Stewart Filmscreen A Electriscreen Manuel utilisateur
Model A Electriscreen
Owner’s Manual
MA-0111
TO THEINSTALLER : BE SURE TO LEAVE THISMANUALWITH TH E OWNER.
•TO THE OWNER
•INSTALLATION INSTRUCTIONS
•OPERATING THE SCREEN
•MAINTENANCE
Printed in U.S.A.
©2000–2011 Stewart Filmscreen Corporation
Stewart Filmscreen reserves the right to make changes to the product specified in this document.
From time to time, this document is updated. Current versions of documentation are posted on the Stewart Filmscreen website at:
www.stewartfilmscreen.com
Contents
To the Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Preparing the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Step 1. Hanging the Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Step 2. Electrical Hook-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operating the Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Adjusting the Screen Extension . . . . . . . . . . . . . . . . . . . . . . . 12
Screen Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Product Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Model A Electriscreen: Owner’s Manual 1
Owner’s Manual
Model A Electriscreen
Congratulations on your purchase of the finest optical viewing screen
available anywhere in the world!
Please take a moment to review this manual, it will help ensure you many
years of trouble-free service from your new S tewart Filmscreen product.
About your Model A Electriscreen
This is one of Stewart’s most popular electric roll up unit s because it can
accommodate screen sizes up to 9’ x 12’ / 180” diagonal (2.7 m x 3.6 m /
4.5m diagonal). Typically, the screen housing is hidden above the ceiling,
and the screen descends through a slot in the ceiling.
Note: This manual refers to “AC” to represent electrical power . Your
location may use 120V, 220V or other electrical power. Screen systems are
manufactured using the electrical power type specified for the location. Use
appropriate power sources for your location.
Preparation
Specifications regarding the individual screen dimensions, weight, mounting
type, and controls are provided by the factory when the unit is ordered.
Before beginning the installation:
Check the specifications for the type of mounting and switch
control to be used.
Ensure that the mounting area and electrical connection are
prepared.
Check the size and weight of the screen to be inst alled so that
you can plan for the number of people required for the mounting
procedure. You need at least two people to mount the smaller
screens; more are needed for larger, heavier screens.
2Stewart Filmscreen Corporation
TO THE OWNER
PREPARING THE INSTALLATION
Before proceeding with the installation of this screen,
be sure to thoroughly read and underst and all the
installation and operating instructions.
All electrical wiring installations must conform to local
and national codes and should be performed by
qualified service personnel.
There are no user-serviceable parts contained within the
unit.
You will need:
Enough ladders for the personnel supporting the screen during
the mounting process
A level
Fasteners appropriate for the surface on which the screen is
being mounted
Unpacking
1. Remove the outer plastic covering and white wrapping paper
surrounding the screen case.
2. Do not remove the wrapping paper surrounding the screen roller.
You should remove it only af ter the unit is hung and all electrical
connections have been made.
3. Remove the batten lock-down screws located on the back side of
the case.
Model A Electriscreen: Owner’s Manual 3
Warning!
Failure to remove the batten lock-down screws can result in
permanent damage to the screen.
Factory Advisory
The factory advises against installing a concealed or recessed
electrical projection screen permanently. You must be able to
access and remove the unit should future service be
necessary.
Suggested solutions for removing the unit include:
A removable ceiling cover plate under the mounting
location
Access to the unit through an attic or overhead space
Caution
During installation, do not place the unit on an unst able cart,
stand, table, or ladder. The unit may fall, causing injury to a
child or adult and damage to the unit.
Professional mounting techniques should be used. Stewart Filmscreen
Corporation cannot be liable for substandard or faulty installations.
Make sure that you mount the screen so that the electrical box is on the left
side (audience left).
Wall installation
1. Mount screen through the holes in the wall mount brackets.
Refer to Figure 1.
– If mounting onto a wood substructure, #12 screws may be used.
– If the unit is to be mounted to plaster , drywall, masonry, or other-
type of surface, use an appropriate fastener . (These might include
toggle or molly bolts or similar fasteners.)
2. Make sure the unit is level.
Ceiling or top mount installation
The Model A Electriscreen can be installed into the ceiling or sof fit. A false
ceiling is not intended to support the weight of a Model A Electriscreen.
Make sure that you mount the screen so that the electrical box is on the left
side (audience left). Refer to Figure 2.
If the unit is to be mounted to plaster, drywall, masonry, or other type of
surface, use an appropriate fastener. (These might include toggle or molly
bolts or similar fasteners.)
There are two types of ceiling or top mount: suspended or flush to ceiling.
Follow the procedure for the specified type of mounting.
4Stewart Filmscreen Corporation
Figure 2: Ceiling or top mount
STEP 1. HANGING THE CASE
Figure 1: Wall mount using
optional brackets
Electrical
Knockout
Electrical
Box Access
Plate
Screen
Suspended installation
1. Suspend the unit from the holes on the plate using chains,
cables, Unistrut, threaded rod, or turnbuckles. Refer to Figure 3.
2. Make sure the unit is level.
Flush to ceiling mount (optional)
You can install the screen so that the top of the unit is flush with the ceiling.
Note: When the flush to ceiling mount option is ordered, mounting brackets
(also called doctor brackets) are pre-mounted on the ends of the screen
case.
1. Mount screen through the holes in the brackets.
Refer to Figure 4.
2. Make sure the unit is level.
Model A Electriscreen: Owner’s Manual 5
Figure 4: Flush to ceiling
mount
Figure 3: Suspended
installation
Ceiling Mount Brackets
Support Structure
The motor requires standard AC input (unless an alternate voltage has been
specified). All connections are made to the electrical box on the side of the
unit (audience left).
In addition to the standard high-voltage 3-position switch, there are optional
switch controls available. Follow the inst allation procedure for the type of
switch control you will install.
General suggestions for wiring:
Soldering is recommended.
The use of wire nuts is acceptable.
On models not provided with armored whip, a romex connector
should be installed in the appropriate electrical KO (Knock Out).
Refer to Figure 5 for an illustration of the electrical connection box on the
side of the screen unit.
6Stewart Filmscreen Corporation
STEP 2. ELECTRICAL HOOK-UP
Caution
Professional techniques should be used when making any
electrical connection. A qualified electrician should perform
these procedures.
Be sure to follow all standard safety procedures for installing
electrical devices.
Do not disassemble or alter the configuration of the motor or
the unit's electrical connections. This may cause injury to you
or damage to the product.
The electrical connection should be made only to the type of
power source indicated on the marking label.
Figure 5: Electrical connection
box
Electrical
Connection
Box
Electrical
Knockout
Electrical
Access
Plate
Screen
Model A Electriscreen: Owner’s Manual 7
Installing the high voltage switch control (standard)
A standard 3-position wall switch is supplied. The high voltage control is
connected to the electrical source. It alternates directions of screen motion
by means of the hot lead, using the 3-position switch.
Preparing the connection
Before making the electrical connections, you need:
An available AC constant power source
A 4-conductor romex or motor connector cable
Making the connections
The diagram in Figure 6 illustrates the connections.
1. Connect the wall switch to the AC constant power source.
2. Connect the wall switch to the screen unit’ s electrical box.
Figure 6: High voltage control wiring diagram
Screen Switch
AC Power
Source
DOWN-Black
UP-Red
Line (Hot)
COMMON-White (Neutral)
GROUND-Green
Warning!
Do not connect multiple high voltage control switches to one
screen motor. For custom switching applications, cont act the
factory.
Connecting the screen trigger interface option
The optional 12V screen trigger interface enables up and down operation of
the screen in conjunction with a projector , tuner, VCR, cable box, or
switched AC outlet.
Once the AC power outlet is installed near the screen, an electrician is not
needed to connect the screen trigger interface to the power source.
Note: An optional 12VDC transformer is used if there is no 12V power
source from the projector or AV control center.
Preparing the connection
Before making the electrical connections, you need:
An available AC constant power source installed near the screen
Making the connection
The electrical diagram in Figure 7 illustrates the connection.
1. Plug the AC power cord into the AC outlet.
2. Attach the 12V trigger wire to the jack in the plate.
8Stewart Filmscreen Corporation
Figure 7: Screen trigger interface connection
To Projector
or
AC Power Source
AC Power Source
Optional 12 VDC
Transformer
With Switch
Table des matières
Autres manuels Stewart Filmscreen Écran de projection
Stewart Filmscreen
Stewart Filmscreen CM-1005 Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen Cine-W Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen AB Electriscree Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen Cabaret Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen Luxus Deluxe ScreenWall Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen Vertical ES EM Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen Visionary Electriscreen Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen Visionary Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen Balon Series Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen Visionary Medio Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen Luxus Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen Luxus Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen Cima Instructions originales
Stewart Filmscreen
Stewart Filmscreen ABT Trapdoor Electriscreen Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen VistaScope Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen Balon Series Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen Fixed Frame Screen Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen C Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen 4-Way ScreenWall ElectriMask Manuel utilisateur
Stewart Filmscreen
Stewart Filmscreen Stealth Trapdoor Electriscreen Manuel utilisateur
