SSS Siedle IDorSS-5100 Manuel utilisateur

Version 06/2017 1

Mounting Instructions

iDorSS-5100



Version 06/2017 2

1 Preparations

1.1 Scope of delivery

•iDorSS-5100 device

•2 release tools

optional

•Surface mount housing

•Spring-loaded mounting brackets for hollow-wall mounting

1.2 Location

•Suitable for indoor and outdoor use ( -4°F bis +140°F temperature range).

•Due to the sunlight readable display, the device is qualified for high ambient light

intensity. Sunlight (sunrise and sunset) pointing directly into the lens has to be

avoided:

•Recommended mounting height: approx. 61.8” middle of back housing



Version 06/2017 3

1.3 Interfaces

All connections are located on the rear of the panel

1.3.1 Ethernet, Power over Ethernet

Ethernet connection through Ethernet jack. Use a PoE-enabled

switch or a PoE injector for power supply over Ethernet (PoE).

1.3.2 2Wire-Connection

If the unit was ordered with the 2Wire option, connect the 2

installation wires to the 2Wire terminals. In case of long distances

ensure a sufficient AWG cable. (www.idorss.com)

1.3.3 Circuit board connections

•Ethernet, 10/100BaseT with RJ45-jack

•2-wire-jack (with optional 2Wire Kit)

•Wiegand or RS485 or UART Tx/Rx

•2 x Trigger inputs

•1 x Relais - e.g. door release

•USB-OTG for extensions!

Inp1 Inp2 Tamper GND

Inputs are biased HIGH and need to be pulled LOW to GND for trigger!

2WIRE

12-55V DC

Wiegand Relay

GND Dat1 Dat0 NC COM NO



Version 06/2017 4

2 Wall mounting

Flush mounting

The dimensions are width 3.74” x height 7.76” and a total depth of 1.42”.

Wall cutout dimensions are 7.2” x 3.27”.

The unit protrudes approx. 0.31” from the wall.

For uneven surfaces we recommend to surface mount the unit. When flush

mounting it, make sure the tabs on the rear housing are positioned on the top and

bottom of the wall surface.

Loosen with the release tool the back

box: Insert the tool with the lugs into

the respective openings on the left

and right and press unit the front part

is released.

Front part can now be lifted off.

Attention - In case the units is still

connected !



Version 06/2017 5

The back box can be used as a drilling

template.

Cable inlet through the large round

opening

Fasten the back box

Connect the cable to the circuit board

on the front part.

Fasten the front part to the back till it

clips in.



Version 06/2017 6

Surface mounting (optional)

The surface mount procedure is the same except no wall cutout is

necessary. The device is screwed directly onto the wall. The back part

consists of the surface mount housing.

Hollow-wall mounting (optional)

The Hollow-wall mounting procedure is the same as the flush mounting procedure.

Wall cutout dimensions are 7.2” x 3.27”. The back part consists of

a pre-assembled spring plates. The spring plates must be led

through the wall outlet. The springs are tightened by tightening

the screws.

When Hollow-wall mounted it needs to be assured that the upper and lower flaps of

the back box stay outside the wall opening. The housing protrudes over the wall

surface.

3 Configuration

Configuration and operating instructions available on www.idorss.com

Table des matières

Autres manuels SSS Siedle Système d'interphone

SSS Siedle

SSS Siedle CV 850-1 Manuel utilisateur

SSS Siedle

SSS Siedle BVI 750-0 Instructions de montage

SSS Siedle

SSS Siedle BVI 750-0 Instructions de montage

SSS Siedle

SSS Siedle BTLE 050-03 Guide de l'utilisateur

SSS Siedle

SSS Siedle DoorCom Analog Series Manuel d'installation

SSS Siedle

SSS Siedle DoorCom IP DCIP 650-0 Manuel utilisateur

SSS Siedle

SSS Siedle CSV 850-1 A Manuel utilisateur

SSS Siedle

SSS Siedle Siedle Scope S 850-0 Manuel utilisateur

SSS Siedle

SSS Siedle BTLM 630-0 Manuel utilisateur

SSS Siedle

SSS Siedle Basic CVB 850-1 Manuel utilisateur

SSS Siedle

SSS Siedle Vario SET VVP 850-1-01 Manuel utilisateur

SSS Siedle

SSS Siedle ST 10-0 Manuel utilisateur

SSS Siedle

SSS Siedle BVPS 850-0 Manuel utilisateur

SSS Siedle

SSS Siedle BAA 650-0 Manuel utilisateur

SSS Siedle

SSS Siedle BVI 750-2 Instructions de montage

SSS Siedle

SSS Siedle Siedle Steel STLM 645-02 Manuel utilisateur

SSS Siedle

SSS Siedle HT 644-01 Manuel utilisateur

SSS Siedle

SSS Siedle HTCV 811-0 Manuel utilisateur

SSS Siedle

SSS Siedle NG 602-01 Manuel utilisateur

SSS Siedle

SSS Siedle DCA 650-02 Manuel d'installation

SSS Siedle

SSS Siedle MO 950-0/9 Manuel utilisateur

SSS Siedle

SSS Siedle Compact CV 850-1-02 E Manuel utilisateur

SSS Siedle

SSS Siedle Compact Select CSV 850 Series Manuel utilisateur

SSS Siedle

SSS Siedle SET CVB 850-1 E/W Manuel utilisateur

Manuels Système d'interphone populaires d'autres marques

Bticino

Bticino LINEA 3000 Manuel utilisateur

MSI

MSI MSI-140 Manuel utilisateur

golmar

golmar Stadio Plus Manuel utilisateur

CyberData

CyberData 011211 series Manuel

Vidos

Vidos duo M1021 Manuel utilisateur

Vimar

Vimar ELVOX 7539/E Manuel utilisateur

Dahua

Dahua VTO Series Manuel utilisateur

Elvox

Elvox 5651 Manuel utilisateur

Videx

Videx VIDEOKIT Series Manuel utilisateur

Rocom

Rocom Doortello Business FW T2.05W2.04 Manuel utilisateur

Viking

Viking E-35-EWP Manuel utilisateur

Safeguard Supply

Safeguard Supply LRA-EX1000 Manuel utilisateur

GRD

GRD MAX V2 Manuel utilisateur

Alecto

Alecto ADI-250 Manuel utilisateur

Aiphone

Aiphone IE-8MD Manuel utilisateur

Perel

Perel EDB4 Manuel utilisateur

Bticino

Bticino Classe 300 Manuel utilisateur

LG L5142 Manuel utilisateur

SSS Siedle iDorSS-5100 Manuel utilisateur

Manuels Système d'interphone populaires d'autres marques