StarTech.com PCICOMBO Manuel utilisateur

Installation Manual

PCICOMBO

Network Card

10 Mbps PCI Ethernet Card with Dual Interface

General Description

StarTech.com’s PCICOMBO PCI Network card comes with full support for duplex

modes and autoconfiguration through a workstation’s PCI BIOS, this PCI Card features

optional AUI connectors. Bus Mastered to greatly reduce system CPU load and sporting

a boot ROM socket for optional RPL boot ROM, this product is designed to provide

customers with an optional, dual interface for the Networking needs.

Features

• 32-bit PCI 2.0 Bus interface

• Plug and Play compatible with Windows 95, 98, ME, and Windows 2000

• Fully autoconfiguring through the computer's PCI BIOS

• Supports full duplex mode

• Low power consumption with sleep mode for energy saving PC's

• Optional AUI connector

• Bus Mastered to greatly reduce system CPU load

• Coax interface allows cable distances of up to 300m

• Boot ROM socket for optional RPL boot ROM

• Complies fully to IEEE 802.3 CSMA/CD Ethernet 10BaseT and 10Base2 Standards

• Two LED's indicate LINK and activity

• Drivers for all operating systems

Specifications

Standards IEEE 802.3 10BaseT, 10Base2, 10Base5

Data Transmission Rate

LEDs

Bus Type

IRQ

Boot ROM

Temperature

Dimensions

Certification

10Mbps or 20Mbps

UTP link status, Activity

PCI 2.0

Assigned by system

0 to 50 degrees C

140 x 63 mm

FCC part 15 class A, CE Mark

I/O Address

Getting Started

This section is designed to help you prepare the PCICOMBO card for installation. Please

read through this section carefully before attempting to install the card.

Unpacking the PCICOMBO card

This package should contain:

1 x PCICOMBO Network card

1 x BNCT connector

1 x driver disk

Installation

Network cards, like all computer equipment are subject to static electricity. Be sure that

you are properly grounded. StarTech.com recommends that you wear an anti-static strap

and that your system is unplugged before doing any work on the computer.

Card Installation

1. Turn off the computer and remove its cover.

2. Insert the card into a free PCI slot.

3. Connect to the network using AUI, thin or twisted-pair cable depending on the

connector you are using.

Card Configuration/ Diagnostic

Basically, the card is completely self-configurable, requiring no intervention from the

user. There are only 3 items that can be configured: Medium type, Full/Half duplex, and

Boot ROM enables. You can also run diagnostic of the card from the setup.exe program

provided with the PCICOMBO card.

Insert the disk provided, in DOS prompt, execute setup.exe command and you will see

the following:

• View Configuration

• Manual Setup Configuration

• Diagnostic

• Exit

Please follow the easy menu-driven program to configure the card.

Driver Installation

For detailed information, please refer to the document in the disk provided.

Examples:

1. For NetWare client, please execute the following:

lsl

pciodi

ipxodi

netx or vlm

2. For NetWare server, execute the following:

load pcisrv

bind ipx pxisrv

load monitor

Boot Rom Installation (Optional)

The PCICOMNO card provides a socket for a remote boot ROM. With a boot ROM, a

host computer can load the operating systems over the network.

1. Plug in the boot ROM to the appropriate position, make sure the direction is correct.

2. Enable the boot ROM function. Please see the Setup program for details.

AUI Bracket Installation (Optional)

You can buy another bracket containing an AUI connector from your dealer.

1. Hook up the cable to the connector pins market “AUI”. Make sure the red line on the

cable is positioned in the “pin 1” location.

2. Secure the bracket to the PC.

Troubleshooting

The most common factors that cause an adapter to fail are configuration conflicts and

cabling problems. PCI cards shouldn’t have any conflct problems due to Plug and Play

specifications. One should check the cable and its terminator. Also, use the adapter LED

indicators and diagnostic program. For information on the Diagnostic Program, please

see the Setup program. If the problem presists, call your dealer for help.

LED Indicators

The LEDs help you monitor the network status. Their functions depend on the type of

cable used.

*Link monitors the data link status on the UTP cable. It turns ON when there is data

linked, and OFF when there is a bad connection.

*Activity blinks when there is data transmission/reception.

Table des matières

Autres manuels StarTech.com Carte PCI

StarTech.com

StarTech.com PCIESATA2I Manuel utilisateur

StarTech.com

StarTech.com PEXSATA22I Manuel utilisateur

StarTech.com

StarTech.com PEX8S1052 Manuel utilisateur

StarTech.com

StarTech.com PEX1S553 Manuel utilisateur

StarTech.com

StarTech.com PCI225USB Manuel utilisateur

StarTech.com

StarTech.com PEXUSB3S42V Manuel utilisateur

StarTech.com

StarTech.com PCIUSB3S2 Manuel utilisateur

StarTech.com

StarTech.com PEXUSB3S4 Manuel du système

StarTech.com

StarTech.com PEX1S1P950 Manuel utilisateur

StarTech.com

StarTech.com 8STPEX1394B3LP Manuel utilisateur

StarTech.com

StarTech.com ST1000SPEX4 Manuel utilisateur

StarTech.com

StarTech.com PCI3UV22F Manuel utilisateur

StarTech.com

StarTech.com PCI1394MP Manuel utilisateur

StarTech.com

StarTech.com PEX1S1PMINI Manuel utilisateur

StarTech.com

StarTech.com PEXUSB314A2V Manuel utilisateur

StarTech.com

StarTech.com DUAL-M2-PCIE-CARD-B Manuel utilisateur

StarTech.com

StarTech.com PEX300WN2X3 Manuel utilisateur

StarTech.com

StarTech.com PCI312PUSB/LP Manuel utilisateur

StarTech.com

StarTech.com USB2HDCAPS Manuel utilisateur

StarTech.com

StarTech.com PCI4S550N Manuel utilisateur

StarTech.com

StarTech.com PCISAT2F3U4 Manuel utilisateur

StarTech.com

StarTech.com PCI2S1P Manuel utilisateur

StarTech.com

StarTech.com PCI220USB Manuel utilisateur

StarTech.com

StarTech.com PEX2S553B Manuel du système

Manuels Carte PCI populaires d'autres marques

ERMA

ERMA SSI 1417 Manuel utilisateur

SIIG

SIIG CyberSerial Dual PCI Instructions de montage

Moxa Technologies

Moxa Technologies CP-102E Manuel utilisateur

I-Bus

I-Bus IBC2602 Manuel utilisateur

Exsys

Exsys EX-60102 Manuel utilisateur

Chelsio Communications

Chelsio Communications T5 Series Manuel utilisateur

Conrad Electronic

Conrad Electronic 97 46 71 Manuel utilisateur

Micro Innovations

Micro Innovations USB650A Manuel utilisateur

KTI Networks

KTI Networks KF-310 Manuel utilisateur

Asus

Asus SpaceLink WL230 Manuel utilisateur

SIIG

SIIG SC2475 Manuel utilisateur

TRENDnet

TRENDnet TEW-703PI Manuel utilisateur

Belkin

Belkin F5D7000F Manuel utilisateur

Pericom

Pericom PI7C7100 Manuel utilisateur

ADLINK Technology

ADLINK Technology cPCI-3548 Manuel utilisateur

Digium

Digium TE200 Series Manuel utilisateur

Allo.com

Allo.com 2nd Gen E1/T1/J1 Manuel utilisateur

Western Digital

Western Digital FireWire PCI Adapter Manuel utilisateur