Sony SDT-9000 Series Manuel utilisateur
3-860-829-04(1)
1997 Sony Corporation
DDS Tape Drive
SDT-9000 Series
User’s Guide
2
This document contains proprietary
information which is protected by
copyright.
All rights reserved. No part of this
document may be photocopied,
reproduced or translated to another
language without prior written consent
of Sony.
The information contained in this
document is subject to change without
notice.
SONY MAKES NO WARRANTY
OF ANY KIND WITH REGARD TO
THIS DOCUMENT.
Sony shall not be liable for error
contained herein, indirect, special,
incidental or consequential damages in
connection with the furnishing,
performance or use of this document.
VORSICHT
Diese Ausrüstung erfüllt die
Europäischen EMC-Bestimmungen für
die Verwendung in folgender /
folgenden Umgebung(en):
• Wohngegenden
• Gewerbegebiete
• Leichtindustriegebiete
(Diese Ausrüstung erfüllt die
Bestimmungen der Norm EN55022,
Klasse B.)
Contents
Introduction .......................................4
Product Features........................4
Precautions ................................5
Installation .........................................6
SCSI Connection/Setting the
SCSI ID/Option Switches......6
Mounting Holes........................7
Remodeling from 5.25" Model
to 3.5" Model .........................9
Orientation...............................10
Operation .........................................11
Location of 3 LEDs .................11
LED Indication for
Drive Status .........................12
Drive Operation.......................13
Emergency Cassette Removal
Procedure .............................14
Interface Implementation.................16
Supported SCSI Messages ......16
Supported SCSI Commands....16
Specification ....................................17
Product Specifications.............17
Third Party Support Contacts
(In the USA) ...............................19
Sony Contacts ..................................21
3
SDT-9000 DDS-3 Tape Drive
Conglatulation on your purchase of the Sony DDS-3 drive SDT-9000.
This drive is a high capacity data storage device using 4mm DAT (Digital
Audio Tape) technology. The SDT-9000 drive achieves high data
reliability through Read-After-Write, an additional level of Error
Correction Code, and other features.
The Sony SDT-9000 drive stores data on tape using a standard format
called DDS (Digital Data Storage), DDS-3, DDS-2, DDS-DC and DCLZ
formats. These formats are used by many other DDS tape drive
manufacturers, providing a broad range of compatible tape drives.
The Sony SDT-9000 is fully READ and WRITE compatible with the DDS-
3, DDS-2, DDS and DDS-DC format tapes.
4
Introduction
Product Features
• Supported Formats: DDS-3, DDS-2, DDS, DDS-DC and DCLZ
• High Burst Transfer Rate- 5MB/sec Asynchronous
10MB/sec Synchronous
• Large 2MB Buffer
• 3.5" Standard Height, 5.25" Half Height
• Embedded SCSI Interface
• Supports Variable or Fixed Record Length
• Supports SCSI-2 Sequential-access Devices Command Set
• Read After Write (RAW)
• Frame Rewrite Function
• Three Levels of Error Correction Code (ECC)
• Quick Search (200 times normal Read/Write speed)
• Random Read
• N-Group Write Option
• Dual Partition Option
• SCSI Disconnection/Arbitration
* Assuming 2:1 compression. Actual capacity and transfer rate may vary
since compression is depending upon data type.
Data Capacity
Transfer Rate
(sustained)
SDT-9000
(With Data Compression)
24 GB (typical)*
2.4 MB/sec (typical)*
5
Precautions
Installation
Avoid placing the drive in a location subject to:
– high humidity
– high temperature
– mechanical shock and vibration
– direct sunlight
Operation
* Do not move the drive while it is operating. Doing so may cause a
malfunction.
* Avoid exposing the drive to sudden changes from low to high in
temperature. This may cause water condensation to collect inside the
drive. If the ambient temperature should suddenly rise while the drive is
turned on, wait at least one hour before turning on the drive. If you
attempt to operate the drive immediately after a sudden increase in
temperature, a malfunction may occur.
* Do not turn off the drive while a tape is inside the drive.
Transportation
* Keep the original packing materials for possible future shipments of the
drive.
* Be sure to remove any tapes from drive prior to transportation. After
removing the drive from the computer, repack the drive into its original
packaging.
6
Installation
SCSI Connection/Setting the SCSI ID/Option Switches
Terminator OnSCSI ParityDC Disable
SCSI ID
SCSI ID 2
SCSI ID 1
SCSI ID 0
DC DISABLE
SCSI PARITY
RESERVED
TERMINATOR ON
TERMINATOR POWER
Jumpers
Note :
= OPEN/Jumper not installed
= CLOSED/Jumper
Don’t care
Terminator Power
SCSI ID
2
1
0
D
P
.
R
T
0
1
2
3
4
5
6
7
Terminators
2
1
0
D
P
.
R
T
Disabled
Enabled
SCSI Parity
2
1
0
D
P
.
R
T
Enabled
Disabled
Term Power
2
1
0
D
P
.
R
T
Provided
Not
Provided
Terminators
2
1
0
D
P
.
R
T
Enabled
Disabled
SCSI 50 pin Connector
(Non-shielded)
1
12 V
2
GND
3
GND
4
5 V
Power Connector
7
Mounting Holes
For 3.5" Standard Height (SDT-9000)
(0.83 in)
21±0.3mm (2.36 in)
60±0.3mm
(3.54 in)
90±0.3mm
(0.20 in)
5±0.3mm
(depth 0.12 in)
3-M3 (depth 3mm)
(3.70 in)
94±0.3mm
(4.00 in)
101.6±0.5mm
(1.22 in)
31±0.3mm (1.65 in)
42±0.3mm
(2.76 in)
70±0.3mm (depth 0.12 in)
6-M3 (depth 3mm)
(2.36 in)
60±0.3mm
(3.54 in)
90±0.3mm
(5.75 in)
146±0.5mm
(0.15 in)
3.8±0.5mm
(0.83 in)
21±0.3mm
(0.20 in)
5±0.3mm
(1.62 in)
41.2±0.5mm
(depth 0.12 in)
3-M3 (depth 3mm)
8
For 5.25" Half Height (SDT-9000/R)
4-M3
(5.75 in)
146±0.5mm
(3.70 in)
94±0.3mm
(1.22 in)
31±0.3mm (1.65 in)
42±0.3mm (2.76 in)
70±0.3mm
(3.12 in)
79.2±0.3mm
(2.00 in)
50.7±0.3mm
(5.50 in)
139.6±0.4mm
(5.87 in)
149±0.5mm
(depth 0.12 in)
6-M3 (depth 3mm)
4-M3
(3.12 in)
79.2±0.3mm
(1.87 in)
47.5±0.3mm
(0.39 in)
9.9±0.3mm
(0.86 in)
21.8±0.3mm
4-M3
(3.12 in)
79.2±0.3mm
(1.87 in)
47.5±0.3mm
(1.62 in)
41.2±0.5mm
(0.86 in)
21.8±0.3mm
(0.39 in)
9.9±0.3mm
(
0.28 in
)
7±0.3mm
9
Remodeling from 5.25" Model to 3.5" Model
You can remodel the SDT-9000/R (5.25" model) to the SDT-9000 (3.5"
model) yourself.
1Remove the 2 screws for each side rail.
2Take the side rail off.
Side Rail (L)
Side Rail (R)
10
Orientation
10°10°
10°10°
10°10°
10°10°
Autres manuels pour SDT-9000 Series
2
Table des matières
Autres manuels Sony Stockage
Sony
Sony ERA-MS008 Manuel utilisateur
Sony
Sony BKM-12Y Manuel utilisateur
Sony
Sony MSX-M4GS Manuel utilisateur
Sony
Sony IPELA NSRE-S200 Manuel utilisateur
Sony
Sony USM4GM Manuel utilisateur
Sony
Sony MICROVAULT USM-N Series Manuel utilisateur
Sony
Sony MSX-1G Manuel utilisateur
Sony
Sony SR Series Manuel utilisateur
Sony
Sony WALKMAN CKL-NWE020 Manuel utilisateur
Sony
Sony QDH16 Manuel utilisateur
Sony
Sony SDX-1100V/R Manuel utilisateur
Sony
Sony HD-B1 Manuel utilisateur
Sony
Sony SDT-7000 Series Manuel utilisateur
Sony
Sony PFD23A/3 Manuel utilisateur
Sony
Sony HD-EG5 Manuel utilisateur
Sony
Sony DSR-DU1 Manuel utilisateur
Sony
Sony PMW-RX50 Manuel utilisateur
Sony
Sony PetaSite DMS-B150L Manuel utilisateur
Sony
Sony HD-EG5U Manuel utilisateur
Sony
Sony PXU-HC240 Manuel utilisateur
Manuels Stockage populaires d'autres marques
Spectra Logic
Spectra Logic T-Series Spectra T50e Manuel utilisateur
Panasonic
Panasonic LKM-F931-1 Manuel utilisateur
Tabernus
Tabernus Enterprise Erase E2400 Manuel utilisateur
Rocstor
Rocstor COMMANDER 3F series Manuel utilisateur
HP
HP P9000 Manuel utilisateur
Western Digital
Western Digital Ultrastar Data60 Manuel utilisateur