
patches or plugs provided.
CAUTION
A solid panel cannot be installed over the glass door. A
solid door is available through an authorized Sub-Zero
dealer. For local dealer information, visit the nd a
showroom section of our website, subzero.com.
GASKET
GLASS
13/32" (11)
DIAMETER
1/4" (6)
DIAMETER
Tenon center.
Door frame cross section.
DOOR
FRAMEPANEL
TENON CENTER
8
|
Sub-Zero Customer Care 800.222.7820
Alignment
LEVELING
Level the unit before sliding it into position. Turn each of the
four leveling legs clockwise to raise the unit and counter-
clockwise to lower. Refer to the illustration below.
DOOR ADJUSTMENT
The top and bottom cabinet hinges are held in place with
three permanent adjustment screws. For adjustments,
loosen the screws, adjust the door and tighten screws.
Refer to the illustration below. For model 424FSG, only the
bottom door hinge can be adjusted.
Placement
CAUTION
Before moving the unit into position, secure the door
closed and protect any nished ooring.
Use an appliance dolly to move the unit near the opening.
If the unit has been on its back or side, it must stand upright
for a minimum of 24 hours before connecting power.
If the unit will be connected to a home security system,
run lead wires through the compressor compartment prior
to positioning the unit. Refer to page 9. Once the unit is in
position, wiring connection can be completed from the front.
LEVELING LEGS
HINGEADJUSTMENT
SCREW
Leveling.
Door adjustment.
MODEL 424G / 424FSG INSTALLATION
subzero.com
|
9
MODEL 424G / 424FSG INSTALLATION
Completion
Plug the power cord into the grounded outlet, then slide
the unit into position. Verify the anti-tip bracket is properly
engaged.
It may be necessary to install the unit 1/4"(6) beyond the
front surface of adjacent cabinetry, to prevent interference
when the door is opened to 145°. Refer to the full-scale
template on page 10.
HOME SECURITY CONNECTION
If the unit will be connected to a home security system,
make connections to the leads shown in the illustration
below. Refer to the following color codes:
•Normally open contacts—white with red stripe wire.
•Normally closed contacts—white with blue stripe wire.
•Common—gray with white stripe wire.
Use the spade terminals or wire nuts provided to make
proper wiring connections.
CAUTION
The alarm circuit in the unit is intended as a low-
voltage, low-current device only. It should not be used
to switch line power. Any unused terminals should be
completely insulated and all wires should be secured
away from conductive or moving components.
ANCHORING
To anchor, use the countertop bracket provided to secure
the unit to the underside of the countertop. Refer to the
illustration below. If the countertop bracket can not be
utilized, install shims along the top and sides of the unit.
KICKPLATE INSTALLATION
Install the kickplate using the two screws provided. Refer
to the illustration below. The kickplate must be removable
for service. The oor cannot interfere with removal. Do not
cover the louvered section of the kickplate.
COUNTERTOP
BRACKET
KICKPLATE
Anchoring.
Kickplate installation.
HOME SECURITY
LEADS
Home security connection.
10
|
Sub-Zero Customer Care 800.222.7820
MODEL 424G / 424FSG INSTALLATION
DOOR CLOSED
UNDERCOUNTER
UNIT
ADJACENT
CABINETRY
3/4"(19) DOOR PANEL
1/2"
(13)
1/8"(3)
1/4"(6)
HINGE AT 145°
OPENING
(DOOR OPENS PAST 145°)
1" (25)0"
SCALE
145° door opening (top view).
Door Clearance
FULL-SCALE TEMPLATE
To allow for a 145° door opening, the unit should extend
a minimum of 1/4" (6) beyond the front surface of adja-
cent cabinetry. The unit can be installed ush, however,
there is potential for interference with the panel if the
door is opened past 90°.
Autres manuels pour WINE STORAGE
2
Ce manuel convient aux modèles suivants
4
Table des matières
Langues :
Autres manuels Sub-Zero Refroidisseur de vin
Sub-Zero
Sub-Zero 18" Manuel utilisateur
Sub-Zero
Sub-Zero 315W Manuel utilisateur
Sub-Zero
Sub-Zero 427 Manuel utilisateur
Sub-Zero
Sub-Zero Designer Series Manuel utilisateur
Sub-Zero
Sub-Zero 424G Manuel utilisateur
Sub-Zero
Sub-Zero UW24ORH Manuel utilisateur
Sub-Zero
Sub-Zero 424 Manuel utilisateur
Sub-Zero
Sub-Zero Wolf IW Series Manuel utilisateur
Sub-Zero
Sub-Zero ICB424 Manuel du propriétaire
Sub-Zero
Sub-Zero Classic Series Manuel utilisateur
Sub-Zero
Sub-Zero 427 Manuel utilisateur
Sub-Zero
Sub-Zero WS-30 Manuel utilisateur
Sub-Zero
Sub-Zero UW-24 Manuel utilisateur
Sub-Zero
Sub-Zero ICB400 Series Manuel utilisateur
Sub-Zero
Sub-Zero DEU1550B/R Manuel utilisateur
Sub-Zero
Sub-Zero ICBIW-18 Manuel utilisateur
Sub-Zero
Sub-Zero 315W Manuel utilisateur
Sub-Zero
Sub-Zero 424FS Manuel utilisateur
Sub-Zero
Sub-Zero 427RG Mode d’emploi
Sub-Zero
Sub-Zero 427R Instructions d'utilisation
