Star LC-4522 Manuel utilisateur
USER’S MANUAL
LC-4522
DOT MATRIX PRINTERS
Contents
Chapter 1: Printer Setup …1
Choosing a place for the printer … 1
Upacking the printer … 2
General guide … 3
Open the front cover … 4
Removing the protective materials … 4
Installing the platen knob … 6
Installing the ribbon cassette … 6
Removing the ribbon cassette … 8
Installing the paper guide … 9
Standing up the paper guide … 10
Connecting to a power outlet and turning power on and off … 11
Loading fanfold paper … 12
Printing on fanfold paper … 16
Parking fanfold paper … 17
Unpaking fanfold paper … 17
Using the tear-off function … 18
Connecting to your computer … 18
Chapter 2: Control Panel Operations
Switching between on-line and off-line … 20
Selecting a Print Quality … 21
Entering the Print Quality Lock Mode … 21
Entering the Multi-part Mode … 22
Line feed … 23
Setting the top of form position … 24
Tear-off Function (fanfold paper) … 24
Selecting the Quiet Print Mode … 24
Changing the auto load position … 25
Save a macro … 26
Clearing the printer’s buffer … 26
Initializing the printer … 27
Chapter 3: Using the EDS Mode
About EDS Mode settings … 28
Entering the EDS Mode … 28
Selecting a bank … 29
Changing a switch setting … 29
Printing the current switch settings … 30
Exiting the EDS Mode … 30
EDS Mode Settings … 31
Chapter 4: Using the Printer with MS-DOS
Setting up for printing with MS-DOS … 40
Chapter 5: Paper Handling
Selecting paper types … 41
Adjusting for paper thickness … 43
Paper Handling … 44
Automatic fanfold feeding … 44
Manual sheet feeding … 44
Clearing paper jams … 45
1
Chapter 1: Printer Setup
This chapter contains important information on setting up your printer. Be sure
to read this chapter carefully before using the printer for the first time. In this
chapter you will learn about:
o Choosing a place for the printer
o Unpacking and setting up the printer
o Installing the platen knob
o Installing the ribbon cassette
o Loading paper
o Connecting to your computer
Choosing a place for the printer
Before actually unpacking the printer, you should take a few minutes to think
about where you plan to use it. Remember the following points when doing this.
3 Choose a firm, level surface where the printer will not be exposed to
vibration.
3 The power outlet you planto connect to for power should be nearby and
unobstructed.
3 Make sure that the printer is close enough to your computer for you to
connect the two with your printer cable.
3 Allow six inches (15 centimeters) of free space on either side of the printer.
If you are going to use fanfold paper, make sure that there is adequate space
for paper behind the printer.
3 Make sure that the printer is not exposed to direct sunlight.
3 Make sure that the printer is well away from heaters.
3 Make sure that the surrounding area is clean, dry, and free of dust.
3 Make sure that the printer is connected to a reliable power outlet. It should
not be on the same electric circuit as copiers, refrigerators, or other
appliances that cause power spikes.
3 Use a power outlet that matches the power rating noted on the label affixed
to the bottom of your printer.
3 Make sure that the room where you are using the printer is not too humid.
2 Printer Setup
Unpacking the printer
Check to make sure that the carton contains each of the items shown in the
following illustration.
If anything is missing, contact the store where you bought the printer and ask
them to supply the missing part. Note that it is a good idea to keep the original
box and all the packing materials just in case you need to pack the printer up
again and send it somewhere at a later date.
Important!
There are several versions of this printer designed for different voltages. It is
not possible to change the voltage of a printer. If the voltage shown on the label
on the bottom of your printer does not match the voltage for your area, contact
your dealer immediately.
General guide 3
General guide
The following illustrations show the major components of your printer.
4 Printer Setup
Opening the front cover
o Lift up on the front cover and swing it open until it stops.
o To close the front cover, simply lower it back into place.
Caution!
The tear assist edge is rather sharp. Take care to avoid injuring your hands.
Note:
You can completely remove the front cover from the printer or you can stand it
up. You should normally leave the front cover closed, because it protects
against objects getting into the printer, and it cuts down on printer noise.
Removing the protective materials
Two small pieces of packing material are inserted into the printer to protect
components during shipping. Be sure to remove them before using the printer.
o Open the rear cover by pushing it back so that the cover swings back and
down.
Removing the protective materials 5
o Open the front cover.
o Remove apieces of packingmaterial from inside the printer as shown in
the illustration.
A piece of cardboard is inserted into the printer to protect components during
shipping. Be sure to remove it before using the printer.
o Open the rear cover.
o Remove the cardboard from the inside of the rear cover as shown in the
illustration.
6 Printer Setup
Installing the platen knob
The platen knob is packed into a recess in the packaging material.
o Install the knob on the shaft located inside the large hole on the left side of
the printer. Make sure that the two splines of the platen shaft inside the
printer fit into the slots inside the knob’s spindle. Press the knob carefully
but firmly into place as far as it will go.
Installing the ribbon cassette
o Make sure the printer is unplugged from its power outlet.
Caution!
Never move the print head while the printer is turned on. Doing so can damage
the printer. If you have just finished printing, let the print head cool for a few
minutes before you touch it.
o Remove the front cover of the printer.
o Remove the ribbon cassette from its package.
Installing the ribbon cassette 7
o Rotate the knob on the ribbon cassette clockwise to take up any slack in the
ribbon.
o Carefully place the cassette onto the mechanism making sure that the
spindle fits into the socket on the bottom of the cassette. Also
make sure that the side tabs fit into the grooves on the sides of the flame.
Table des matières
Autres manuels Star Imprimante
Star
Star SP298 SERIES Manuel utilisateur
Star
Star AR-1000 Manuel utilisateur
Star
Star SM-L304 Series Manuel utilisateur
Star
Star SP312F Manuel utilisateur
Star
Star TSP800II SERIES Manuel utilisateur
Star
Star Multi-Font ZA-200 Manuel utilisateur
Star
Star SP712 Series Manuel utilisateur
Star
Star TSP200 Series Manuel utilisateur
Star
Star SP200F SERIES Manuel utilisateur
Star
Star TSP650 SERIES Manuel utilisateur
Star
Star SM-L200 SERIES Guide de démarrage rapide
Star
Star HSP7000 Manuel utilisateur
Star
Star SM-T300 Manuel utilisateur
Star
Star SM-S401 Manuel utilisateur
Star
Star Dot Impact Printer Manuel utilisateur
Star
Star TSP650II series Manuel utilisateur
Star
Star TSP100LAN Manuel utilisateur
Star
Star TSP650 SERIES Instructions de montage
Star
Star Tsp 100 Instructions d'utilisation
Star
Star SM-L200 SERIES Manuel utilisateur
