Speco H8D7M Manuel utilisateur

User Manual

Thank you for purchasing our product. Speco Technologies is constantly developing and

improving products. We reserve the right to modify product design and specifications

without notice and without incurring any obligation.

H8D7M/H8B7M/H8T7M

Warnings

■

Speco Technologies is not responsible for any problems caused by improper operation or repair.

■

■ All installation and operation here should conform to local electrical safety codes.

■ Make sure the power supply voltage is correct before using the camera.

■ Do not drop the camera or subject it to physical shock.

■ Do not use the device beyond specified voltage range.

■ Do not place the camera in extremely hot, cold (the operating temperature shall be (-22˚F~122˚F), dusty or

damp locations, and do not expose it to high electromagnetic radiation.

■ To avoid heat accumulation, good ventilation is required for operating environment.

If the product does not work properly, please contact the dealer or where the product was purchased.

Keep away from liquid while in use.

sensitivity, low noise and distortion and supports HD video transmission with the common coaxial cable,

ensuring the requirement of the HD monitoring in the traditional surveillance system.

This camera series is the latest technology and advanced circuit design, which features high definition and

Introduction

● High Resolution

Adopt high performance sensor, providing high definition and clear image.

● High Transmission Performance

Real-time transmission with high speed and long distance.

● High Light Compensation (HLC)

Mask and compensation the high light area.

● DNR

Reduce noise from brightness and color signal.

● OSD

Access the camera settings which can be clearly displayed through the main menu.

● White Balance

Adjust the color temperature according to the environment automatically.

● ICR Auto Switch

The filter will filter infrared light during the daytime and change to normal at night to

ensure a high sensitivity and clear image.

● AGC

Adjust the gain of amplifier, enabling the camera to output the standard video signal in different

lighting condition.

● Backlight Compensation (BLC)

When the back of the captured object is too much bright, you can set BLC for the captured object to

make it clearer.

Cables

Power Cable

Video Output

Video Switch Cable

Video Switch: Four video output modes can be optional--AHD, TVI, CVI and CVBS

(a) remove the cover of the video switch cable; (b) hold and press the button in the video

switch cable for 5 seconds to switch the current video output.

Before you start, please make sure that the wall or ceiling is strong e nough to withstand three times

the weight of the camera. Please install and use the camera in the dry environment.

You’d better install back the lens cover or lower dome less than 4 hours after removing it.

The mounting types of cameras are only for reference.

Installation

►Mounting for H8B7M

1. Drill the screw holes and the cable hole on the wall according to the drill template.

2. Route and connect the cables .

3. Secure the mounting base with camera to the wall with screws as shown below.

∅4.6

48mm

4. Bracket adjustment. Before adjustment, preview the image of the camera on a monitor and then loosen the

fixed ring to adjust the view angle of the camera. Tighten the fixed ring after the adjustment.

►Mounting for H8D7M

Rubber plug

90° Tilt

360° Rotation 360° Pan

Fixed Ring

∅4.6

90.2mm

and the cable hole on the wall according to the drill template.

2. Rotate the trim ring anticlockwise to remove it from the camera.

Attach the drill template to the place where you want to fix the camera and then drill the screw holes

Trim ring

Rubber plug

Lower dome

* Install it when routing the

cables through the ceiling.

3. Loosen the screws to open the lower dome. Then route and connect the cables.

4. Secure the camera to the wall with screws provided as shown below.

5. Three-axis adjustment. Before adjustment, preview the image of the camera on a monitor and then

adjust the camera according to the figure below to get an optimum angle.

Turn

Rotation 0°~345°

Tilt 0°~77°

Pan 0°~345°

6. Install the lower dome back to the camera and fix it with screws. Then put the trim ring onto the lower

dome and then rotate it clockwise until it is locked. Finally, remove the protection film softly.

Trim ring

►Mounting for H8T7M

1. Loosen the fixed screw to disassemble the camera.

Fixed Screw Mounting Base

Enclosure

Dome

Drill the screw holes and the cable hole on the wall according to the drill template.

3 Route and connect the cables. Then secure the mounting base to the ceiling or wall with the screws provided.

Ø107.7

Ø5.0

Ø79.4

56.1

(mm)

angle. Finally, secure the camera with the fixed screw.

Install the dome and enclosure to the mounting base and then adjust the dome to obtain an optimum view

Tilt: 0˚~80˚

Rotate: 0˚~360˚

Turn

Pan: 0˚~360˚

Fixed

screw

Specifications

Camera

Image Sensor

Resolution

Image size

Video Output

Image System

Electronic Shutter

IR Distance (feet)

Frame Rate

Min. Illumination

Lens

Lens Mount

S/N Ratio

Ingress Protection

Functions

Function Control

Day &Night

WDR

Digital NR

AGC

Auto White Balance

Defog

BLC

Contrast

Saturation

Sharpness

Smart IR

Image Setting

Defect Correction

Others

Power Supply

1/2.5" CM S

8MP

3840×2160

AHD/TVI/CVI/CVBS (*camera comes defaulted to HD-TVI)

PAL/NTSC

Auto; 1/50s~1/100000s(PAL);1/60s~1/100000s (NTSC)

98~164

15fps

Color:0.01lux@F1.2, AGC ON; B/W: 0lux with IR

D14

≥ 52dB(AGC OFF)

IP67

OSD (UTC control)

ICR

Yes

Auto

DC12V (± 10%)

IR OFF: < 2W;

Specifications

Models H8B7M H8D7M

Ф5.55 3.94×

8.57 3.17× × 3.17

2.8~12mm (motorized)

IP67&IK10

IR OFF: < 2W; IR OFF: < 2W;

65~98

IP67

Power Consumption

Dimensions (inch)

Working Environment

IR ON : < 5.5W

-22 °F ~ 122 °F, 10 % ~ 90 %(relative humidity)

IR ON : < 5W IR ON : < 4.5W

98~164

H8T7M

Ф4.38 3.92×

Model:

Federal Communications Commission (FCC) Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

This device must accept any interference received, including interference that may

cause undesired operation.

FCC Responsible Party:

Speco Technologies

200 New Highway

Amityville, NY 11701

www.specotech.com

H8B7M/H8D7M/H8T7M

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Speco Caméra de sécurité

Speco

Speco HT-INTD8 Manuel utilisateur

Speco

Speco CVC5725DNV Manuel utilisateur

Speco

Speco WDRB1 Manuel utilisateur

Speco

Speco CVC-510C Manuel utilisateur

Speco

Speco VIP2B3 Manuel utilisateur

Speco

Speco CVC-3805 Manuel utilisateur

Speco

Speco O8FBMS1 Manuel utilisateur

Speco

Speco VL-265PIR Manuel utilisateur

Speco

Speco O4iD1 Manuel utilisateur

Speco

Speco HTINT40T1 Manuel utilisateur

Speco

Speco 650Line Intensifier3 HTINTB8G Manuel utilisateur

Speco

Speco x20 HD-SDI PTZ Outdoor Manuel utilisateur

Speco

Speco Intensifier HTINT59K1 Manuel utilisateur

Speco

Speco Intensifier H HINT81H Manuel utilisateur

Speco

Speco ZIP2B Guide d'installation

Speco

Speco CVC-637EX Manuel utilisateur

Speco

Speco O4iT1M Manuel utilisateur

Speco

Speco VIP2B1M Manuel utilisateur

Speco

Speco CILT13D1G Manuel utilisateur

Speco

Speco HTINTT5H Manuel utilisateur

Speco

Speco O5DH Guide de référence

Speco

Speco 960H 700TVL Manuel utilisateur

Speco

Speco O4FB1 Manuel utilisateur

Speco

Speco VLD8SCSFF Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur