SPEED LEADER LVP8000 Manuel utilisateur
User Manual
LVP8000
LED Splicing Processor
SHENZHEN SPEEDLEADER TECHNOLOGY
About the Manual
Without the written permission of the company, it is forbidden for any company or
individual to imitate, copy, or transcribe part or all of the contents of the manual. It is not
allowed to have the commodity publicity or achieve any commercial or profit-seeking
purpose in any form (electronic form, mechanical form, photocopying form, recording
form, or other possible ways).
Please carefully read this manual before using this equipment. All the product
specifications and information mentioned in the manual are only for reference. If there is
the content updating, the company will not make further notice. Unless there is a special
agreement, this manual is only taken as an instruction, and all statements and information
will not constitute a guarantee of any kind.
Brand Royalty
VGA and XGA are the registered trademarks of IBM Corporation.
VESA is a trademark of the Video Electronics Standards Association.
The logo of HDMI and High-Definition Multimedia Interface are the trademark of HDMI
Licensing LLC.
Safety Instructions
This symbol prompts the user that there are the important operation and
maintenance instructions in the user manual.
Page 1 of 56
S
HENZHEN
S
PEEDLEADER TE
C
HN
O
L
O
G
Y
CO
.
,
LTD. LED Vi
deo
Pr
ocesso
r
This symbol warns the user that there is the hazardous voltage exposed inside
the equipment and there is the electric shock hazard.
This equipment must be connected with ground wire.
This equipment needs a rated power voltage. Ensure that the input voltage
error should be between - 10% and +10%.
Do not connect AC power cord with another AC power cord which may lead to
excessive noise.
Please use the equipment when the surrounding temperature is from -10 ℃to
45 ℃, and the relative humidity is 90% or less than that.
Do not use this equipment in certain special circumstances, such as, closing to
a heat source, which may cause overheating of the equipment and damage it.
Please use it in a well-ventilated place and pay attention not to block the
equipment vents.
Do not expose this equipment in the place which has the possibility for
accidental collision or vibration, and reinforcement processing is necessary in
the vibration place.
When you use the equipment, please make sure that there are no objects, such
as water and metal objects, inside the equipment. Otherwise, it will damage the
equipment and cause a fire.
If there is any irregularity or abnormality for the equipment, please
immediately turn off the power supply, disconnect the AC power cord, and see
“Trouble Clearing”.
If this equipment is damaged, do not disassemble it. Please contact our
maintenance service department.
Page 2 of 56
S
HENZHEN
S
PEEDLEADER TE
C
HN
O
L
O
G
Y
CO
.
,
LTD. LED Vi
deo
Pr
ocesso
r
Contents
Overview ..............................................................................................................................4
Application...........................................................................................................................5
Installation ...........................................................................................................................7
Install LED Sending Card................................................................................................7
Install LVP8000 ..............................................................................................................8
Rear Panel .......................................................................................................................9
Operation Interface………………………………………………………………………. 13
Menu System..........................................................................................................………..17
Menu System Overview ................................................................................................17
Enter the Menu ..............................................................................................................18
Automatic Menu............................................................................................................19
Input Menu ....................................................................................................................20
Output Menu..................................................................................................................22
Splice Menu...................................................................................................................23
Function Menu ..............................................................................................................26
Advanced Menu ...........................................................................................................28
Preset Menu...................................................................................................................30
System Menu.................................................................................................................31
Operation ...........................................................................................................................32
Factory Resetting...........................................................................................................32
Output Resolution setting ..............................................................................................33
Select the Input..............................................................................................................34
Page 3 of 56
S
HENZHEN
S
PEEDLEADER TE
C
HN
O
L
O
G
Y
CO
.
,
LTD. LED Vi
deo
Pr
ocesso
r
Preview and Seamless Switching ..................................................................................36
Set Fade Time and Preview Switching Mode................................................................38
Adjust Output Window Position....................................................................................38
Crop Size and Position of Output Window....................................................................39
Brightness and Contrast of Output Window ..................................................................41
Save and Recall of the Preset.........................................................................................43
Splicing Setting and Application ...................................................................................45
Specifications .....................................................................................................................51
Trouble Clearing................................................................................................................55
Page 4 of 56
S
HENZHEN
S
PEEDLEADER TE
C
HN
O
L
O
G
Y
CO
.
,
LTD. LED Vi
deo
Pr
ocesso
r
Overview
LVP8000 is a powerful four-channel splicing processor, which can support four
independent video processors, 4×4 channel hybrid matrix and 4096×2304 high-resolution
picture output. For a single processor, it can splice a maximum of 10240 × 960 or 4096 ×
2304 or 1920 × 4800 picture output, which is much higher than 8M video output. It is the
ideal video demonstration equipment, which can be applied to large-scale performance,
command, control center, video conference, medical facility, meeting room and court.
LVP-8000 can accommodate a wide range of input source, with four-channel
independent picture processing engine and four-channel fully configurable input, which
can switch in sixteen-channel video input, including four-channel DVI, four-channel VGA,
four-channel VID and four-channel 3G-SDI (optional). Every channel can receive standard
resolution or high-resolution video signal, with the maximum resolution input reception of
1920 x 1200 @ 60Hz.
LVP-8000 can output four-channel video with rich interfaces. The output applies DVI-I
and DVI-D interface, which can realize two-channel DVI and one-channel VGA (using
DVI to VGA connector to connect the DVI-I interface) and meet more device attachment.
The output resolution of each channel can be set by the user, with the maximum output of
1920 x 1200 @ 60Hz or 2048 x 1152 @ 60Hz resolution, which can meet various
high-definition performances. LVP-8000 can achieve different kinds of splice modes, such
as, equal splice, unequal splice, super wide and super high splice, simplifying user’s
installation.
Four-channel independent picture processor is internally installed in LVP-8000 with
powerful video processing and switching function, which can achieve single-input to
multiple-output or multiple-input to multiple-output video switch, equal to a 4 × 4 channel
hybrid matrix. LVP-8000 can be configured into four independent video processors to
reduce the use of a large number of video processors and improve the performance quality.
Page 5 of 56
S
HENZHEN
S
PEEDLEADER TE
C
HN
O
L
O
G
Y
CO
.
,
LTD. LED Vi
deo
Pr
ocesso
r
Users can define seamless switching of any channel. Users can choose two outputs and
set them as Preview and program, by which seamless switching can be perfectly achieved.
LVP-8000 is easier to use with powerful functions and humanist design. If users touch
the keystroke and menu system, they can complete the complicated settings. The complete
setting and operation can be achieved by front keystroke, RS-232 and IP Link. LVP-8000
provides rich physical interfaces to meet the requirements of output equipment and
provides installation sites for more than four LED sending cards, which simplifies lots of
setting and installation. The knob can quickly adjust the frame parameters, which is
convenient for the users.
Application
Figure 1-1 shows a typical application of LVP-8000 splicing processor. LVP-8000
can receive a variety of signal and resolution input and support SD resolution to HD
resolution video input as follows:
zVGA (XGA, WUXGA) video
zDVI (compatible HDMI 1.3)
zComposite video (NTSC, PAL, SECAM)
zSD/HD/3G-SDI (optional)
Page 6 of 56
S
HENZHEN
S
PEEDLEADER TE
C
HN
O
L
O
G
Y
CO
.
,
LTD. LED Vi
deo
Pr
ocesso
r
Figure 1-1 Application of LVP-8000 Splicing Processor
LVP-8000 with various input and output interfaces, can access VGA and DVI signals
of the desktop computer, VGA and HDMI signal of the laptop, SDI signal of
high-definition camera, DV and DVD video signal. At the same time, LVP-8000 has
four-channel output. Each channel has tow DVI interfaces, which can realize two-channel
DVI and one-channel VGA signal (DVI/VGA interface is multiplexed interface, which has
DVI and VGA signal output) and meet user’s needs.
Four-channel output of LVP-8000 sends to the LED sending card and sending card
will then connect the LED video wall. There are four installation location for LED sending
card and four 5V Direct Current supply in it. According to configuration, users can take
any tow-channel output as switch with preview. When necessary, users can use software or
console to fully control LVP-8000.
Page 7 of 56
S
HENZHEN
S
PEEDLEADER TE
C
HN
O
L
O
G
Y
CO
.
,
LTD. LED Vi
deo
Pr
ocesso
r
Installation
Install LED Sending card
1. Remove the chassis cover, get rid of the chassis bezel and install fixed double-screw
bolt in the correspondence position in order to load the corresponding brand sending card.
Figure 2-1 Install LED Sending Card and Remove the Cover
2. Install LED Sending Card and fix it with the supplied M3 screws, then plug the 5V
power supply cable into electric outlet of Sending Card, as shown in the picture. After
installing the Sending Card, install the chassis bezel.
Page 8 of 56
S
HENZHEN
S
PEEDLEADER TE
C
HN
O
L
O
G
Y
CO
.
,
LTD. LED Vi
deo
Pr
ocesso
r
Figure 2-2 Install LED Sending Card
Install LVP-8000
The user can choose whether to install LVP-8000 to the rack or flight case. LVP-8000
has a standard 2U chassis, with the size of 8.8cm (Height) x 44cm (Width) x 33CM
(Depth). While installing, please avoid scratching the case and use cushion for fixing
suspension loop.
5V power supply
Table des matières
Autres manuels SPEED LEADER Matériel informatique
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
