Star Micronics TUP400 Series Manuel utilisateur

THERMAL PRINTER

TUP400 Series

TECHNICAL MANUAL

[SECOND EDITION]

NOTICE

STAR’s express permission is forbidden.

•The contents of this manual are subject to change without notice.

•Alleffortshavebeenmadetoensuretheaccuracyofthecontentsofthismanualatthetimeofgoing

to press. However, should any errors be detected, STAR would greatly appreciate being informed

of them.

•The above notwithstanding, STAR can assume no responsibility for any errors in this manual.

• First edition : Aug.1997

• Second edition : Jun. 1998 Add interface board Ver. 2

Model Name

TUP 4 5 2 V2 D — 24 NL

No Transparent Laser

Voltage

24 : 24 VDC

Interface

D: RS232C

C: Parallel

K: RS422A

Board type

None:Ver.1

V2:Ver.2

Mechanism type

2: 40 columns

Printer type

5: Guilotine Type Full Cutter

8: Guillotine Type Full Cutter + Presenter

TUP400-series thermal printer

INTRODUCTION

This manual was created as a reference for maintenance of the Thermal Printer TUP400 Series for

personnelwhoare responsibleforperiodic inspectionsortroubleshooting ofthatequipment. This manual

was written for maintenance personnel, and was not intended to be used by the general operator.

This manual is organized into the following chapters.

Chapter 1 Specifications and Operation

Chapter 2 Theory of Operation

Chapter 3 Parts Replacement and Related Adjustments

Chapter 4 Maintenance and Lubrication

Chapter 5 Parts Lists

This page was intentionally left blank.

CHAPTER 1

SPECIFICATIONS AND OPERATION

1. General Specifications ....................................................................................... 6

2. External Appearance .......................................................................................... 7

3. DIP-Switch Settings ............................................................................................8

4. Print-Density Adjustment ................................................................................. 11

5. Sensor Adjustment ........................................................................................... 12

6. HEX Dump Mode/Test Print..............................................................................13

7. Changing the Interface Board.......................................................................... 14

– 6 –

1. General Specifications

Printing method Line thermal direct

Resolution 8 dots/mm (H) ×8 dots/mm (V)

Printable width 50 mm in Line Mode; 80 mm in Page Mode

Printing speeds 2 Inches/sec and 1 Inch/sec

Printable characters Page mode: ANK, International, Slash zero

Line mode: ANK, International, Special, Block graphics, IBM special,

IBM block graphics, Chinese characters, Slash zero

NOTE: ANK is comprised of ASCII characters and Japanese katakana characters.

Character matrixes Page mode

Small 8×16

Standard 16×24

Wide 24×32

OCR-B 16×24

Chinese chara. 24×24

Line mode

IBM block graphic 12×24 or 12×32

Chinese chara. 24×24 (12×24)

All others 12×24

Bar Codes JAN, EAN, UPC, Code39, ITF, Code93, Code128, NW-7

Paper

Recommended brands TF50KS-E, TF62KS-E (Nippon Paper Industries)

KP50-HEAEX (New Oji Paper Co., Ltd.)

Width 82.5 mm(3.25 inches)

Thickness General thermal paper 60 to 85 µm

Roll diameters External 203 mm max. (8 Inch), Internal 32 mm (1.26 Inch)

Interface RS232C, RS422A, or Parallel

MCBF 5,000,000 Lines

Head longevity 100 Km or 1.0 x 108pulses(excludes damaged caused by dirt or foreign objects.)

(Missing dots is Max. 5%. However, there will be no missing dots up to 50Km.

This is the point where the thermal body resistor value varies more than 15% of the

initial value when continuously printing up to 12.5% of the printing rate.)

Cutter longevity 300,000 cuts (One piece max. paper thickness: 85 µm.)

Power supply DC 24 V ±7%

Power consumption Max. 120 W

Operating environment Temperature 5°C to 40°C

Humidity 25% to 80% (No condensation)

Storage environment Temperature -20°C to 60°C

Humidity 10% to 90% (No condensation)

Fig. 1-1 External Dimensions

164mm

299mm

254mm

356mm

Approximately 3.3kg

Approximately 3.1kg

254mm

TUP452 TUP482

-1

– 7 –

Fig. 1-2-b Internal Configuration (TUP482)

Arm

Printer head

Presenter

Fig. 1-2-a Internal Configuration (TUP452)

2. External Appearance

Printer head

Arm

Cutter

– 8 –

3. DIP-Switch Settings

DIP switches are located on the interface board and they differ according to the type of interface.

(1) Setting the DIP Switches

1. Turn the power supply OFF.

2. Remove the screw holding the ROM cover in place. (The screw is located at the base of the paper-roll holder.)

3. Remove the ROM cover to expose the main and interface PCBs

4. Set the DIP-switches on the interface board.

Fig. 1-3 DIP-Switch Settings

DIP Switches

VP4 (Black Mark Sensor)

EPROM

Main Logic Board

VP3 (Paper End Sensor)

Interface Board (RS-232C)

Fig. 1-4 Main Interface Board

– 9 –

2. DIP-switch values

(1) RS-232C interface

This board has a single 8-bit DIP switch.

Switch Setting ON OFF

1-1 Baud

1-2

1-3 Handshake DTR XON/XOFF

1-4 Data 8 bits 7 bits

1-5 Parity No parity Enabled

1-6 Parity Odd Even

1-7 DC1/DC3 Disabled Enabled

1-8 Power ON

Baud 1-1 1-2

2400BPS OFF OFF

4800BPS OFF ON

9600BPS ON ON

19200BPS ON OFF

Mode 1-8 ON Power On

DC1/DC3 Disabled Disabled Printer selected

DC1/DC3 Disabled ON Printer selected

OFF Printer de-selected

Addressable ON Printer de-selected

OFF Printer selected

*1 The old type is selected.

– 10 –

(2) RS-422A interface

This board had two DIP switches: one 8-bit switch and one 4-bit switch.

DIP switch #1 (8 bits):

Identical to the DIP switch on the RS-232C. (Bit 1-7 is disabled.)

DIP switch #2 (4 bits):

SW2-1 SW2-2 SW3-3 SW2-4

DC1,3 off ON ON ON ON

Address #1 OFF ON ON ON

#2 ON OFF ON ON

#3 OFF OFF ON ON

#4 ON ON OFF ON

#5 OFF ON OFF ON

#6 ON OFF OFF ON

#7 OFF OFF OFF ON

#8 ON ON ON OFF

#9 OFF ON ON OFF

#10 ON OFF ON OFF

#11 OFF OFF ON OFF

#12 ON ON OFF OFF

#13 OFF ON OFF OFF

#14 ON OFF OFF OFF

DC1,3 mode on OFF OFF OFF OFF

* DIP-SW #2 overrides the DIP-SW #1 DC1/3 setting (bit 1-7).

* DIP-SW #2 factory setting: All ON

(3) Parallel (Centronics) interface

The parallel-interface board has no DIP switches.

Table des matières

Autres manuels Star Micronics Imprimante

Star Micronics

Star Micronics XB24-10 Manuel utilisateur

Star Micronics

Star Micronics TSP1000 Series Guide de référence rapide

Star Micronics

Star Micronics LC-90 Manuel utilisateur

Star Micronics

Star Micronics Multi-Font NX-2410 Manuel utilisateur

Star Micronics

Star Micronics WinType 800C Manuel utilisateur

Star Micronics

Star Micronics LC24-10 Manuel utilisateur

Star Micronics

Star Micronics TSP600 Series Manuel utilisateur

Star Micronics

Star Micronics ND-10/15 Manuel utilisateur

Star Micronics

Star Micronics TSP400 Series Manuel d'utilisation et d'entretien

Star Micronics

Star Micronics NP-215 Manuel utilisateur

Star Micronics

Star Micronics TSP700 Series Manuel utilisateur

Star Micronics

Star Micronics DP8340RC Series Manuel utilisateur

Star Micronics

Star Micronics TSP143LAN Manuel

Star Micronics

Star Micronics NX-2460 Manuel utilisateur

Star Micronics

Star Micronics NB24-10/15 Manuel utilisateur

Star Micronics

Star Micronics TUP900 Series Manuel utilisateur

Star Micronics

Star Micronics LC-4511 Manuel utilisateur

Star Micronics

Star Micronics TSP650II SERIES Manuel utilisateur

Star Micronics

Star Micronics SM-L300 Guide de démarrage rapide

Star Micronics

Star Micronics NX-2420 Multi-Font Manuel utilisateur

Star Micronics

Star Micronics DP8340 Series Manuel utilisateur

Star Micronics

Star Micronics TSP800 Series Manuel utilisateur

Star Micronics

Star Micronics SR-10/I5 Manuel utilisateur

Star Micronics

Star Micronics NP-IO Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur