Sub-Zero 424G Manuel utilisateur

Wine Storage Installation Guide

WINE STORAGE

Contents

3Wine Storage

4Model 424G / 424FSG Site Preparation

7Model 424G / 424FSG Installation

11 Model 427G / 427RG Site Preparation

14 Model 427G / 427RG Installation

18 Model WS-30 Site Preparation

25 Model WS-30 Installation

Important Note

To ensure this product is installed and operated as safely

and efciently as possible, take note of the following types

of highlighted information throughout this guide:

IMPORTANT NOTE highlights information that is especially

important.

CAUTION indicates a situation where minor injury or product

damage may occur if instructions are not followed.

WARNING states a hazard that may cause serious injury or

death if precautions are not followed.

IMPORTANT NOTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise specied.

subzero.com

Product Information

Important product information including the model and

serial number are listed on the product rating plate. For

undercounter models, the rating plate is located on the

underside of the top wall. For full-size models, it is attached

to the underside of the control panel. Refer to the illustra-

tions below.

If service is necessary, contact Sub-Zero factory certied

service with the model and serial number. For the name

of the nearest Sub-Zero factory certied service or for

questions regarding the installation, visit the contact & sup-

port section of our website, subzero.com or call Sub-Zero

customer care at 800-222-7820.

WINE STORAGE

Tools and Materials

tScrewdrivers—standard, Phillips and Torx.

tPower drill.

tDrill bits (masonry bits required for concrete installation).

tStandard socket and wrench set.

t2' and 4' levels.

tMaterial to protect home, ooring and cabinetry during

installation.

Undercounter models.

Full-size models.

RATING PLATE

RATING

PLATE

Sub-Zero Customer Care 800.222.7820

24" (610)

OPENING

DEPTH

24" (610)

OPENING WIDTH

24" (610)

OPENING DEPTH

341/2" (876)

OPENING

HEIGHT

TOP VIEW

FRONT VIEWSIDE VIEW

Opening Dimensions

MODELS 424G AND 424FSG

MODEL 424G / 424FSG SITE PREPARATION

DUAL INSTALLATION

When installing two units side by side in a dual installa-

tion, the opening width is determined by adding the single

opening widths together. A dual installation kit is required,

but does not affect the opening width.

Dual installation kits are available through an authorized

Sub-Zero dealer. For local dealer information, visit the nd a

showroom section of our website, subzero.com. For ques-

tions regarding the installation, call Sub-Zero customer care

at 800-222-7820.

subzero.com

Electrical

Installation must comply with all applicable electrical codes.

The electrical supply should be located within the shaded

area shown in the illustration below. A separate circuit,

servicing only this appliance is required. A ground fault cir-

cuit interrupter (GFCI) is not recommended and may cause

interruption of operation.

IMPORTANT NOTE: The electrical outlet must be placed so

the grounding prong is to the right of the thinner blades.

The outlet must be ush with the back wall.

ELECTRICAL REQUIREMENTS

Power Supply 115 V AC, 60 Hz

Circuit Breaker 15 amp

Receptacle 3-prong grounding-type

WARNING

Do not use an extension cord, two-prong adapter or

remove the power cord ground prong.

FRONT VIEW

151/2"

(394)

3" (76)

2" (51)

LEFT SIDE

OF OPENING

Electrical supply location.

Preparation

To operate properly, the door must open a minimum of 90°.

Use a minimum 3" (76) ller in corner installations to assure

a 90° door opening.

Uncrate the unit and inspect for damage. Remove and

recycle packing materials. Do not discard the kickplate, anti-

tip bracket, hardware and the leveling legs which hold the

wood base to the bottom of the unit.

MODEL 424G / 424FSG SITE PREPARATION

Sub-Zero Customer Care 800.222.7820

Anti-Tip Bracket

WARNING

To prevent the unit from tipping forward, the anti-tip

bracket must be installed.

MODEL 424G

The anti-tip bracket should be attached to the wall behind

the unit with the bracket ange located 1/4"(6) above the top

of the unit. Refer to the illustration below. Failure to properly

position the anti-tip bracket will prevent proper engagement.

For installations that cannot accommodate the anti-tip

bracket, a countertop bracket is provided to secure the unit

to the countertop. Refer to the illustration below.

1/4"(6)

ANTI-TIP

BRACKET

COUNTERTOP

BRACKET

Anti-tip bracket (424G).

Countertop bracket.

MODEL 424FSG

The back of the anti-tip bracket must be installed 245/8"

(625) from the front and centered behind the unit. Refer to

the illustration below. Refer to page 13 for wood and con-

crete oor applications.

MODEL 424G / 424FSG SITE PREPARATION

ANTI-TIP BRACKET

Anti-tip bracket (424FSG).

subzero.com

MODEL 424G / 424FSG INSTALLATION

Custom Panel

MODEL 424G

For overlay applications, a custom door panel must be

installed. Panel size is critical for a proper t. To verify panel

requirements and dimensions, refer to the Sub-Zero design

guide at subzero.com/specs.

Finish all sides of the custom panel. They may be visible

when the door is open or through the glass door.

The custom overlay door panel is attached using screws

provided, through the door frame. Screw locations are

marked on the back of the custom panel using tenon cen-

ters inserted into holes of the door frame.

With the unit secured and door closed, hold the custom

panel in desired position on the door. Lightly tap the front

of the panel to locate mounting positions. Remove tenon

centers. Refer to the illustration below.

The door frame has mounting holes to accommodate

Sub-Zero accessory handles. If handle mounting holes are

not utilized, the handle should be attached to the custom

panel prior to mounting. Screw heads may need to be coun-

tersunk into the panel for proper alignment.

To mount the custom panel, open the door and use pre-

drilled holes to position the panel. Drive screws into the

panel through black tape on the door frame. Screw holes

are hidden behind the door gasket. Use as many screws as

necessary to secure the custom panel. Refer to the illustra-

tion below.

Adjustments can be made to the custom panel with a few

mounting screws in place, but not fully tightened. Once the

proper position is achieved, install and secure all screws.

Cover holes on the inside of the door frame with the cover

patches or plugs provided.

CAUTION

A solid panel cannot be installed over the glass door. A

solid door is available through an authorized Sub-Zero

dealer. For local dealer information, visit the nd a

showroom section of our website, subzero.com.

GASKET

GLASS

13/32" (11)

DIAMETER

1/4" (6)

DIAMETER

Tenon center.

Door frame cross section.

DOOR

FRAMEPANEL

TENON CENTER

Sub-Zero Customer Care 800.222.7820

Alignment

LEVELING

Level the unit before sliding it into position. Turn each of the

four leveling legs clockwise to raise the unit and counter-

clockwise to lower. Refer to the illustration below.

DOOR ADJUSTMENT

The top and bottom cabinet hinges are held in place with

three permanent adjustment screws. For adjustments,

loosen the screws, adjust the door and tighten screws.

Refer to the illustration below. For model 424FSG, only the

bottom door hinge can be adjusted.

Placement

CAUTION

Before moving the unit into position, secure the door

closed and protect any nished ooring.

Use an appliance dolly to move the unit near the opening.

If the unit has been on its back or side, it must stand upright

for a minimum of 24 hours before connecting power.

If the unit will be connected to a home security system,

run lead wires through the compressor compartment prior

to positioning the unit. Refer to page 9. Once the unit is in

position, wiring connection can be completed from the front.

LEVELING LEGS

HINGEADJUSTMENT

SCREW

Leveling.

Door adjustment.

MODEL 424G / 424FSG INSTALLATION

subzero.com

MODEL 424G / 424FSG INSTALLATION

Completion

Plug the power cord into the grounded outlet, then slide

the unit into position. Verify the anti-tip bracket is properly

engaged.

It may be necessary to install the unit 1/4"(6) beyond the

front surface of adjacent cabinetry, to prevent interference

when the door is opened to 145°. Refer to the full-scale

template on page 10.

HOME SECURITY CONNECTION

If the unit will be connected to a home security system,

make connections to the leads shown in the illustration

below. Refer to the following color codes:

tNormally open contacts—white with red stripe wire.

tNormally closed contacts—white with blue stripe wire.

tCommon—gray with white stripe wire.

Use the spade terminals or wire nuts provided to make

proper wiring connections.

CAUTION

The alarm circuit in the unit is intended as a low-

voltage, low-current device only. It should not be used

to switch line power. Any unused terminals should be

completely insulated and all wires should be secured

away from conductive or moving components.

ANCHORING

To anchor, use the countertop bracket provided to secure

the unit to the underside of the countertop. Refer to the

illustration below. If the countertop bracket can not be

utilized, install shims along the top and sides of the unit.

KICKPLATE INSTALLATION

Install the kickplate using the two screws provided. Refer

to the illustration below. The kickplate must be removable

for service. The oor cannot interfere with removal. Do not

cover the louvered section of the kickplate.

COUNTERTOP

BRACKET

KICKPLATE

Anchoring.

Kickplate installation.

HOME SECURITY

LEADS

Home security connection.

Sub-Zero Customer Care 800.222.7820

MODEL 424G / 424FSG INSTALLATION

DOOR CLOSED

UNDERCOUNTER

UNIT

ADJACENT

CABINETRY

3/4"(19) DOOR PANEL

1/2"

(13)

1/8"(3)

HINGE DETENT

AT 145° OPENING

(DOOR OPENS PAST 145°)

1/4"(6)

1" (25)0"

SCALE

145° door opening (top view).

Door Clearance

FULL-SCALE TEMPLATE

To allow for a 145° door opening, the unit should extend

a minimum of 1/4" (6) beyond the front surface of adja-

cent cabinetry. The unit can be installed ush, however,

there is potential for interference with the panel if the

door is opened past 90°.

Autres manuels pour 424G

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Sub-Zero Refroidisseur de vin

Sub-Zero

Sub-Zero Designer Series Manuel utilisateur

Sub-Zero

Sub-Zero ICB424 Manuel utilisateur

Sub-Zero

Sub-Zero ICB424 Manuel utilisateur

Sub-Zero

Sub-Zero WINE STORAGE Manuel utilisateur

Sub-Zero

Sub-Zero WS-30 Manuel utilisateur

Sub-Zero

Sub-Zero Classic Series Manuel utilisateur

Sub-Zero

Sub-Zero WS-30 Manuel utilisateur

Sub-Zero

Sub-Zero WINE STORAGE Manuel utilisateur

Sub-Zero

Sub-Zero ICB424 Manuel utilisateur

Sub-Zero

Sub-Zero ICBIW-18 Manuel utilisateur

Sub-Zero

Sub-Zero 424 Manuel utilisateur

Sub-Zero

Sub-Zero 315W Manuel utilisateur

Sub-Zero

Sub-Zero 427 Manuel utilisateur

Sub-Zero

Sub-Zero 424FS Instructions d'utilisation

Sub-Zero

Sub-Zero 427R Manuel utilisateur

Sub-Zero

Sub-Zero Wolf 400 Series Manuel utilisateur

Sub-Zero

Sub-Zero 430 Manuel utilisateur

Sub-Zero

Sub-Zero IW-18 Manuel utilisateur

Sub-Zero

Sub-Zero 424FS Manuel utilisateur

Sub-Zero

Sub-Zero 427 Manuel utilisateur

Sub-Zero

Sub-Zero Classic CL3050W/O/L Manuel utilisateur

Sub-Zero

Sub-Zero 315W Manuel utilisateur

Sub-Zero

Sub-Zero 427R Manuel utilisateur

Sub-Zero

Sub-Zero 315W Manuel utilisateur

Manuels Refroidisseur de vin populaires d'autres marques

U-Line

U-Line Echelon Wine Captain 2075WC Manuel du propriétaire

Haier

Haier WS50GA Manuel utilisateur

Cavist

Cavist 62 Manuel utilisateur

Kenmore

Kenmore 461.99130 Manuel utilisateur

Miele

Miele KWT 6422 iG Manuel utilisateur

Danby

Danby DWC113BLSDB Manuel utilisateur

Caple

Caple Wi6128 Manuel utilisateur

Avanti

Avanti WC1001 Manuel utilisateur

Frigidaire

Frigidaire FFWC38F6LS Manuel utilisateur

Titan

Titan TT-W2454SZ Manuel d'installation

Klarstein

Klarstein Botella 166 Uno Manuel utilisateur

Costway

Costway FP10130WL Manuel utilisateur

Lemair

Lemair LWC59 Manuel utilisateur

Haier

Haier JC-125GEA Manuel utilisateur

Caple

Caple WCi46B Manuel utilisateur

Climadiff

Climadiff CLI24 Guide rapide

Viking

Viking VCWB301LSS Manuel utilisateur

Caple

Caple WC6511 Manuel utilisateur