ST STM32U5 Manuel utilisateur
Introduction
The STM32U5 Nucleo-144 board based on the MB1549 reference board (order codes NUCLEO-U575ZI-Q and NUCLEO-
U5A5ZJ-Q) provides an affordable and flexible way for users to try out new concepts and build prototypes by choosing from the
various combinations of performance and power‑consumption features, provided by the STM32U5 microcontroller.
The ST Zio connector, which extends the ARDUINO® Uno V3 connectivity, and the ST morpho headers provide easy expansion
of the functionality of the STM32 Nucleo open development platform with a wide choice of specialized shields.
The STM32U5 Nucleo-144 board does not require any separate probe as it integrates the STLINK-V3E debugger/programmer.
The STM32U5 Nucleo-144 board comes with the STM32 comprehensive free software libraries and examples available with the
STM32CubeU5 MCU Package.
Figure 1. STM32U5 Nucleo-144 board
Picture is not contractual.
STM32U5 Nucleo-144 board (MB1549)
UM2861
User manual
UM2861 - Rev 5 - February 2023
For further information contact your local STMicroelectronics sales office. www.st.com
1Features
•STM32U5 series microcontroller (Arm® Cortex®-M33 at 160 MHz) in an LQFP144 package
• Internal SMPS to generate Vcore logic supply, identified by '-Q' suffixed boards(1)
• USB Type-C® sink device FS or HS depending on the microcontroller
• Three user LEDs
• RESET and USER push-buttons
• 32.768 kHz crystal oscillator
• Board connectors:
–USB Type-C® connector
–ST Zio connector including ARDUINO® Uno V3
– ST morpho extension pin headers for full access to all STM32 I/Os
• Flexible power-supply options: ST-LINK USB VBUS, USB connector, or external sources
• On-board STLINK-V3E debugger/programmer with USB re-enumeration capability: mass storage, Virtual
COM port, and debug port
• Comprehensive free software libraries and examples available with the STM32CubeU5 MCU Package
• Support of a wide choice of Integrated Development Environments (IDEs) including IAR Embedded
Workbench®, MDK-ARM, and STM32CubeIDE
1. SMPS significantly reduces power consumption in Run mode, by generating a Vcore logic supply from an internal DC/DC
converter.
Note: Arm is a registered trademark of Arm Limited (or its subsidiaries) in the US and/or elsewhere.
UM2861
Features
UM2861 - Rev 5 page 2/49
2Ordering information
To order an STM32U5 Nucleo-144 board, refer to Table 1. Additional information is available from the datasheet
and reference manual of the target STM32.
Table 1. Ordering information
Order code Board reference Target STM32
NUCLEO-U575ZI-Q MB1549 STM32U575ZIT6Q
NUCLEO-U5A5ZJ-Q STM32U5A5ZJT6Q
2.1 Products and codification
The meaning of the codification is explained in Table 1.
Table 2. Codification explanation
NUCLEO-XXYYZE-Q Description Example: NUCLEO-U575ZI-Q
XX MCU series in STM32 Arm Cortex MCUs STM32U5 Series
YY MCU product line in the series STM32U575/585
Z STM32 package pin count 144 pins
E
STM32 flash memory size:
• I for 2 Mbytes
• J for 4 Mbytes
2 Mbytes
-Q STM32 has an internal SMPS function SMPS
The order code is mentioned on a sticker placed on the top or bottom side of the board.
UM2861
Ordering information
UM2861 - Rev 5 page 3/49
3Development environment
3.1 System requirements
• Multi‑OS support: Windows® 10, Linux® 64-bit, or macOS®
• USB Type-A or USB Type-C® to Micro-B cable
Note: macOS® is a trademark of Apple Inc., registered in the U.S. and other countries and regions.
Linux® is a registered trademark of Linus Torvalds.
Windows is a trademark of the Microsoft group of companies.
3.2 Development toolchains
•IAR Systems® - IAR Embedded Workbench®(1)
•Keil® - MDK-ARM(1)
• STMicroelectronics - STM32CubeIDE
1. On Windows® only.
UM2861
Development environment
UM2861 - Rev 5 page 4/49
4Conventions
Table 3 provides the conventions used for the ON and OFF settings in the present document.
Table 3. ON/OFF convention
Convention Definition
Jumper JPx ON Jumper fitted
Jumper JPx OFF Jumper not fitted
Jumper JPx [1-2] Jumper fitted between Pin 1 and Pin 2
Solder bridge SBx ON SBx connections closed by 0 Ω resistor
Solder bridge SBx OFF SBx connections left open
Resistor Rx ON Resistor soldered
Resistor Rx OFF Resistor not soldered
Capacitor Cx ON Capacitor soldered
Capacitor Cx OFF Capacitor not soldered
UM2861
Conventions
UM2861 - Rev 5 page 5/49
5Quick start
The STM32U5 Nucleo-144 board is a low-cost and easy-to-use development kit, to quickly evaluate and start
development with an STM32U5 Series microcontroller in an LQFP 144-pin package. Before installing and
using the product, accept the Evaluation Product License Agreement from the www.st.com/epla webpage. For
more information on the STM32U5 Nucleo-144 board and software example, visit the www.st.com/stm32nucleo
webpage.
5.1 Getting started
Follow the sequence below to configure the STM32U5 Nucleo-144 board and launch the software example (refer
to Figure 4 for component location):
1. Check the jumper position on the board (refer to Default board configuration).
2. Connect the STM32U5 Nucleo-144 board to a PC with a USB cable (USB Type-A or USB Type-C® to
Micro-B) through the USB connector (CN1) to power the board.
3. The 5V_PWR green (LD5) and COM (LD4) LEDs light up, and the green LED (LD1) blinks.
4. Press the blue user button (B1).
5. Observe how the blinking of the LEDs (LD1, LD2, and LD3) changes, according to the clicks on the button
(B1).
6. Download the software examples that help to use the STM32 Nucleo features. These are available on the
www.st.com website.
7. Develop your application using the available examples.
5.2 Default board configuration
By default, the STM32U5 Nucleo-144 board is configured with VDD_MCU at 3.3 V. It is possible to configure the
board with VDD_MCU at 1.8 V. Before switching to 1.8 V, ensure that the extension module and external shield
connected to the Nucleo-144 board are 1.8 V compatible.
The default jumper configuration and voltage setting are shown in Table 4.
Table 4. Default jumper configuration
Jumper Definition Default position Comment
JP1 STLK_NRST OFF STLINK-V3E is selected as the default
debugger.
JP2 T_NRST ON RST connected between MCU target
and debugger
JP4 VDD [1-2] VDD MCU voltage selection 3V3
JP5 IDD measurement ON MCU VDD current measurement
JP6 5V power selection [1-2] 5V from STLINK-V3E
JP7 UCPD_DBCC1 OFF Refer to Section 6.11.2 UCPD.
JP8 UCPD_DBCC2 OFF Refer to section Section 6.11.2 UCPD.
UM2861
Quick start
UM2861 - Rev 5 page 6/49
Figure 2. Default board configuration
UM2861
Default board configuration
UM2861 - Rev 5 page 7/49
Table 5 explains the other jumper settings and configurations.
Table 5. Jumper configuration
Jumper Definition Setting(1) Comment
JP1 STLK_RST
ON Use to reset the STLINK-V3E MCU
when an external debug probe is used.
OFF STLINK-V3E is selected as the default
debugger.
JP2 T_NRST
ON STLINK-V3E can reset the target
MCU.
OFF
STLINK-V3E cannot reset the target
MCU. Configuration to use when an
external debug probe is used.
JP4 VDD voltage selection
[1-2] VDD voltage selection is 3V3
[2-3] VDD voltage selection is 1V8
OFF No internal VDD power supply
(External 3.3 or 1.8 V needed)
JP5 IDD measurement
ON MCU is powered by the on‑board
power supplies.
OFF
Use an ammeter to measure the
VDD_MCU power consumption, or
connect a 3.3 or 1.8 V external
source on pin 2 (STLINK-PWR
tools with STM32CubeMonitor-Power or
ULPBench probe as exemple).
JP6 5V Power selection(2)
[1-2] 5V source from STLINK-V3E
[3-4] 5V source from ARDUINO® VIN 7-12V
[5-6] 5V source from 5V_EXT
[7-8] 5V source from USB Type-C®
[9-10]
5V source from USB_CHGR.
From STLINK-V3E USB connector
(CN1) without overcurrent protection.
OFF NO 5V power source, configuration
when external 3V3 is used.
JP7 UCPD_DBCC1
OFF UCPD_DBCC1 NOT connected to
GND
ON UCPD_DBCC1 connected to GND (For
debug purpose)
JP8 UCPD_DBCC2
OFF UCPD_DBCC2 NOT connected to
GND
ON UCPD_DBCC2 connected to GND (For
debug purpose)
1. The default configuration is in bold.
2. This is recommended to have only one jumper configuration.
UM2861
Default board configuration
UM2861 - Rev 5 page 8/49
6Hardware layout and configuration
The STM32U5 Nucleo-144 board is designed around an STM32U5 microcontroller in an LQFP 144-pin package.
Figure 3 shows the connections between the STM32 and its peripherals (STLINK-V3E, push‑buttons, LEDs, USB
ST Zio connectors, and ST morpho headers). Figure 4 and Figure 5 show the location of these features on the
STM32U5 Nucleo-144 board.
The mechanical dimensions of the board are shown in Figure 6.
Figure 3. Hardware block diagram
DT55010V1
STM32U5xxZx-Q
OSC_32
SWD
32 KHz
crystal
VCP
UART
GPIOs
GPIO
LED
GPIO
Embedded
STLINK-V3E
STDC14 / MIPI10
SWD VCP
UART
USB Micro-B
connector
B1
User
B2
Reset
ARDUINO®
ST morpho
GPIO
ARDUINO®
ST morpho
5V
PWR SEL
5V
LED
COM
T_NRST
STLK
NRST
LEDLED
IDD1V8 / 3V3
USB
Type-C®
connector
GND
GND
GNDGND
SWDUART
Note: VCP: Virtual COM port
SWD: Serial Wire Debug
UM2861
Hardware layout and configuration
UM2861 - Rev 5 page 9/49
6.1 STM32U5 Nucleo-144 board layout
Figure 4. STM32U5 Nucleo-144 board top layout
UM2861
STM32U5 Nucleo-144 board layout
UM2861 - Rev 5 page 10/49
Autres manuels pour STM32U5
2
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels ST Carte mère
ST
ST STM32100B-EVAL Manuel utilisateur
ST
ST STEVAL-MKI019V1 Manuel utilisateur
ST
ST STUSB03E Manuel utilisateur
ST
ST STM8T141-EVAL Manuel utilisateur
ST
ST STEVAL-ISC005V1 Guide de l'administrateur
ST
ST EVALSP1340CPU Manuel utilisateur
ST
ST STM32G474E-EVAL Manuel utilisateur
ST
ST STEVAL-ILL059V1 Manuel utilisateur
ST
ST SGS-Thomson ST624x-KIT Series Manuel utilisateur
ST
ST STM32MP157D-EV1 Manuel utilisateur
ST
ST UM2163 Manuel utilisateur
ST
ST STM3210E-EVAL Manuel utilisateur
ST
ST STM32F407 Series Manuel utilisateur
ST
ST EVAL-L99H02XP Manuel utilisateur
ST
ST STM32H753I-EVAL Manuel utilisateur
ST
ST STEVAL-ISB68WA Manuel utilisateur
ST
ST B-L4S5I-IOT01A Manuel utilisateur
ST
ST STM32 NUCLEO-F042K6 Manuel utilisateur
ST
ST X-NUCLEO-IDB05A1 Manuel utilisateur
ST
ST UM0527 Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
