StattQualm SQuape Manuel utilisateur
StattQualm – January 2014
PRODUCT DESCRIPTION / HOW TO DO THE WICK
Technical Data
Rebuildable atomizer / Tank atomizer in stainless steel casing
Material Tank: Stainless steel
Surface: Raw in two different rotary stages
Material Base: Stainless steel
AtomizerChamber: Aluminium, ematal coated not conductive
Windows: PAS-PMMA XT, colorless (o-ring tight,
threadless)
Diameter: 22.7mm
Height: 55mm (without Drip Tip)
Weight: 82 g
Volume: maxium 5.2ml
Airflow: via lateral opening with the 510er –
threaded connection
Center Pin: Adjustable
Accessories: Drip Tip, spare screws and o-rings, additionally an hexagon wrench to remove
the bell)
Optional: Perfectly seated ProVari-Cone
Description:
The SQuape was developed with the intention to make it a most ideal and manageable atomizer. As a reliable
everyday product it’s for the ease of expert vapers as well as for rebuildable atomizer newbies. In addition the
developers wanted to make the product most cost effective for the optimum in comfort and everyday usage.
The SQuape is made from stainless steel, rebuildable atomizer, 100% produced in Switzerland. Along with an
appealing look the atomizer is especially convincing by its high functionality. The device allows for easy doing
the wick, it is short circuit safe; this is due to the spellbound electrical impulses. (The device is coated with the
ematal coating and an aluminium surface finish*). Short circuit messages are a thing of the past since the
intelligent battery carrier. The SQuape will be sent in fully constructed usable condition, additionally these
replacement items will be included: spare screws, o-rings, one hexagon wrench as well as a specifically to the
SQuape engineered Drip Tip.
*
Ematal is an intensive process in the making of the topcoat for the aluminium item. In opposition to other specific oxidation methods
this is supreme to a higher dimensional and a very tight surface structure. The anodic process adds a permanent and virtually scratch
resistant surface to the functional parts made from aluminium. Highly stressed parts such as high pressure relief valves or materials
from medical components which are made out of aluminium undergo this process. This is utilized due to the fact that there is less
roughness by the movable parts thus less costly lubrication is required.
Our advantage: ematal coated aluminium items are non-
conductors!
StattQualm – January 2014
Important advices
The base cannot be disassembled (only the screws, the Centerpin and the o-ring).
For the dismantling of the bell a hexagon wrench is included. The dismantling of the bell eases the
process of cleaning the vapor chamber.
The PMMA-Glass (Acrylglas, aka Plexiglas) is indeed stable against menthol flavor. However, damage
due to high concentration of certain menthol-flavors, ie. Cool Mint from Inawera, cannot entirely be
excluded.
If you dismantle the glass tanks please get get the manual on www.squape.ch. The glass behind the
stainless steel tank is very stable and well protected.
We recommend to wash out the device before using it the first time.
StattQualm – January 2014
How to do the wick
The makers of the SQuape are working from personal experience and suggest following the systematic
instructions by first usage. The instructions are easy to follow and have been tested multiple times.
For tinker and do-it-yourselfer the instructions may be simple and you may look for solution by yourselves.
There is no prevention of finding improvements and suggestions.
You can do the wick with basically any on the market available tools. Of course the decision to use the correct
winding is important for the success of the atomizer. However, there are far fewer limitations or possible
mistakes as in similar atomizers. A proven option is shown more detailed:
1. Step:
Two 3 mm fiberglass cords, wound, lenght
apprx. 3 cm
0.16er Kanthal
Side Cutter
ie: Winding help
2. Step:
Overlay both cords and wire 3,5 till 4,5 turns
around the cords
3. Step:
Place the wick into the provided channel and
place the wire under the screws. Thus the
screws can be tightened by hand or using a
standard screwdriver. The lower cord should lay
tight in the channel.
At this time one can measure the resistance and
act accordingly.
The shown diagram depicts the winding of three
times with 0,16er wire for a resistance of 2.0
Ohm.
StattQualm – January 2014
Factual: Wicks are dunked in Liquid and multiple short glows through the development phase.
4. Step:
The most important and decisive moment:
Vertical channels in the base should remain
free. On the one hand, it will achieve an
optimum liquid flow, on the other hand you
might risk depressing the liquid flow.
Subsequent the bell is put over the base where
the fiberglass cords are. These need to be cut to
their correct length, since when pinched you
will cut off the flow of liquid.
Both wicks are shortened to be flush with the
outside of the base!!
5. Step:
The filling of the SQuape’s is simple and quick.
As you dismantel the tank from the base, one
needs to turn the item upside down due to the
fact that the filling hole is on the bottem of the
Base. The SQuape holds a maximum of 5.2 ml
and thus is at maximum filling volume.
Using a hollow needle bottle designed to fill is the
simplest, but a normal bottle may be used, this
makes it childsplay!
Attention! In addition do not fill the bell!
StattQualm – January 2014
Cleaning of the SQuape
The SQuape allows cleaning in warm water. Due to the fact that the shell of the tank is not polished, there are
no fingerprints visible. If you like to clean the tank inside, you simply need to remove the bell with the
provided hexagon wrench. Simply remove the tank with the wrench from the bell by placing the wrench on the
bottom of the bell and turning. Once the tank is cleaned, the bell will be fastened in the same manner.
At times Isopropanol or Ethanol will be used to clean the mechanism to remove the last/remaining odors. To
protection of the glasses it is recommended that Isopropanol is diluted 1:1 with distilled water, Ethanol should
be diluted 1:4. The cleaning with Ethanol as with Isopropanol is the owner/users responsibility– StattQualm
assumes no liability for damage.
The StattQualm-Team wishes you much success and enjoyment with the atomizer SQuape!
Table des matières
Autres manuels StattQualm cigarette électronique
Manuels cigarette électronique populaires d'autres marques
STEAMAX
STEAMAX TFV8 X-BABY Manuel utilisateur
iQOS
iQOS 3 MULTI Manuel utilisateur
Vaporesso
Vaporesso LUXE XR MAX Manuel utilisateur
ZAZO
ZAZO PRO Mini 2 Manuel utilisateur
Aquafog
Aquafog Turbo XE Manuel
Electronic Cigarettes Australia Pty Ltd
Electronic Cigarettes Australia Pty Ltd AUSSIE BLUE ENDURANCE Manuel utilisateur
