ST X-NUCLEO-GFX01M Series Manuel utilisateur

Introduction

The X-NUCLEO-GFX01M1 and X-NUCLEO-GFX01M2 expansion boards (X-NUCLEO-GFX01Mx) add graphic user interface

(GUI) capability to STM32 Nucleo-64 boards.

They feature a 2.2" SPI QVGA TFT display as well as a 64-Mbit SPI NOR Flash memory for storing graphic images, texts and

texture. The expansion boards also offer a joystick for GUI navigation.

X-NUCLEO-GFX01M1 uses the ST morpho connector and supports only one SPI. It is compatible with the following

Nucleo-64 boards: NUCLEO-F030R8, NUCLEO-F070RB, NUCLEO-F072RB, NUCLEO-F091RC, NUCLEO-F401RE, NUCLEO-

F410RB, NUCLEO-F411RE, NUCLEO-F446RE, NUCLEO-G071RB, NUCLEO-L053R8, NUCLEO-L073RZ, NUCLEO-L412RB-

P, NUCLEO-L433RC-P, NUCLEO-L452RE, NUCLEO-L452RE-P, and NUCLEO-L476RG.

X-NUCLEO-GFX01M2 uses the ST morpho connector and suppports up to two SPIs. It is compatible with the following

Nucleo-64 boards, which include the X-NUCLEO-GFX01M1-compatible boards: NUCLEO-F030R8, NUCLEO-F070RB,

NUCLEO-F072RB, NUCLEO-F091RC, NUCLEO-F103RB, NUCLEO-F302R8, NUCLEO-F303RE, NUCLEO-F334R8, NUCLEO-

F401RE, NUCLEO-F410RB, NUCLEO-F411RE, NUCLEO-F446RE, NUCLEO-G070RB, NUCLEO-G071RB, NUCLEO-

G0B1RE, NUCLEO-G431RB, NUCLEO-G474RE, NUCLEO-G491RE, NUCLEO-L010RB, NUCLEO-L053R8, NUCLEO-

L073RZ, NUCLEO-L152RE, NUCLEO-L412RB-P, NUCLEO-L433RC-P, NUCLEO-L452RE, NUCLEO-L452RE-P, NUCLEO-

L476RG, NUCLEO-WB15CC, NUCLEO-WB55RG, and NUCLEO-WL55JC.

Figure 1. X-NUCLEO-GFX01Mx top view Figure 2. X-NUCLEO-GFX01Mx bottom view

Pictures are not contractual.

SPI display expansion boards for STM32 Nucleo-64

UM2750

User manual

UM2750 - Rev 2 - October 2021

For further information contact your local STMicroelectronics sales office. www.st.com

1Features

• 2.2" SPI QVGA TFT LCD

• 64-Mbit SPI NOR Flash memory

• Joystick for easy menu navigation

• Compatible with selected STM32 Nucleo-64 boards using the ST morpho interface

UM2750

Features

UM2750 - Rev 2 page 2/31

2Ordering information

To order the X-NUCLEO-GFX01Mx SPI display expansion boards for STM32 Nucleo-64, refer to Table 1.

Table 1. Ordering information

Order code Board reference Differentiating features

X-NUCLEO-GFX01M1

MB1642(1)

First-generation product compatible with a limited set of STM32 Nucleo-64 boards.

X-NUCLEO-GFX01M2 Second-generation product compatible with a broader set of STM32 Nucleo-64

boards.

1. MB1642B for X-NUCLEO-GFX01M1, MB1642D for X-NUCLEO-GFX01M2.

The STM32 Nucleo-64 boards feature STM32 32-bit microcontrollers based on the Arm® Cortex®‑M processor.

Note: Arm is a registered trademark of Arm Limited (or its subsidiaries) in the US and/or elsewhere.

UM2750

Ordering information

UM2750 - Rev 2 page 3/31

3Development environment

3.1 Demonstration software

The demonstration software supporting the X-NUCLEO-GFX01M1 and X-NUCLEO-GFX01M2 expansion boards

is available from the X-CUBE-DISPLAY STM32Cube Expansion Package and must be programmed into

the corresponding Nucleo board. The latest versions of the demonstration source code and associated

documentation can be downloaded from www.st.com.

UM2750

Development environment

UM2750 - Rev 2 page 4/31

4Quick start

Before the first use, make sure that no damage occurred to the board during shipment:

• All socketed components must be firmly secured in their sockets

• Nothing must be loose in the board plastic bag or in the box

To start using the X-NUCLEO-GFX01M1 or X-NUCLEO-GFX01M2 expansion board, follow the steps below:

1. Plug the board on a compatible STM32 Nucleo development board

2. Download the evaluation firmware and full set of documentation from www.st.com/en/product/x-cube-display

and program the target device

3. Evaluate the graphic possibilities of STM32 devices combined with the TouchGFX Engine graphic library in

X-CUBE-TOUCHGFX or develop your own application

UM2750

Quick start

UM2750 - Rev 2 page 5/31

5Hardware layout and configuration

Figure 3 and Figure 4 help users to locate the different features on the X-NUCLEO-GFX01M1 and X-NUCLEO-

GFX01M2 expansion boards (X-NUCLEO-GFX01Mx). The mechanical dimensions of the X-NUCLEO-GFX01Mx

products are shown in Figure 5.

Figure 3. X-NUCLEO-GFX01Mx PCB layout: top side

2.2" SPI QVGA

TFT LCD

(LCD1)

Menu navigation

joystick (B1)

UM2750

Hardware layout and configuration

UM2750 - Rev 2 page 6/31

Figure 4. X-NUCLEO-GFX01Mx PCB layout: bottom side

64-Mbit SPI NOR

Flash memory

(U1)

LCD ZIF

connector

(CN1)

ST morpho connectors

(CN2 and CN3)

UM2750

Hardware layout and configuration

UM2750 - Rev 2 page 7/31

Figure 5. X-NUCLEO-GFX01Mx mechanical drawing

UM2750

Hardware layout and configuration

UM2750 - Rev 2 page 8/31

5.1 Power supply

The X-NUCLEO-GFX01Mx is directly powered by a 3.3 V power supply provided by the Nucleo-64 development

board through pin 16 of the CN2 connector.

5.2 SPI QVGA TFT LCD (LCD1)

5.2.1 Description

The SPI QVGA TFT LCD is connected to a first SPI interface (SPIA) of the STM32 device.

X-NUCLEO-GFX01M1 and X-NUCLEO-GFX01M2 feature each a different LCD with a different controller IC.

Refer to the product history for details.

5.2.2 Operating voltage

The LCD is designed to operate only with a 3.3 V compatible SPI and GPIO interface.

5.2.3 I/O interface

Table 2. X-NUCLEO-GFX01M1 I/O configuration of the LCD

Pin number Pin name Signal name STM32 GPIO Function

1 LED_K4 - - Display backlight LED4 cathode

2 IM0 GND -

System interface selection: 4-line 8-bit data SPI mode

3 IM1 3V3 -

4 IM2 3V3 -

5 IM3 3V3 -

6 RESET DISP_NRESET_PA1 PA1(1) (2) Reset active low

7 - 28 - - - Not connected

29 SDO SPIA_MISO_PA6_PB14 PA6(1)

PB14(2) SPI master in/slave out

30 SDI SPIA_MOSI_PA7_PB15 PA7(1)

PB15(2) SPI master out/slave in

31 RD - - Not connected

32 RS/SCL SPIA_SCK_PA5_PB13 PA5(1)

PB13(2) SPI serial clock

33 WR SPIA_DCX_PB3_PB3 PB3(1) (2) SPI write enable

34 CS SPIA_NCS_PB5_PB5 PB5(1) (2) SPI chip select active high

35 FMARK DISP_TE_PA0 PA0(1) (2) Tearing effect output pin to synchronize MCU on frame

writing

36 VCC 3V3 - 3.3 V power supply

37 GND GND - Ground

38 LED_A 3V3 - Display backlight LED common anode

39 LED_K1 - - Display backlight LED1 cathode

40 LED_K2 - - Display backlight LED2 cathode

41 LED_K3 - - Display backlight LED3 cathode

42 - 45 - - - Not connected

1. STM32 GPIO for NUCLEO-F030R8, NUCLEO-F070RB, NUCLEO-F072RB, NUCLEO-F091RC, NUCLEO-F401RE,

NUCLEO-F410RB, NUCLEO-F411RE, NUCLEO-F446RE, NUCLEO-G071RB, NUCLEO-L053R8, NUCLEO-L073RZ,

NUCLEO-L452RE and NUCLEO-L476RG.

2. STM32 GPIO for NUCLEO-L412RB-P, NUCLEO-L433RC-P and NUCLEO-L452RE-P.

UM2750

Power supply

UM2750 - Rev 2 page 9/31

Table 3. X-NUCLEO-GFX01M2 I/O configuration of the LCD

Pin number Pin name Signal name STM32 GPIO Function

1 LED_K4 - - Display backlight LED4 cathode

2 IM0 GND -

System interface selection: 4-line 8-bit data SPI mode

3 IM1 3V3 -

4 IM2 3V3 -

5 IM3 3V3 -

6 RESET DISP_NRESET

PA1(1) (2) (3) (4) (5)

PB2(6)

PC1(7)

PA6(8)

Reset active low

7 - 28 - - - Not connected

29 SDO SPIA_MISO

PA6(1) (3) (5) (6) (7)

PB14(2) (4)

PB4(8)

SPI master in/slave out

30 SDI SPIA_MOSI PA7(1) (3) (5) (6) (7) (8)

PB15(2) (4) SPI master out/slave in

31 RD - - Not connected

32 RS/SCL SPIA_SCK PA5(1) (3) (5) (6) (7) (8)

PB13(2) (4) SPI serial clock

33 WR SPIA_DCX

PB10(1) (2) (4) (5) (6)

PB14(3)

PA8(7) (8)

SPI write enable

34 CS SPIA_NCS

PA9(1) (2) (3) (5)

PB6(4)

PC2(6)

PC12(7)

PB5(8)

SPI chip select active high

35 FMARK DISP_TE

PA0(1) (2) (3) (4) (5)

PB1(6)

PC0(7)

PA4(8)

Tearing effect output pin to synchronize MCU on frame writing

36 VCC 3V3 - 3.3 V power supply

37 GND GND - Ground

38 LED_A 3V3 - Display backlight LED common anode

39 LED_K1 - - Display backlight LED1 cathode

40 LED_K2 - - Display backlight LED2 cathode

41 LED_K3 - - Display backlight LED3 cathode

42 - 45 - - - Not connected

1. STM32 GPIO for NUCLEO-F030R8, NUCLEO-F070RB, NUCLEO-F072RB, NUCLEO-F091RC, NUCLEO-F103RB,

NUCLEO-F303RE, NUCLEO-F334R8, NUCLEO-F401RE, NUCLEO-F410RB, NUCLEO-F411RE, NUCLEO-F446RE,

NUCLEO-L053R8, NUCLEO-L010RB, NUCLEO-L152RE, NUCLEO-L073RZ, NUCLEO-L452RE and NUCLEO-L476RG.

2. STM32 GPIO for NUCLEO-F302R8.

3. STM32 GPIO for NUCLEO-G070RB, NUCLEO-G071RB and NUCLEO-G0B1RE.

4. STM32 GPIO for NUCLEO-L412RB-P, NUCLEO-L433RC-P and NUCLEO-L452RE-P.

5. STM32 for NUCLEO-G431RB, NUCLEO-G474RE and NUCLEO-G491RE.

6. GPIO for NUCLEO-WL55JC.

7. GPIO for NUCLEO-WB55RG.

8. GPIO for NUCLEO-WB15CC.

UM2750

SPI QVGA TFT LCD (LCD1)

UM2750 - Rev 2 page 10/31

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ST Matériel informatique

ST STM32F4 Series Manuel utilisateur

ST X-NUCLEO-IHM01A1 Manuel utilisateur

ST X-NUCLEO-BNRG2A1 Manuel utilisateur

ST STM32H7 Series Manuel du propriétaire

ST X-NUCLEO-IHM09M1 Manuel utilisateur

ST ST7-EMU3 Series Manuel utilisateur

ST I-CUBE-LRWAN Manuel utilisateur

ST EVALSPEAr320HMI Manuel utilisateur

ST X-NUCLEO-IHM09M2 Manuel utilisateur

ST X-NUCLEO-OUT02A1 Manuel utilisateur

ST STEVAL-SCR002V1 Manuel utilisateur

ST STA309A Manuel utilisateur

ST X-NUCLEO-OUT08A1 Manuel utilisateur

ST X-NUCLEO-S2915A1 Manuel utilisateur

ST X-CUBE-SBSFU Manuel utilisateur

ST STEVAL-C34KAT1 Manuel utilisateur

ST STR91 Series Instructions d'installation et d'utilisation

ST X-NUCLEO-IDS01A4 Manuel utilisateur

ST STEVAL-C34KAT2 Manuel utilisateur

ST STM32 ODE Manuel utilisateur

ST X-NUCLEO-IKA01A1 Manuel utilisateur

ST X-NUCLEO-OUT04A1 Manuel utilisateur

ST X-NUCLEO-LED12A1 Manuel utilisateur

ST STEVAL-BCN002V1B Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

Advantech

Advantech ASMB-935 Series Manuel utilisateur