Steelcraft VIRTU Manuel utilisateur
VIRTU
TRAVEL SYSTEM STROLLER
www.britax.com.au Series TK321
Suitable for use with Britax Unity Baby Capsule.
(Baby capsule and recivers both sold separately)
IMPORTANT: KEEP THIS BOOKLET IN A SAFE PLACE FOR FUTURE REFERENCE
britax.com.au
2
WARNINGS
WARNINGS:
ALWAYS APPLY THE BRAKES WHENEVER THE STROLLER IS STATIONARY.
• DO NOT LEAVE CHILDREN UNATTENDED.
• SECURE THE CHILD IN THE HARNESS AT ALL TIMES.
• DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS STROLLER.
• MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU
ADJUST THE STROLLER.
• DO NOT USE ANY ACCESSORIES OTHER THAN THOSE APPROVED FOR USE
WITH THIS STROLLER BY BRITAX.
• IT IS UNSAFE TO USE ACCESSORIES NOT APPROVED FOR USE WITH THIS
STROLLER.
• THE MAXIMUM WEIGHT OF THE CHILD USING THIS STROLLER IS NOT TO
EXCEED 20 KG. 15KG FOR MOTHER FACING BABY MODE,
12KG FOR THE BRITAX UNITY BABY CAPSULE (SOLD SEPARATELY).
FOR IMPORTANT NOTES AND WARNINGS ON ACCESSORIES - REFER TO
THEIR INDIVIDUAL SECTIONS IN THIS BOOK OR THE INSTRUCTION MANUAL
INCLUDED WITH THE INDIVIDUAL PRODUCTS. THE MAXIMUM WEIGHT VARIES
FOR EACH ACCESSORY.
This CAUTION Symbol is shown at certain steps in
this Instruction Manual to highlight the danger of
being injured by moving parts.
TO AVOID INJURY OR DEATH:
ALWAYS FOLLOW THE MANUFACTURES INSTRUCTIONS.
READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY AND USE OF THIS
STROLLER.
THE CORRECT USE AND MAINTENANCE OF THIS PRODUCT IS ESSENTIAL.
CAUTION
britax.com.au 3
• USE GREAT CARE WHEN USING THE STROLLER ON STAIRS, ESCALATORS,
TRAVELATORS OR OTHER MOVING SURFACES.
• IT IS RECOMMENDED TO REMOVE THE CHILD FROM THE STROLLER
BEFORE GOING UP OR DOWN STAIRS OR ESCALATORS.
• DO NOT LIFT THE STROLLER BY THE ARM BAR (SUPPLIED) BECAUSE IT
MAY DISENGAGE.
• DO NOT ALLOW CHILDREN TO STAND ON THE SEAT.
• DO NOT HANG BAGS UNLESS THEY ARE SUPPLIED OR GOODS FROM THE
HANDLE AS THIS COULD CAUSE THE STROLLER TO TIP OVER.
• DO NOT LEAVE THE STROLLER AND ITS ACCESSORIES NEAR AN OPEN
FIRE OR EXPOSED FLAME.
• DO NOT PLACE MORE THAN 10 KG IN THE BASKET.
IMPORTANT NOTES
britax.com.au
4
The SMART lifting technique
This technique can be used to pick up small light loads from low
levels.
Size up the Load
• Assess the load (size, shape and weight).
• Assess whether the load needs to be moved;
• Where is it going to be placed, check that there are no obstructions;
• Assess whether mechanical or human assistance is required.
Move the Load as close to the body as possible
• A load is heavier to lift or carry if it is not close to the body.
• The whole hand should be used to ensure a firm grip.
Always bend your knees
• Maintain balance.
• Keep feet apart and in a comfortable position.
• Minimise lower back bending.
• Bend knees preferable at as large an angle as possible but not at a
right angle use a semi squat in preference to a full squat.
Raise the load with your legs
• Achieve the lift smoothly and without jerkiness.
• Maintain the normal curvature of the spine to allow the force of the
load to be distributed evenly from the spine to the pelvis.
Turn your feet in the direction that you want to move the load.
• Avoid unnecessary bending, twisting and reaching.
• Change direction by turning your feet and not your back.
• To set the load down, squat down, keep your head up and
• Let your legs do the work.
Remember to ‘THINK TALL’ chest lifted, shoulders relaxed, chin
tucked in and head level.
MANUAL HANDLING TECHNIQUES
britax.com.au 5
PARTS LIST
1x Stroller Frame & Basket 1x Stroller Seat
1x Canopy 1x Arm Bar
2x Front Wheels 2x Rear Wheels
britax.com.au
6
STROLLER ASSEMBLY
IMPORTANT NOTES:
PLEASE REFER TO PAGE 6 FOR SMART LIFTING TECHNIQUES.
• RELEASE THE STORAGE LATCH WITH DUE CARE AND OPEN THE FRAME.
• WHEN OPENING THE STROLLER, BE AWARE OF THE DANGER OF BEING
INJURED BY MOVING PARTS AND LOCKING DEVICES DURING THE
PROCESS. KEEP ALL HANDS AND LIMBS CLEAR OF THESE PARTS.
• THERE IS POTENTIAL FOR FINGERS OR PARTS OF THE BODY TO INJURED
WHEN THE STROLLER IS BEING UNFOLDED, DUE CARE SHOULD BE
EXERCISED.
• KEEP CHILDREN CLEAR OF THE STROLLER WHEN UNFOLDING THE
STROLLER.
• OPEN THE STROLLER SLOWLY AND BE CAREFUL WHERE YOU PLACE
YOUR HANDS. KEEPING YOUR HANDS ON THE HANDLE IS THE BEST WAY
TO UNFOLD THE STROLLER.
OPENING THE STROLLER FRAME
AOpen the frame lock latches inside
the frame. The lower part of the
stroller will be open.
BLift the handle upwards until the
frame is fully open and locked.
CAUTION
A B
britax.com.au 7
STROLLER ASSEMBLY
ATTACHING OR REMOVING THE REAR WHEELS
AInsert wheel axle into the moulding
and push in until you hear a ‘click’.
Pull on each wheel to make sure
it is securely attached. Repeat the
process if not locked in.
BTo remove the rear wheels, press
and hold the release button in the
wheel housing and pull away.
A B
ATTACHING OR REMOVING THE FRONT WHEELS
AInsert each front swivel wheel
assembly into the wheel moulding
and push in until you hear a ‘click’.
Pull on each wheel to make sure
it is securely attached. Repeat the
process if not locked in.
BTo remove the front wheels, push
the release button on wheel
moulding.
A B
britax.com.au
8
STROLLER ASSEMBLY
ATTACHING THE STROLLER SEAT
IMPORTANT NOTE:
ALWAYS REMOVE YOUR CHILD FROM THE STROLLER SEAT BEFORE
INSTALLING, REMOVING OR CHANGING THE SEAT DIRECTION.
PLEASE NOTE: The seat is reversible so it can be attached to the frame in
the forward facing position or the rearward facing position.
AHold the stroller seat over
the frame and align the seat
connectors with frame sockets.
Push down on the seat until both
stroller seat connectors have
locked into the frame sockets.
A B
CAUTION CAUTION
BPull up on both sides of the seat to
ensure the seat is locked.
britax.com.au 9
STROLLER ASSEMBLY
ATTACHING THE CANOPY
IMPORTANT NOTE:
The sun is very strong. DO NOT LEAVE YOUR CHILD EXPOSED TO THE SUN.
The canopy or hood on this product will not give your child total protection
from the harmful rays of the sun.
A
Place the canopy on the stroller seat
and push the clips on the sides of the
canopy onto the stroller seat until they
snap into place.
B
Attach the canopy to the seat unit
with the zipper. There is peek a boo
window for viewing and ventilation.
A B
CAUTION
britax.com.au
10
STROLLER ASSEMBLY
ATTACHING THE ARM BAR
WHEN A CHILD IS IN THE STROLLER, KEEP THE ARM BAR ATTACHED AT ALL
TIMES.
AInsert the arm bar mouldings into
the sockets on each side of the
stroller frame and push down on
the arm bar until a ‘click’.
To assist with putting a child in
the stroller, you can release the
arm bar on one side. Press the
button on the side of the arm bar
moulding and pull the arm bar up
and out of the socket. Rotate the
arm bar clear of the stroller.
Reattach the arm bar after
fastening the child in the harness.
BTo remove the arm bar, press the
button on each side of the arm bar
moulding and pull arm bar up and
out of the sockets.
A B
CAUTION
Table des matières
Autres manuels Steelcraft Poussette
Steelcraft
Steelcraft H309Q Manuel utilisateur
Steelcraft
Steelcraft AX633-TS Series Manuel utilisateur
Steelcraft
Steelcraft Holiday Umbrella Layback Manuel utilisateur
Steelcraft
Steelcraft SAVVI Manuel utilisateur
Steelcraft
Steelcraft PROFILE Manuel utilisateur
Steelcraft
Steelcraft strider V5 Manuel utilisateur
Steelcraft
Steelcraft HB 5300 Series Manuel utilisateur
Steelcraft
Steelcraft AX101 series Manuel utilisateur
Steelcraft
Steelcraft Orion H2994 series Manuel utilisateur
Steelcraft
Steelcraft Holiday Manuel utilisateur
Steelcraft
Steelcraft AX108 Manuel utilisateur
Steelcraft
Steelcraft EZ ride Manuel utilisateur
Steelcraft
Steelcraft strider V5 Manuel utilisateur
Steelcraft
Steelcraft Accent H318 Series Manuel utilisateur
Steelcraft
Steelcraft Strider Plus Manuel utilisateur
Steelcraft
Steelcraft EX3 Manuel utilisateur
Steelcraft
Steelcraft PROFILE Manuel utilisateur
Steelcraft
Steelcraft strider mini Manuel utilisateur
Steelcraft
Steelcraft DUO TWIN - SERIE AX108T Manuel utilisateur
Steelcraft
Steelcraft CRUISER - SERIES H609 Manuel utilisateur
