StarTech.com ST12MHDDCRP Manuel utilisateur
Manual Revision: 01/16/2013
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
ST12MHDDCRP
HDMI® Over CAT5/6 Repeater for
ST12MHDDC
*actual product may vary from photos
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Introduction ............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements .............................................................................................................................. 1
Preparing Your Site ................................................................................................................................... 4
Hardware Installation .............................................................................................................................. 5
Specications ..........................................................................................7
Technical Support ..................................................................................8
Warranty Information ............................................................................8
Instruction Manual
1
Introduction
The ST12MHDDCRP HDMI® to CAT5 Repeater works with the ST12MHDDC HDMI®
Extender Kit to add additional displays and extend the HDMI® over Cat 5/6 signal. With
2 RJ45 outputs per unit, each repeater allows you to add a display, and also daisy-chain
the signal to 2 additional ST12MHDDCRP repeaters (sold separately) at up to 330 feet
(100 meters) at each level.
Additional repeaters can be added at any time, up to a maximum of 30 broadcasting
levels to over 100 displays - allowing for a highly scalable installation that can be used
with existing network cable for a cost-eective and exible extension. Each repeater
includes mounting hardware for a clean and professional installation. Plus, because
the HDMI® signal is extended over standard Cat5/Cat6 Ethernet cable with RJ45
connectors, proprietary cables aren’t necessary which eliminates both expense and the
hassle of running specialized cable.
Ideal for High-Denition applications, the HDMI® over UTP extender supports 1080p
video resolutions, 7.1 digital audio and features built-in EDID monitor emulation,
which ensures native resolution and maximum compatibility with your display or
projector, for a convenient plug-and-play installation.
Backed by a StarTech.com 2-year warranty and free lifetime technical support.
Packaging Contents
• HDMI® Repeater
• Power Adapter
• Instruction Manual
• Foot Pad Set
System Requirements
• ST12MHDDC HDMI® Extender Kit
• HDMI® enabled display device(s) One for each Repeater (i.e. television, projector)
• Available AC electrical outlet for transmitter, receiver and optional repeaters
• HDMI® cable for each display
Instruction Manual
2
ST12MHDDCRP Repeater Unit
Transmitter Unit
Front View of Repeater
Front View of Transmitter
Back View of Repeater
Back View of Transmitter
1. HDMI® Out
2. Power Status LED
3. Link Status LED
4. EDID Copy Button
1. Power jack
2. HDMI® Out Link #1 (RJ-45 Connector)
3. HDMI® Out Link #2 (RJ-45 Connector)
4. HDMI® In Link (RJ-45 Connector)
ST12MHDDC HDMI Extender Kit (Sold Separately)
1. HDMI® IN
2. Power Status LED
3. Link Status LED
1. Power Jack
2. HDMI® Out Link (RJ-45 Connector)
Instruction Manual
3
Receiver Unit
Front View of Receiver Back View of Receiver
1. HDMI® IN
2. Power Status LED
3. Link Status LED
1. Power Jack
2. HDMI® Out Link (RJ-45 Connector)
Instruction Manual
4
Preparing Your Site
NOTE: This device will only work with the ST12MHDDC HDMI Extender kit. Please
review site preparation steps from the ST12MHDDC manual prior to installing
additional Repeaters.
1. Determine where the Repeater/Display will be installed in relation to the
ST12MHDDC HDMI Extender kit (sold separately) and place/mount the display
appropriately.
2. (Optional) If using additional repeater unit(s) (sold separately), determine where
the remote display(s) will be located in relation to this repeater/display and place/
mount the display(s) appropriately. Repeaters allow for an additional 330 ft. (100
meters) of Cat5/6 between each device. The Repeater(s) must be situated between
the ST121MHDDC extender and the receiver, as the receiver portion does not have
an RJ-45 out port to continue the chain.
NOTE: Ensure the Repeater Unit(s) are situated near an available AC electrical outlet.
Make sure all devices are turned o before beginning installation.
Instruction Manual
5
Hardware Installation
NOTE: This device will only work with the ST12MHDDC HDMI® Extender kit. Please
review the Hardware Installation steps from the ST12MHDDC manual prior to installing
additional Repeaters.
1. Install RJ-45 terminated Cat5/6 Ethernet Cable
a) Connect an RJ-45 terminated Cat5/6 Ethernet cable to the HDMI® Out Link (RJ-45
Connector) on the local Unit (Transmitter or Repeater).
NOTE: If you are using surface cabling, ensure you have enough Category 5/6
unshielded twisted pair (UTP) network cabling to connect the Transmitter Unit to
the Remote Unit’s (Repeater/Receiver) location, and that each end is terminated
with a RJ45 connector. The cabling should not go through any networking
equipment (i.e. router, switch).
OR
If you are using premises cabling, ensure that the Category 5/6 unshielded
twisted pair (UTP) network cabling between the Host Unit and the
Remote Unit has been properly terminated in a wall outlet in each location and
there is a patch cable long enough to connect the Remote Unit and the Host Unit
to their respective outlets. The cabling should not go through any networking
equipment (i.e. router, switch).
b) Connect the other end of the Cat5/6 cable run to the RJ45 connector on the
Repeater unit.
c) (optional) When adding multiple repeaters, a run of Cat 5/6 cable will be
required from and to each device.
2. Install Repeater Unit(s)
a) Position the Repeater Unit near the video display (i.e. television, projector) within
330 ft. (100 meters) from the level up device be it the initial transmitter or
another repeater.
b) Connect the video source to the HDMI® Out on the Repeater Unit using an
HDMI® cable.
c) Connect the Cat5/6 cable positioned in Step 1 to the”HDMI® In Link (RJ-45
Connector)” on the Repeater. Connect the Repeater Unit power supply. The
Power LED will light, and LINK LED will turn on after a successful connection
between both units is established. This may take several seconds.
Instruction Manual
6
NOTE: These steps can be repeated at each level when adding additional Repeaters up
to 30 levels. Each Repeater has two HDMI® out Links (RJ-45 Connectors) allowing for
the same signal to go in 2 dierent directions at each level.
3. Install Receiver Unit
d) Position the Receiver Unit near the video display (i.e. television, projector) within
330 ft. (100 meters) from the level up device be it the initial transmitter or
another repeater.
e) Connect the video source to the HDMI® out on the Receiver Unit using an
HDMI® cable.
f) Connect the provided Receiver Unit power supply. The Power LED will light,
and Link LED will turn on after a successful connection between both units is
established. This may take several seconds.
NOTE: The ST12MHDDC receiver (sold separately) should only be used as the last
device in the chain as it does not have an HDMI® out port (RJ-45 Connector).
4. Your source video image will now appear on the Repeater unit(s) attached
video display.
Instruction Manual
7
Specications
Input Connectors 1x RJ-45 Female
Output Connectors 1x RJ-45 Female
1x HDMI (19 pin) Female
Max Distance 100 m / 330 ft
Maximum Digital Resolutions 1920x1200 @60Hz
Supported Resolutions
1920 x 1200
1920 x 1080
1600 x 1200
Wide Screen Supported Yes
Audio Specications 7.1 Surround Sound
Power Adapter
Input Voltage 100~240V
Input Current 0.4 A A
Output Voltage 5 AC V
Output Current 2 A A
Center Tip
Polarity Positive
Plug Type M
Table des matières
Autres manuels StarTech.com Changer
StarTech.com
StarTech.com ST4202USB Manuel utilisateur
StarTech.com
StarTech.com SV231DDVDUA Manuel utilisateur
StarTech.com
StarTech.com 5G16AINDS-USB-A-HUB Manuel utilisateur
StarTech.com
StarTech.com SV431DPDDUA2 Manuel utilisateur
StarTech.com
StarTech.com SV831DUSBUK Manuel utilisateur
StarTech.com
StarTech.com SV231DD2DUA Manuel utilisateur
StarTech.com
StarTech.com SV215MICDVIA Manuel utilisateur
StarTech.com
StarTech.com ST4205READ Manuel utilisateur
StarTech.com
StarTech.com VS221VGA2HD Manuel utilisateur
StarTech.com
StarTech.com IES81000POE Manuel utilisateur
StarTech.com
StarTech.com 35BAYFWUSB Manuel du système
StarTech.com
StarTech.com ICUSB2322X Manuel utilisateur
StarTech.com
StarTech.com SV231TDVIUA Manuel utilisateur
StarTech.com
StarTech.com SV841HDI Manuel utilisateur
StarTech.com
StarTech.com SV231DVGAU2A Manuel utilisateur
StarTech.com
StarTech.com IESC1G80UP Manuel utilisateur
StarTech.com
StarTech.com 5G4AINDRM-USB-A-HUB Manuel utilisateur
StarTech.com
StarTech.com StarView SV221DD Manuel
StarTech.com
StarTech.com 8STSV431DPDDUA2 Manuel utilisateur
StarTech.com
StarTech.com Presentation Jockey Manuel
