Sony MDR-IF320RK2 Manuel utilisateur
3
00/00-01_MDRIF320RK2.11EFGS
3-858-299-12(1)
© 1996 by Sony Corporation
MDR-IF320RK2
Cordless Stereo
Headphone System
Operating Instructions page 2
Mode d’emploi page 12
Bedienungsanleitung seite 22
Manual de instrucciones página 32
2
01/02-11_MDRIF320RK2.12E
WARNING
To prevent fire or shock hazard,
do not expose the unit to rain or
moisture.
To avoid electrical shock, do not
open the cabinet. Refer servicing
to qualified personnel only.
WARNING
You are cautioned that any changes or
modifications not expressly approved
in this manual could void your
authority to operate this equipment.
Owner’s Record
The model number is located at the
back of the transmitter and the left
inner side of the headband.
The serial number is located at the
bottom of the transmitter and the right
inner side of the headband.
Record these numbers in the spaces
provided below. Refer to them
whenever you call upon your Sony
dealer regarding this product.
Model No. MDR-IF320RK2
Transmitter TMR-IF320R
Headphones MDR-IF320R2
Serial No.
Transmitter
Headphones
3
01/02-11_MDRIF320RK2.12E
Table of contents
Getting started
Unpacking .......................................... 4
Setting up the transmitter ................ 4
Charging the
headphones’ battery ...................... 6
Operating the system
Listening to a program ...................... 7
The effective areas of the
transmitter........................................ 8
Replacing the ear pads ...................... 8
Additional information
Precautions .......................................... 9
Troubleshooting ................................. 9
Specifications .................................... 11
Welcome!
Thank you for purchasing the Sony
MDR-IF320RK2 Cordless Stereo
Headphones System. Before operating
the unit, please read this manual
thoroughly and retain it for future
reference.
Some features are:
• Cordless system that allows you to
listen to a program free from the
restriction of a cord.
• Broad horizontal listening area that
gives you superb sound virtually
anywhere in the room.
• Self-adjusting headband for fitting
your head perfectly.
• The power of the headphones turns
on and off automatically every time
you put the headphones on and off
(Auto power on/off function).
• The VOL control adjusts the volume
level of both channels.
• The lightweight rechargeable battery
built into the headphones allows an
economical operation.
4
01/02-11_MDRIF320RK2.12E
Stereo system,
TV, VCR, etc.
Transmitter
to AUDIO IN B jack
Connecting
cord (supplied)
to LINE OUT
or REC OUT
Right
channel
(red)
Left
channel
(white)
(Getting started
Unpacking
Check that you have the following
items:
• The transmitter
• AC power adaptor
• Connecting cord (phono plugs ˜
stereo mini plug)
• Unimatch plug adaptor (stereo mini
jack nstereo phone plug)
• The headphones
Setting up the
transmitter
1Connect the transmitter to audio/
video equipment. Select one of the
hookups below depending on the
jack type:
aTo connect to LINE OUT or REC
OUT jacks
5
01/02-11_MDRIF320RK2.12E
3Connect the transmitter to a power
source.
Notes
• Do not connect to the AUDIO IN A jack and B
jacks at the same time. If you do so, the audio
signals may be mixed.
• Use only the supplied AC power adaptor. Do
not use any other AC power adaptor.
• If the plug of the AC power adaptor does not fit
in the AC outlet, use the supplied AC plug
adaptor.
• When you connect the connecting cord directly
to an earphone jack, the audio signal will not be
output through the right channel. In such a
case, use the separately sold PC-236HG plug
adaptor.
to headphones
jack (stereo
mini plug)
bTo connect to a headphones jack
2If your AC power adaptor is
equipped with a voltage selector,
before connecting the AC power
adaptor to an AC outlet, set it to
the operating voltage in your area
with a screw driver.
110V 120V 220V 240V
VOLTAGE
SELECTOR
Transmitter
Right channel
(red)
Left channel (white)
to AUDIO IN A jacks
Connecting cord
(supplied)
to headphones
jack (stereo
phone plug)
Discman,
WALKMAN*, TV,
VCR, etc.
Unimatch plug
adaptor
(supplied)
AC power adaptor (supplied)
Transmitter
to DC IN
9V jack
AC power
adaptor
(supplied)
to an AC
outlet
Polarity of the plug
* WALKMAN is a registered trademark of Sony
Corporation.
6
01/02-11_MDRIF320RK2.12E
When the indicator is not lit
Check the connection to make sure that
the contact pins are properly fitted into
the contact holes on the headphones, or
if the headphones are rested on the
transmitter correctly.
To recharge the headphones’
battery after use
To charge the battery, follow steps 1
and 2.
• Since little electric current is used for
charging, there is no need to worry
about overcharging.
• It allows operation for about one
hour by charging the battery for
about three hours.
• It takes about 24 hours to fully charge
the battery. The fully charged
battery allows operation for about
seven hours.
Check the remaining power of the
headphones’ battery
Pull the right side headband, and check
that the headphones’ indicator lights in
red. You can now use the headphones.
Charge the battery, if the power
indicator light is weak or turned off.
Note
During recharging, the transmitter is turned off
automatically.
Charging the
headphones’
battery
Using the headphones for the first
time
The headphones are powered by their
built-in rechargeable battery. When
you use the headphones for the first
time, proceed to charge in the
following way.
1Connect the supplied AC power
adaptor to the transmitter.
2Rest the headphones on the
transmitter so that the contact pins
fit into the contact holes on the
headphones. The charging
indicator lights.
Transmitter
to DC IN
9V jack
AC power
adaptor
(supplied)
to an AC
outlet
7
01/02-11_MDRIF320RK2.12E
Auto power on/off function
When you remove the headphones, the
power turns off automatically. Do not
stretch the right side headband when
not using the headphones, otherwise
the headphones will be switched on.
Mute function
If a hissing noise is heard when the
infrared rays are obstructed, or the
headphones are used outside of the
effective range (see the next section),
the mute function will be activated and
the sound will not be heard from the
headphones. To restore the sound,
move nearer toward the transmitter or
remove the obstruction.
When no audio signal is received for
more than approximately five
minutes
The transmitter will be turned off
automatically.
After listening to a program
Take the headphones off and rest them
away onto the transmitter. The
transmitter power will automatically
be turned off, and the charging
indicator lights. Headphone battery is
continuously charged when the
headphones is placed on the
transmitter.
• Since little electric current is used for
charging, there is no need to worry
about over charging.
(Operating the system
Listening to a
program
1Turn on the audio/video
equipment connected to the
transmitter.
When the audio signal is input, the
transmitter turns on automatically
and the infrared emitters glow. If
the transmitter is connected to the
headphone jack, set the volume
control of the audio source
equipment as high as possible but
not so high that the audio signal
gets distorted. (Around level 5 or 6
on the volume control should be
appropriate.)
2Put on the headphones and the
power turns on automatically.
The power indicator glows red
when the power turns on.
3Adjust the volume.
(Continue to next page)
8
01/02-11_MDRIF320RK2.12E
Replacing the ear
pads
When the ear pads become dirty or
damaged, you can get replacements
from your Sony dealer. Replace them
as illustrated below.
1Remove the old ear pad by pulling
it out of the groove on the housing.
2Place the new ear pad on the
housing and insert the edge of the
pad onto the groove as illustrated.
Make sure that the entire edge of the
ear pad is securely inserted into the
groove.
Listening to a program
• As MDR-IF320RK2 Cordless Stereo
Headphone System is not affected by
the memory effect of Ni-Cd battery, it
is suggested that the headphones be
rested on the transmitter whenever
not in use so that headphones’
battery is always charged.
Note
The infrared emitters light up when the
transmitter is turned on. The brightness of the
emitters may not be uniform, however, this is not
a malfunction.
The effective areas
of the transmitter
The illustration below shows the
approximate area covered by the
infrared rays emitted from the
transmitter.
Notes
• If you use the headphones at too great a
distance from the transmitter, you may hear a
hissing noise and if there is an object between
the receiver and the transmitter, the sound may
be interrupted. These phenomena are inherent
to infrared ray communication and do not
mean that there is a problem with the unit
itself.
• Do not cover the infrared sensors with your
hands or hair.
• The infrared rays will not penetrate walls or
opaque glass, therefore, be sure to stay within
sight of the transmitter.
• When you use the headphones inside the area
illustrated in the diagrams, the transmitter can
be placed in the front, behind or by the side of
the listener.
Infrared ray
Transmitter
Approx. 7 m (23 ft.)
Approx. 3 m
(1181/8in.)
Approx. 3 m
(1181/8in.)
9
01/02-11_MDRIF320RK2.12E
Troubleshooting
(Additional information
Precautions
• The CE mark on the unit is valid only
for products marketed in the
European Union.
• When the transmitter is not to be
used for a long period of time,
disconnect the AC power adaptor
from the AC outlet holding the plug.
Do not pull on the cord.
• Do not leave the cordless stereo
headphones system in a location
subject to direct sunlight, heat or
moisture.
• The nameplate indicating operating
voltage, power consumption, etc., is
located on the bottom of the AC
power adaptor (European models
only).
Notes on headphones
Preventing hearing damage
Avoid using headphones at high
volume. Hearing experts advise
against continuous, loud and extended
play. If you experience a ringing in
your ears, reduce the volume or
discontinue use.
Caring for others
Keep the volume at a moderate level.
This will allow you to hear outside
sounds and to be considerate to the
people around you.
If you have any questions or problems
concerning the system that are not
covered in this manual, please consult
the nearest Sony dealer.
Be sure to bring the headphones and
the transmitter to the Sony dealer when
requiring repair work. (Continue to next page)
Problem
No sound/
Muffled
sound
Solution
Check the connection of the
audio/video equipment or
the AC power adaptor.
Check that the audio/video
equipment is turned on.
Turn up the volume on the
connected audio/video
equipment, if the
transmitter is connected to
the headphones jack.
(Around level 5 or 6 on the
volume control should be
appropriate.)
The mute function is
activated.
• Check if there is any
object between the
transmitter and the
headphones.
• Use the headphones near
the transmitter.
• Change the position and
angle of the transmitter.
The headphones’ power
indicator light is weak or
turned off.
• Charge the rechargeable
battery because the
headphones’ battery is
weak, or if the power
indicator is still off after
charging the battery, take
the headphones to a Sony
dealer for a replacement
of the rechargeable
battery.
10
01/02-11_MDRIF320RK2.12E
Problem
Loud
background
noise
Solution
If the transmitter is
connected to the
headphones jack, turn up
the volume of the connected
audio/video equipment.
(Around level 5 or 6 on the
volume control should be
appropriate.)
The headphones’ power
indicator light is weak or
turned off.
• Charge the rechargeable
battery because the
headphones’ battery is
weak, or if the power
indicator is still off after
charging the battery, take
the headphones to a Sony
dealer for a replacement
of the rechargeable
battery.
Problem
Distortion
Loud
background
noise
Solution
If the transmitter is
connected␣ to␣ the␣ headphones
jack, turn down the volume
of the connected audio/
video equipment.
(Around level 5 or 6 on the
volume control should be
appropriate.)
The headphones’ power
indicator light is weak or
turned off.
• Charge the rechargeable
battery because the
headphones’ battery is
weak, or if the power
indicator is still off after
charging the battery, take
the headphones to a Sony
dealer for a replacement
of the rechargeable
battery.
Move closer to the
transmitter. As you move
away from the transmitter,
more noise is likely to be
heard. This is inherent to
infrared ray communication
and does not mean that
there is a problem with the
unit itself.
Check that there is no object
between the transmitter and
the headphones.
Check that the infrared
sensors are not covered
with your hands or hair.
Change the position or
angle of the transmitter.
• The headphones are used
by a window where the
sunlight is too strong.
nDraw the curtains/
blind to shut out the
direct sunlight, or use
the headphones away
from the sunlight.
Table des matières
Langues :
Autres manuels Sony Casque audio
Sony
Sony MDR-EX38iP Manuel utilisateur
Sony
Sony MDR-ZX500 Manuel utilisateur
Sony
Sony MDR-EX15LP Manuel utilisateur
Sony
Sony MDR-10R Manuel utilisateur
Sony
Sony MDR-EX86LP Manuel utilisateur
Sony
Sony MDR-Q68LW Manuel utilisateur
Sony
Sony MDR-DS5100 Manuel utilisateur
Sony
Sony MDR-V55 Manuel utilisateur
Sony
Sony DIGITAL NOISE CANCELING HEADPHONES... Manuel utilisateur
Sony
Sony MDR-XB40EX Manuel utilisateur
Sony
Sony MDR-770LP Manuel utilisateur
Sony
Sony MDR-EX1000 Manuel utilisateur
Sony
Sony MDR NC50 Manuel utilisateur
Sony
Sony MDR-XB800 Manuel utilisateur
Sony
Sony MDR-IF5K Manuel utilisateur
Sony
Sony STEREO HANDPHONES MDR-Q68LW Manuel utilisateur
Sony
Sony HP-SE11 Manuel utilisateur
Sony
Sony DR-EX12iP/BLU Manuel utilisateur
Sony
Sony MDR-XB300 Manuel utilisateur
Sony
Sony MDR-HW700DS Manuel utilisateur
