Starburst Technologies SB-HDQP-2130 Manuel utilisateur

8VSB / ATSC to QAM Processor

SB-HDQP-2130

INSTRUCTION MANUAL

The content and design of this document is the intellectual property of PDI Communications, Inc. and is protected

Under copyright law. Any duplication of this material without written consent of an authorized officer of this company

Will be litigated to the fullest extent of the law.

Starburst

Technologies Customer Support •1-800-242-1606 ext. 274 1

Rev 2a

INTRODUCTION

Thank youfor buying the SDQM-2130 MPEG-2 SD Encoder

Modulator Combo. Please read this manual carefully before

Installing. Tomaintain the best performance of the SDQM,

keep this manual at hand for future reference.

General

Description

Main

Features

◆

2U design

◆

QuickBoot-up

◆Coversfrequencyrange from54 to860MHz

◆

Localcontrolvia friendlyfrontbuttonControlPanel

◆

Remotecontrolvia supplied utility

SAFETY

INSTRUCTION

All the safety and operating instructions should be read

before the product is operated. For safety purposes, all

instructions must be adhered

to.

Cleaning

Unplug the unit from the rack before cleaning. Do not

use

liquid or aerosol cleaners. Use adamp cloth.

Attachments

Do not use attachments that are not recommended by

the manufacturer

as they can cause hazards.

ater

and

moisture

Do not use this product near water.

Mounting

Ensure the unit is rack mounted securely on the wall or in the

19’’ cabinet as not to cause harm to anyone or to damage

the product by being dislodged.

Power

cord

protection

Power-supply cords should be routed so they are not

pinched or placed where they could cause atrip hazard.

Ventilation

Slots and openings in the housing are provided for ventilation

to prevent overheating and ensure reliable operation.These

openings should never be blocked or covered by

placing the unit on acarpet, flooring, furniture or fabric

surface. The unit should not be placed in abuilt-in

structure such as acupboard or rack unless proper

ventilation is

provided.

Power

source

This unit should only be operated from the type of power

source indicated in the technical specifications (page 3of this

manual).

Lightning

For added protection; unplug the unit from the wall

when left unattended or unused for long periods of time and

disconnect the cable system. This will protect the product

from lightning strikes or power surges.

Object

and

liquid

entry

Never push objects of any kind into this product through

openings as they may touch dangerous voltage points or

short-out a part that could result in afire or electric shock.

Never spill liquid of any kind on the unit.

Servicing

Do not attempt to service this product yourself as opening or

removing covers may expose you to dangerous voltage or

other hazards. Refer all servicing to qualified service person-

nel.

Damage

requiring

service

Unplug this unit from the wall or the cabinet and return it to

the qualified service personnel for sevicing

if any of the

following occurs:

-The power supply cord or plug is damaged.

-Liquid has been spilled, or objects have fallen into the unit.

-The unit has been exposed to rain or water.

-If the unit has been dropped or damaged in anyway.

Heat

The unit should be positioned away from any heat source such as

radiators, fireplaces, cooking stoves, or other products (including

amplifiers) that produce heat.

Starburst

Technologies Customer Support •1-800-242-1606 ext. 274 2

OPERATION

SPECIFICATIONS

Input

hannel

Combinations: 2×ATSC / 2×QAM / 1×ATSC + 1×QAM

Input

QAM

Channel ran e: 2-134

Frequency ran e: 54-860MHz

QAM mode: 64QAM / 256QAM

Data Rate: 26.9Mbps (64QAM), 38.8Mbps

Input Level:

(

12 to +10dBmv)

Output

RF carriers:

Channel ran e:

2-134

Frequency ran e:

64QAM / 256QAM

Data rate:

26.9Mbps (64QAM), 38.8Mbps

Input

8VSB / ATSC/ OFF AIR

Tunin ran e: UHF: 14-69, VHF: 2-13

Input Level: (-30 to +10dBmv)

Frequency ran e: 54-806MHz

Data

rate:

19.392Mbps

CONTROL

Local operation:

Front panel push button

Remote operation:

Web browser

STREAM

PSIP: MGT/CVCT/STT re enerator

GENERAL

Dimensions:

68×50×250 mm

Wei ht

0.8 k

Power source:

DC 12V/ DC 5V

PWR. consumption: 12W

Manual Operation-Via front panel Push Buttons and LED Display

eb Interface/ Remote Operation – Via LAN Port

Manual Operation

To enter the Menu in manual mode, use this sequence of key strokes:

Key strokes = Press UP arrow, DO N arrow, and OK. Do this two

times! OUP should appear.

To navi ate throu h the menu manually, refer to System LED Function

Outline On p s. #4,5, & 6, alon with the Navi ational Flowchart on p . #7

NOTE: In manual operation, you must select esc to save and exit

Starburst

Technolo ies Customer Support • 1-800-242-1606 ext. 274 3

MANUAL OPERATION / SYSTEM LED FUNCTION

OUP

Enter the menu manually.

OUP

should appear.

(Continue to next step)

FCY

Pres

s OK button to enter (FCY

)

mode.

Press OK button to enter or verify channel number on the

display, Press OK button a ain to access blinkin Channel L.E.D.'s, Use the UP or DOWN buttons to

chan e or set the Output Channel Number while the L.E.D.'s are blinkin , Press OK to stop the

blinkin L.E.D.'s and confirm output channel number selection. Subsequently, OUL will be displayed

in the Output display. Continue to next step.

OUL

Once in the

mode (OUL) or Output level mode,

Press OK button to see or check the displayed outpu

level between (+15 to +30 dBmV). The factory default is 30. Press OK to access display's blinkin

L.E.D.'s. Use the UP or Down buttons to chan e or set the Level on the blinkin display. Press OK to

stop the blinkin L.E.D.'s and confirm the Output level selection. Subsequently, (CON) Constellation

will be displayed in the Output L.E.D.'s display. Continue to the next step.

CON

Once in the

(CON) mode or constellation,

Press OK button

to see or check the displayed

Constellation (256 or 64). Press OK to access blinkin L.E.D.'s. Use the UP or Down buttons to chan e

or set the Constellation on the blinkin display. Press OK to stop the blinkin L.E.D.'s and confirm the

Constellation. Continue to the next step.

Use the UP or Down

buttons to chan e or set the

Yes

will save the previous manual settin s

and no will cancel the previous manual settin s you have chosen. Finally, you will be scrolled back to

the OUP display settin . Press Up arrow then press OK to { esc and save settings }

Starburst

Technologies Customer Support •1-800-242-1606 ext. 274 4



OUP

–

Output

FCY – Frequency (Channel Number)

OUL- Output Level

CON – Constellation

HCP - HCP

esc -

Locks and saves settings

Output Settings Via Push B

utton

IP Setup Via Push Button

Input Channel S

push button

1PA

Enter m

enu

manually

OUP

appears.

Press up arrow twice for 1PA. Then OK button to enter HCP.

YES HCP

HCP

DHCP mode

, Press OK to see status of

yes

, Press Ok

a ain to put into blinkin L.E.

mode. Use the UP or Down buttons to chan e or set to yes or no. yes means it is in DHCP mode, no

means STATIC mode. If you selected no, you must assi n a different IP address Please o to the

NO-HCP section of this chart to setup the I.P. Address in Static mode. If you selected YES for DHCP, it

will automatically assi n an I.P. address with respect to your network router. If your selection is yes,

you can retrieve the

assi ned

address by

Press

OK to continue to n

ext section IP1.

IP1

This is

the first part of the DHCP IP address or IP1, Press OK to read the first number of the IP1

network address. Press OK to continue to the second part of the IP address or IP2.

IP2

This is the second part of the DHCP IP

address or IP2, Press OK to read the second number of the IP2

network address. Press OK to continue to the third part of the IP address or IP3.

IP3

This is the third part of the IP address or IP3, Press OK to read the third number of the IP3 network

address. Press OK to continue to the fourth part of the IP address or IP4.

IP4

You are now in the fourth part of the IP address or IP4, Press OK to read the fourth number of the

IP4 network address. Press OK finish readin the four parts of the IP network address detected by

the modulator or processor. Finally, you will be back to OUP mode.

NO HCP

section

After NO is Selected and saved by pre

ssin the OK button, the

modul

ator

will be factory default

ed to

the static IP address of 192.168.1.168. If you have more than one modulator you will be required to

chan e them into the correct ran e from (192.168.1.1) to 192.168.1.254) with the net mask of

(255.255.255.0) Make sure if you are usin a switch or router, that you have not assi ned any

duplicate addresses to avoid any conflicts. Press OK to next section IP1.

IP1

This is

the first part of the STATIC IP address or IP1, Pressin OK one time to read the first number of

the IP1 network address then OK a second time to make chan es, Use the UP or Down buttons to

make chan es. Finally press OK to proceed to next section IP2. Note: Blinkin allows you to make

chan es.

IP2

This is

the second part of the STATIC IP address or IP2, Pressin OK one time to read the second

number of the IP2 network address then OK a second time to make chan es, Use the UP or Down

buttons to make chan es. Finally press OK to proceed to next section IP3. Note: Blinkin allows you

to make chan es.

IP3

This is

the third part of the STATIC IP address or IP3, Pressin OK one time to read the third number

of the IP3 network address then OK a second time to make chan es, or Use the UP or Down buttons

to make chan es. Finally OK to proceed to next section IP4. Note: Blinkin allows you to make

chan es.

IP4

This is

the fourth part of the STATIC IP address or IP4, Pressin OK one time to read the first number

of the IP4 network address then OK a second time to make chan es, Use the UP or Down buttons to

chan e or set to y or n. Note: Blinkin display allows you to make chan es.

y or n

This is the final section of your new IP address you have entered manually, Use the UP or Down

buttons to chan e or set to y or n. y means to save and n means to cancel any chan es. Finally, press

OK to confirm the save or cancel the chan es for the IP address. Press Up arrow then press OK to

{ esc and save settings }

Starburst

Technologies Customer Support •1-800-242-1606 ext. 274 5

HCP

DHCP

NO HCP = STATIC

Setup Via Push Button

OUP

Enter the menu

manually

OUP

should appear.

Next, press the DOWN arrow one time to enter

CH1

mode, or press DOWN arrow two times to enter CH2 mode. “Ch1 and CH2 are Inputs.”

CH1

CH2

The d

isplay shows CH1 or CH2 depe

ndin upon which input port you

have chosen to setup. Press OK

button to continue to the typ or type section of the input si nal to be demodulated.

typ

The d

isplay shows

typ

for the type of input modulation. Pressin Ok one time to read if the input

si nal is in AtS for ATSC or 83b for J83b, then press OK a second time to make chan es, Use the UP

or Down buttons to set 83b or AtS Note: Blinkin display allows you to make chan es from ATSC to

J83b. Press OK to continue to next part FCY or Frequency. Please note that all modulators are

Factory defaulted to ATSC.

FCY

The d

isplay sho

ws FCY for the

INPUT

Channel Number

. Pressin Ok one time to read the Channel

number, Press OK a second time to make chan es to the Channel number, Use the UP or Down

buttons to chan e the channel number. Finally, Press Ok. Use the UP or Down buttons to chan e or

set y or n. y means to Save and n means to cancel chan es. Finally, press OK button to confirm the

chan es. Note: Factory defaults for ATSC Frequency is CH 23 for CH1, and the J83b default frequency

is CH 74 for CH1. FCY will jump to OUP. (CON) is not a required set up for ATSC. Only a J83b input

will continue to CON (constellation)

CON

The display shows

CON

meanin the constellation. Pressin Ok one time to read if the input

constellation is 256 or 64, for J83b Input. Press OK a second time to make chan es, Use the UP or

Down buttons to chan e from 256 to 64. Finally, press OK button to confirm the chan es, If any. y

means to Save and n means to cancel chan es. Pressin OK will scroll you back to OUP. Note:

Blinkin display allows you to make chan es from ATSC to J83b.

OUP

We have scrolled back to the be innin of manual operations mode.

Press Up arrow t

hen press OK

to { esc and save settings }

Starburst

Technologies Customer Support •1-800-242-1606 ext. 274 6



CH1

–

Input Channel for Port #1

CH2 – Input Channel For port #2

typ - Type of input (i.e. ATSC OFF AIR or QAM J83b)

83b= J83b (Qam) input –Requires constellation setup

AtS= ATSC (Off Air) input- oes not require constellation setup

FCY – Frequency (Channel Number)

CON – Constellation

esc -

Locks and saves settings

Input Channel Set

Up Via push button

Starburst

Technologies Customer Support •1-800-242-1606 ext. 274 7

NOTE:

The Factory Default Setting is DHCP

To chan e this settin to STATIC,

use front panel push buttons. (Refer to pg. #5)

STEP

1- Decide weather your connection will be

STATIC or DHCP and make the connection

acordin to dia ram (

{ NOTE: A switch is required in order to use DHCP }

hhhhhhhhhhhhhh

< Windows 7>

STEP 2- On your PC, o to Control panel> Network and

Internet> Network and Sharing Center

STEP 3

- Click on “Local area network” and select Properties

STEP 4- Select and click on 4 TCP/IPv4 then click on Properties

STEP 5- Select mode: DHCP or STATIC. Refer to diagram (1.c)

for STATIC MODE: Enter Subnet mask 255 . 255 . 255 . 0

for STATIC MODE enter default IP adress 192.168.1.

_ _ _

Enter any number from 1-254 o not use 0,3,or 168. This will

cause conflict.

This number must be different than the assigned modulator

number In order to communicate.

NOTE:

If you are usin DHCP, the switch will automaticly

asi n these numbers.

Important! Remember these IP address Numbers. You

will need to enter them in the web browser’s address bar

in order to lo in.

STEP 6- Click on OK then close.

hhhhhhhhhhhhhhhhhhhhh

hhh

Starburst

Technologies Customer Support •1-800-242-1606 ext. 274 8

Web Interface/ Remote Operation

1a.

1c.

hhhhhhhh

Ethernet

Connection

The web browser allows the user to fullyconfigure the SB-HDQP unit

via an Ethernet connection and a web browser.

A. Connect the PC to the LAN port of the SB-HDQP-2130unit.

B. The configuration process must be made acording to

instructions on page 8 of this manual. You will be able toaccess the

unit from any PC.

Launch the web browser. Enter the IP address in the address bar

and then hit Enter. “System Login” will appear. Enter the default

password to Login.

System Login

Enter the default password ‘1234’ to Login.

Note: Password can be changed after logged in under “System Parameters” tab.

RF Parameters

User can edit the parameters such as Country, Frequency, Output Level etc.

LAUNCH WEB BROWSER

Starburst

Technologies Customer Support •1-800-242-1606 ext. 274 9

Stream Parameters

User can edit the Swap VCN (Virtual Channel Name) in ‘Stream Parameters’.

Note:

Some TV models might required a complete channel re-scan in order to see the change.

System Parameters

User can reset the system or retrieve inventory.

The “Set Password” configuration enables user to change the current password.

Starburst

Technologies Customer Support •1-800-242-1606 ext. 274 10

Autres manuels pour SB-HDQP-2130

Table des matières

Autres manuels Starburst Technologies Matériel informatique

Starburst Technologies

Starburst Technologies SB-HDQP-2130 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur