spacewalker HOT-671 Manuel utilisateur
HOT-671
Pentium™IIprocessor
Based AGPMAINBOARD
User's Manual
2
FCC Notice:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy. If not installed and used properly, in strict accor-
dance with the manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures :
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help and for additional suggestions.
The user may find the following booklet prepared by the Federal Communications Commission helpful “How to Identify
and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office.
Washington, DC 20402, Stock 004-000-00345-4
FCCWarning
The user is cautioned that changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate this equipment.
Note: InorderforaninstallationofthisproducttomaintaincompliancewiththelimitsforaClassBdevice,shielded
cablesandpowercordmustbeused.
CE Notice:
Following standards were applied to this product, in order to achieve compliance with the electromagnetic
compatibility :
- Immunity in accordance with EN 50082-1: 1992
- Emissions in accordance with EN 55022: 1987 Class B.
NOTICE
Copyright 1998.
All Right Reserved
Manual Ver 1.0
All information, documentation, and specifications contained in this manual are subject to change without prior
notification by the manufacturer.
The author assumes no responsibility for any errors or omissions which may appear in this document nor does
it make a commitment to update the information contained herein.
TRADEMARKS
Intel is a registered trademark of Intel Corporation
PentiumII Processor is a registered trademark of Intel Corporation
PC/AT is a registered trademark of International Business Machine Corporation.
PS/2 is a registered trademark of IBM Corporation.
All other brand and product names referred to in this manual are trademarks or registered trademarks of their
respective holders.
3
TABLEOFCONTENTS
T
T
PREFACE ...................................................................................................................4
CHAPTER 1 INTRODUCTION ...........................................................................................5
Specification ....................................................................................................................................... 5
Accessories of HOT-671 .................................................................................................................... 7
CHAPTER 2HARDWARE CONFIGURATION........................................................................8
ThePentiumII &Celeron Processor ................................................................................................. 8
Whatdoesthe RM(RetentionMechanism) consistof ..................................................................... 9
InstalltheRetention MechanismandHeat SinkSupport ...............................................................10
InstallPentiumIIProcessor ............................................................................................................. 12
Celeron Processor S.E.P.P only RM Assembly Procedure .............................................................13
WhatdoesCeleron Processor RMconsistof .................................................................................. 14
Installthe CeleronProcessorRM. ................................................................................................... 14
InstallCeleronProcessor.................................................................................................................. 15
Jumpers ............................................................................................................................................. 16
CPUClockSpeed Selection -JP2and JP6......................................................................................16
ClearCMOS- JP11 .......................................................................................................................... 18
FlashEEPROMVpp - JP8 ............................................................................................................... 18
Keyboard&PS/2 Mousepower-onsetting(option)........................................................................ 19
Connectors ........................................................................................................................................ 19
CHAPTER 3MEMORY CONFIGURATION .........................................................................22
CHAPTER 4 FLASH UTILITY ........................................................................................23
CHAPTER 5 AWARD BIOS SETUP ..............................................................................25
The Main Menu ................................................................................................................................ 26
StandardCMOSSetup...................................................................................................................... 28
BIOS Features Setup......................................................................................................................... 30
ChipsetFeatures Setup ..................................................................................................................... 33
PowerManagementSetup ................................................................................................................ 36
PCIConfigurationSetup .................................................................................................................. 38
IntegratedPeripherals ....................................................................................................................... 40
PasswordSetting............................................................................................................................... 43
CHAPTER 6 ONBOARD SOUND CHIP SETTING .............................................................44
Introduction....................................................................................................................................... 44
Features ............................................................................................................................................. 44
SystemRequirements ....................................................................................................................... 45
ConnectingAudioDevices to 671BackPanel................................................................................ 46
Windows 95 Software Installation ................................................................................................... 47
Windows3.X/DOSSoftwareInstallation........................................................................................ 49
WindowsNT 3.51/4.0SoftwareInstallation ...................................................................................50
OS/2Warp 3.0/Merlin4.0 SoftwareInstallation ............................................................................ 51
InstallingandViewing HOT-671Utilitieson CD ..........................................................................52
4
PREFACE
P
P
HOT-671isa highlyintegratedIBM PC/ATcompatiblesystem board designedto meet
theindustry'smostdemandingdesktop applications.
Basedonthe Intel 82440EXAGPsetchipset, theIntelPentiumTMII processorwith
MMXtechnologyfeatured, and256KBor 512KB Level2 high-performance pipelined
burstsecondary168-pin DIMM socketandsupports up to256MBof EDO RAMand
SDRAM.
HOT-671isequipped with anAcceleratedGraphics Port (A.G.P.),ahigh-performance
interconnectforgraphic-intensiveapplication,such as3D applications.TheA.G.P. is
independentofthe PCI busandis designedtoexclusively use withgraphical-display
devices.TheHOT-671 supports3.3V A.G.P.deviceswith datatransferrates upto133
MHz,allowingdata throughputof500 MB/sec.
TheIntel's82440EX AGPset chipsetprovides an integratedBusMastering IDEcontrol-
lerwithtwo highperformance IDEinterfaceswhich allowsupto fourIDE devices
connectionandup to 33MB/secof datatransferrates.
Theon-board I/Ocontroller providesstandardPCI/Ofunctions:
floppydriveinterface, two FIFOserialports, an InDAdeviceport and aSPP/EPP/ECP
capable parallel port.
HOT-671isbuilt withthreePCI local busslots providing ahighbandwidth datapathfor
data-movementintensivefunctions such asgraphics,and with oneISAslot.
HOT-671provides thefoundation forcost effective,high performanceand highly
expandableplatforms,whichdeliversthelatestin theIntel PentiumTM IIprocessorand
newadvancedchipsettechnology.
5
SPECFICATION
1
1
TheHOT-671Mainboard iscarefully designedforthe demandingPC userwhowants highperfor-
manceandmany intelligent featuresin a compactpackage:
IntelChipset:
FeaturesIntel's440EX AGPset withI/Osubsystems.
CPUSupport:
Intel Pentium®IIandCeleron processor233 ~333MHz.
VersatileMemorySupports:
Equipped with two DIMM sockets support 168-pin3.3V SDRAM andEDODRAM memory
modules,totalmemory size upto256MB.
Configurablesupportfor ECC(Error CheckingandCorrecting)
PCIandISAExpansionSlots:
Providesthree32-bit PCIslotsand one16-bitISA slot.
AGPSlot:
SupportsAccelerated GraphicsPortcardsforhighperformance,component levelinterconnect
targeted at 3D graphical display applications.
OnboardI/O:
ProvidesoneFloppyport;oneoptionalPS/2 mouseconnector; two high-speedUART compatible
serial ports and one parallel port with ECP and EPP capabilities. Serial Port 2 can also be directed
fromCOM2to the Infrared Moduleforwireless connections.
OnboardPCIBusMasterIDEController:
Two UltraDMA/33 BusMaster IDE Portssupportsfour IDEdevicesup to 33MB/sec IDE trans-
fersandsupports Enhanced PIOModes 3 and4and BusMasterIDE DMA Mode2 devices.
Onboard20-pinATXPower Supply:
ProvidesATXpower connectoronboardsupports soft-on/offfunction.
SystemBIOS:
ProvideslicensedAwardV4.51PGBIOSonFlashEEPROM.
SupportsGreenPC, DMIand BundledwithNCR SCSIBIOS.
ACPI:
Support ACPI(AdvancedConfigurationandPower Interface) function. ACPI provide more
EnergySavingFeatures forthe futureoperatingsystemsupportingOS DirectPowerManagement
(OSPM)functionality.
6
OnBoardAudioController:
OPTi82C933PnP 3DAudioChip.
64VoicesWavetableSynthesizer.
Built-in Qsound Qxpander and OPTiFM Music Synthesizer.
Full-DuplexRecord/Playback atupto48KHz.
CompatiblewithGeneral MIDI,MicrosoftWindows Soundsystemand SoundBlasterPro.
BoardSize:
ATX form factor 244mm x 170mm.
AdvancedFeatures:
CPUPlug& Play--HOT-671 featuringCPUPlug & Playfunction, the userneedn'tto adjust
onboardsystemclock andCPUmultiplier. When the systemfirst power-on, BIOSwillset CPU
clock speed to 233 MHz automatically. If your CPU speed higher than 233 MHz., one thing you
only have to do is entry BIOS to set CPU speed to the higher one.
LowEMI--Spread Spectrumbuiltin - ±1.5%modulation and automaticclockshut-off of unused
PCI/SDRAMSslotstoreducethe EMI.
DualFunctionPowerButton-- Thesystem can beoneof twostates, oneis Suspend modeand
the other is the Soft-off mode. Pushing the power button for less than 4 seconds will place the
systemintoSuspend mode. Whenpushthe powerbuttonfor morethan4 seconds,thesystem
enterstheSoft-off mode.
Wake-On-LAN --The systemwill power-onautomatically byactivating ofLAN.
(Thisfunctionsupport Intel LANcardonly).
ModemRingPower-on --Thesystem willpower-onautomatically byactivatingof modemring.
PS/2Keyboard& Mouse Power-on --Thesystem will power-onautomaticallyby strokekey-
boardordouble clickPS/2mouse.
MoreAdvancedFeatures(optional):
VoltagesMonitoring--Systemvoltages levelsare monitoredtoensure stablecurrentto main
boardcomponents.
Systemvoltagesinclude VCORE and VL2 for CPU, and +5V, +12V, -5V, -12V for system.
FANStatusMonitoring-- Toprevent CPUoverheat,CPU fansismonitored forRPMand failure.
(CPUCoolingFAN withRPM sensorisrequired)
Power-onfromKeyboard/Mouse-- HOT-671 mainboard provides an optional power on function
bystrokeany key (orhot-key)on keyboard ordoubleclick on PS/2mouse.
7
ACCESSORIESOF HOT-671
8
HARDWARECONFIGURATION
2
2
The Pentium™ II & Celeron™ Processor
ThePentiumII and Celeron processoristhe next memberofthe P6 processorfamily. It
combinesthearchitecturaladvancesinthePentium Proprocessor withthe instructionset
extensionsofMMX technology. It isfullycompatible withthehuge base ofIntelarchitec-
ture-basedPCsoftware. Additional, the PentiumII processor deliversnewlevels ofperfor-
manceforadvance mediaand communicationssoftwareincluding powerful,realistic
graphicsandimaging capabilities, videoconference,and theabilityto run full-screen,full-
motionvideo. Thecombination oftheseadvanced technologiesmakes thePentiumII
processortheideal choicefoeexecuting modem 32-bitcompute-intensive and multimedia-
enhancedapplication workloads usingadvanced32-bitoperatingsystems.
ThePentiumII and Celeronprocessor both haveaseparate, 32KB,on-chip,non-blocking L1
cachewhichrun at theprocessorfrequency, Pentium IIprocessoralso has a512KBor
256KB on-board L2 non-blocking cache runs at half the processor speed.
ThePentiumII processor usingSingle Edge Contact(S.E.C.)cartridge packagingtechnol-
ogywhichenables highvolumeavailability, improvedhandling protection.
TheCeleronprocessor usingSingle EdgeProcessorPackage. (S.E.P.P.)
Figure2-0shows the front,rearand topviewsof Pentium IIprocessor(without heat sink
mounted).
Figure2-1shows theprimaryand non-primarysideof Celeronprocessorwithout heatsink
mounted and with heat sink mounted.
Figure 2-1
Figure 2-0
9
What does the RM (Retention Mechanism) consist of
PentiumIIprocessor requires theRetentionMechanism (RM) andtheHeat Sink Supportto
holdthebase processorin theS.E.C.cartridge.
Followinginstallation procedurewilldisplayhowtoinstallthesemechanism. Please
consult to your supplier for the mechanism.
RetentionMechanismpackage consistsof 2separatepartsandthe HeatSink Support
consistsof3 separateparts.
RetentionMechanism(RM) -
PlasticGuidewith captivenuts thatholdthe
S.E.C. Cartridge in the Slot1 connector.
(Referto Figure2-1-1)
RMAttachPin (RMAP) -
Plasticpinsinserted throughthe RMtosecure
ittothe mainboard(four requiredperAssembly).
(Referto Figure2-1-2)
Heat Sink Support Base (HSSBASE) -
Plasticsupportbarmountedtothemainboard
undertheATX heat sink.
(Referto Figure2-1-3)
HSSPin(HSSPIN) -
Plasticpinsinserted through theHSSBASEto secure
ittothe mainboard(tworequired perAssembly).
(Referto Figure2-1-4)
HSSTopBar (HSSTOP) -
PlasticbarthatclipsontotheHSSBASE
throughthefins on theATXheat sink.
(Referto Figure2-1-5)
Figure 2-1-1
Figure 2-1-3
Figure 2-1-4
Figure 2-1-5
Figure 2-1-2
10
Install the Retention Mechanism and Heat Sink Support
Placethemainboard on aworkbench (not inachassis). Besurethat the mainboardis bare
(thatis,no SIMMs, cables,or cards areinstalled).
InstalltheRetentionMechanism:
1.Findsout the RetentionMechanism(RM)
MountingHolesand "Pin 1" markofSlot 1
onHOT-671mainboard.
(RefertoFigure 2-2)
2.Insertthe RetentionMechanism(RM)
around theSlot 1. Besure the SquareCut
Mark ofRMhave thesameorientation of
Slot1pin 1.(Refer toFigure2-3)
3.Insertfour RM AttachPin through theRM
tosecureit tothe mainboard(fourrequired
per Assembly). (Refer to Figure 2-3)
Figure 2-2
Figure 2-3
Table des matières
Autres manuels spacewalker Carte mère
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
