Sony HDPS-M10 - Data Storage Wallet Manuel utilisateur

HDPS-M10

US Model

Canadian Model

Europe Model

UK Model

Latin America Model

SMAP Model

Australian Model

New Zealand Model

Chinese Model

Hong Kong Model

Korea Model

Japanese Model

SERVICE MANUAL

HDD PHOTO STORAGE

Link

Revision History

Ver. 1.1 2006. 10

Sony EMCS Co.

2006J1600-1

Published by Kohda TEC

9-876-896-12

HDPS-M10

DISASSEMBLY

REPAIR PARTS LIST

ADJUSTMENTS

SPECIFICATIONS

DISASSEMBLY

REPAIR PARTS LIST

ADJUSTMENTS

SPECIFICATIONS

How to use

Acrobat Reader

How to use

Acrobat Reader

Revised-1

— 2 —

HDPS-M10

SPECIFICATIONS

Storage capacity

40 GB

(Formatted with FAT32. 1 GB amounts to

1,000,000,000 bytes.)

Media slots

“Memory Stick” slot ×1

CompactFlash slot ×1

Interface

USB 2.0 (Hi-Speed/Full-Speed)*

*If the connected computer does not support

USB 2.0, transfer speed will be according to

Full-speed USB (12 Mbps).

Connector

USB (mini-B) ×1

Power supply

Lithium-ion rechargeable battery

(internal)

100 - 240 V AC, 50/60 Hz

Power consumption

7.5 W maximum

Ambient conditions

Operatingtemperature:5°Cto40°C(40°F

to 104°F) (temperature gradient less than

10°C/hour (50°F/hour))

Operating humidity: 20% to 80%

(non-condensing)

Dimensions

Approx. 135 ×30 ×92 mm

×1

×3

in.)

(W ×H ×D)

Mass

Approx. 300 g (10.6 oz.)

Supplied accessories

AC power adapter

(SONY, Model HDAC-M1/MCS-AC1) (1)

Carrying case (1)

Hand strap (1)

Indicator label (1)

Operating Instructions (this document)

PhotoDiary software (on the hard disk)

Power cord (1)

Read Me First (1)

USB cable (1)

Warranty card (1)

Design and specifications are subject to

change without notice.

Supported media

“Memory Stick” (“Memory Stick Duo”)

CompactFlash cards (CF cards)

(Type I, II, Microdrive)

—3 —

HDPS-M10

1. Check the area of your repairforunsolderedorpoorly-soldered

connections. Checktheentire board surface for solder splashes

and bridges.

2. Check the interboard wiring to ensure that no wires are

"pinched" or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly

transistors, that were installed during a previous repair. Point

them out to the customer and recommend their replacement.

4. Look for parts which, throughfunctioning, showobvioussigns

of deterioration. Point them out to the customer and

recommend their replacement.

5. Check the B+ voltage to see it is at the values specified.

6. Flexible Circuit Board Repairing

•Keep the temperature of the soldering iron around 270˚C

during repairing.

•Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

•Be careful not to apply force on the conductor when soldering

or unsoldering.

Unleaded solder

Boards requiring use of unleaded solder are printed with the lead-

free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size.)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

•Unleaded solder melts at a temperature about 40°C higher than

ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350°C.

Caution: The printed pattern (copper foil) may peel away if the

heated tip is applied for too long, so be careful!

•Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than

ordinary solder so use caution not to let solder bridges occur such

as on IC pins, etc.

•Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINEWITH

MARK 0ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS

LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE

COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS

APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS

PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0SUR LES

DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT

CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE

REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY

DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU

DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

CAUTION :

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

—4 —

HDPS-M10

TABLE OF CONTENTS

1. DISASSEMBLY ·························································1-1

2. REPAIR PARTS LIST

2-1. EXPLODED VIEWS ······················································2-3

2-1-1.OVERALL SECTION·····················································2-3

2-1-2.TOP CASE SECTION ····················································2-4

2-1-3.PWB ASSEMBLY···························································2-5

3. ADJUSTMENTS

3-1. PREPARATIONS BEFORE ADJUSTMENT ·················3-1

3-1-1.List of Service Tools························································3-1

3-1-2.Preparations ·····································································3-2

3-1-3.Order of Adjustments ······················································3-3

3-2. ADJUSTMENTS·····························································3-4

3-2-1.NTFS format····································································3-4

3-2-2.HDD Self Format ····························································3-4

3-2-3.Stand Alone Copy Check and Final Function

(USB Mode) Check ·························································3-5

3-2-3-1. Stand Alone Copy Check ·········································3-5

3-2-3-2. Final Function (USB Mode) Check ·························3-5

3-2-3-2-1. Preparations ·····························································3-5

3-2-3-2-2. Final Function (USB Mode) Check ·························3-7

3-2-4. USB 1.1 Confirmation Check ·······································3-8

3-2-5. Final Function 2 (USB Mode) Check ···························3-8

3-2-6. Burn In (Read) Check ···················································3-9

3-2-7. Burn In (Write) Check ················································3-10

3-2-8. NTFS format ·······························································3-11

3-2-9. HDD Self Format························································3-11

3-2-10. Photo Diary Software Download ································ 3-11

3-2-11. Firmware Upgrade ······················································3-12

3-2-11-1. Firmware Upgrade ·················································3-12

3-2-11-2. Language Settings··················································3-14

3-2-12. Full Charge Implementation ·······································3-14

HDPS-M10 1-1 1-2E

The following flow chart shows the disassembly procedure.

1. DISASSEMBLY

Screw (M2x3.5) black

Battery cover assembly

Connector

Open the lid (R) assembly in the

direction of the arrow a.

Screw (M2x3.5) black

Open the lid (L) assembly in the

direction of the arrow b.

Flexible flat cable

Top case sub assembly

Note: The foot rubber

cannot be reused.

Screw (M2x3.5) black

Foot rubber

Tapping screw (M2x8) silver

Caution

Note: Be sure to fully charge the

battery after the repair is completed.

Caution

Note: Be sure to fully charge the

battery after the repair is completed.

Caution

Screw (M2x3.5) black

Battery cover assembly

Connector

Battery assembly

Battery plate, Battery plate shee

Battery assembly

Battery plate, Battery plate sheet

Lift the PWB board out from the top

case assembly case.

Two positioning holes

Remove the PWB board

in the direction of the arrow.

Connector

Flexible flat cable

PWB board

Tapping screw (M2x3) silver

Two hooks

Peel off the adhesive side

of the flexible side.

LCD set assembly

Note: When installing the

PWB board, align the

switch position.

Claw

Two claws

Open the top case sub assembly

in the direction of the arrow.

Remove the hard disk drive, Bottom shield ,

etc in the direction of the arrow.

Two shock absorbers A

Two shock absorbers B

Bottom case assembly, Lid (R) assembly,

Lid (L) assembly

Two screws (M3x4) silver

Peel off the sheet.

Absorber bracket A,

Two spacers A, B

Absorber bracket B,

Two spacers A, B

Bottom shield , etc

Hard disk drive, IOM-F2 board,

Flexible flat cable

1-1. DISASSEMBLY

NOTE

HDPS-M10

Link

2. REPAIR PARTS LIST

OVERALL SECTION

TOP CASE SECTION

EXPLODED VIEWS

ACCESSORIES

PWB ASSEMBLY

2-1

HDPS-M10

NOTE:

• -XX, -X mean standardized parts, so they may have some differences from

the original one.

• Items marked “*” are not stocked since they are seldom required for routine

service. Some delay should be anticipated when ordering these items.

• The mechanical parts with no reference number in the exploded views are not

supplied.

• Due to standardization, replacements in the parts list may be different from

the parts specified in the diagrams or the components used on the set.

• CAPACITORS:

uF: µF

• COILS

uH: µH

• RESISTORS

All resistors are in ohms.

METAL: metal-film resistor

METAL OXIDE: Metal Oxide-film resistor

F: nonflammable

• SEMICONDUCTORS

In each case, u: µ, for example:

uA...: µA... , uPA... , µPA... ,

uPB... , µPB... , uPC... , µPC... ,

uPD..., µPD...

When indicating parts by reference number,

please include the board name.

The components identified by mark 0or

dotted line with mark 0are critical for safety.

Replace only with part number specified.

Les composants identifiés par une marque

0sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant

le numéro spécifié.

2. REPAIR PARTS LIST

•Abbreviation

CND : Canadian model

AUS : Australian model

CH : Chinese model

HK : Hong Kong model

KR : Korea model

J : Japanese model

TW : Taiwan model

NZ : New Zealand model

SMAP : Sony MarketingAsia Pacific model

LA : Latin America model

EU : Europe model

US : United States model

UK : United Kingdom model

2-3

2. REPAIR PARTS LIST

HDPS-M10

2-1-1. OVERALL SECTION

Ref. No. Part No. Description Ref. No. Part No. Description

ns : not supplied

1 A-1134-386-A ABSORBER ASSY SERVICE A

2 A-1133-812-A LID (L) ASSY

3 A-1133-873-A BATTERY ASSY (US,CND)

3 A-1146-128-A BATTERY ASSY

(LA UK, EU, AUS, NZ, HK, TW, KR, CH, SMAP)

3 A-1182-732-A BATTERY ASSY (J)

4 A-1133-816-A BATTERY COVER ASSY

5 2-108-513-01 SCREW PRECISION M2X3.5 (BLACK)

6 1-797-315-11 HDD (40GB, HTS424040M9AT00)

7 A-1133-897-A IOM-F2 BOARD, COMPLETE

8 1-829-549-11 CABLE, FLEXIBLE FLAT

9 4-683-253-01 SCREW PRECISION M3X4

10 7-685-102-14 SCREW +P 2X4 TYPE2 NON-SLIT

11 A-1134-387-A ABSORBER ASSY SERVICE B

12 A-1133-813-A LID (R) ASSY

13 7-685-105-14 TAPPING +P 2X8 NON-SLIT

14 A-1133-811-A BOTTOM CASE ASSY

15 4-682-526-01 RUBBER FOOT

16 2-059-938-01 BOTTOM SHIELD

CN201 1-778-652-31 CONNECTOR, FFC (ZIP) 50P (HDD)

2-1. EXPLODED VIEWS

516

(Note)

CN201

PWB assembly

(See page 2-5)

Top case section

(See page 2-4)

Note :

When the TOP CASE ASSY SERVICE (Ref. No.52

on page 2-4) is going to be replaced by the TOP

CASE ASSY SERVICE with suffix-B, do not install

the two parts that are shown as “ns” (not supplied)

above.

2-4

2. REPAIR PARTS LIST

HDPS-M10

2-1-2. TOP CASE SECTION

Ref. No. Part No. Description Ref. No. Part No. Description

ns : not supplied

51 X-2067-598-1 LCD WINDOW ASSY

52 A-1133-810-B TOP CASE ASSY SERVICE (Note)

53 A-1133-815-A HOLD KEY ASSY SERVICE

54 2-629-870-01 LCD DAMPER

55 A-1133-872-A LCD SET

56 4-671-885-01 SCREW, TAPPING, SPECIAL

57 2-637-218-01 LCD HOLDER INSULATOR

59 2-637-219-01 LCD FPC TAPE

60 2-629-873-01 POWER BUTTON

61 2-629-871-01 CANCEL BUTTON

(Note)

Note :

When the TOP CASE ASSY SERVICE (Ref. No.52

on this page) is going to be replaced with the TOP

CASE ASSY SERVICE with suffix-B, do not install

the two parts that are shown as “ns”(not supplied)

on page 2-3.

2-5

2. REPAIR PARTS LIST

HDPS-M10

CN3

CN7

CN8

CN5

CN6

103

102

101

104

CN4

CN1

2-1-3. PWB ASSEMBLY

ns : not supplied

101 2-108-394-01 GASKET (PWB)

102 7-627-553-47 PRECISION SCREW +P 2X4 TYPE 3

103 1-818-690-11 CONNECTOR, CARD (CF CARD)

104 A-1133-809-A PWB ASSY SERVICE

CN1 1-819-856-61 CONNECTOR, FFC/FPC (ZIF) 30P (LCD)

CN3 1-816-617-11 HEADER PIN (CF CARD)

CN4 1-817-653-11 MEMORY STICK CONNECTOR

CN5 1-817-998-11 JACK, DC

Ref. No. Part No. Description Ref. No. Part No. Description

CN6 1-817-171-11 MINI-B USB CONNECTOR 5PIN

CN7 1-770-160-21 PIN, CONNECTOR (PC BOARD) 2P (BATTERY)

*CN8 1-580-055-21 PIN, CONNECTOR (SMD) 2P (BACKLIGHT)

0F1 1-576-415-11 FUSE, MICRO (1608 TYPE) (2A/32V)

S1 1-572-595-11 SWITCH, TACTIL (REFLOW TYPE)

(COPY/CANCEL)

S2 1-572-595-11 SWITCH, TACTIL (REFLOW TYPE)

(COPY/CANCEL)

S3 1-771-627-11 SWITCH, TACTIL (POWER)

S4 1-762-078-11 SWITCH, SLIDE (HOLD)

Note :

The components identified by

mark 0or dotted line with mark

0are critical for safety.

Replace only with part number

specified.

Note :

Les composants identifiés par

une marque 0sont critiques

pour la sécurité.

Ne les remplacer que par une

pièce portant le numéro spécifié.

Autres manuels pour HDPS-M10 - Data Storage Wallet

Table des matières

Autres manuels Sony Stockage

Sony

Sony StorStation LIB-81 Manuel utilisateur

Sony

Sony Memory Stick PRO-HG Duo HX Series Manuel utilisateur

Sony

Sony MSAC-US40 - MemoryStick Flash Memory Card USB 2.0... Manuel utilisateur

Sony

Sony DSR-DU1 Manuel utilisateur

Sony

Sony HD-EG5U Manuel utilisateur

Sony

Sony MICROVAULT USM-N Series Manuel utilisateur

Sony

Sony HDPS-M1 Manuel

Sony

Sony SCPH-20401 Manuel utilisateur

Sony

Sony AIT-SDX460 Instructions d'installation

Sony

Sony PCGA-HDX10 Manuel utilisateur

Sony

Sony MSX-M1GS Operating Instructions (Memory Stick... Manuel utilisateur

Sony

Sony IPELA NSRE-S200 Manuel utilisateur

Sony

Sony SDT-S11000 Manuel utilisateur

Sony

Sony MS-A512N Manuel utilisateur

Sony

Sony M2 MS-A Series Manuel utilisateur

Sony

Sony VGN-BX660P Mode d’emploi

Sony

Sony HD-SP Series Manuel utilisateur

Sony

Sony USM128B Manuel utilisateur

Sony

Sony MicroVault USM1GJ Manuel utilisateur

Sony

Sony StorStation AITi1040 Manuel utilisateur

Sony

Sony USM1GJ Manuel utilisateur

Sony

Sony SDT 11000 - DDS Tape Drive Manuel utilisateur

Sony

Sony Vaio VGP-UHDM10 Manuel utilisateur

Sony

Sony MSH-128S2 Operating Instructions (primary... Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur