Sonance ARCHITECTURAL Series Manuel utilisateur

Determine the location for the mounting platform.

Ensure there is adequate room for the BPS6

subwoofer at the location of the platform.

The speaker opening must be located within

12” (305mm) of the BPS6 to allow the port

tube to reach through the platform.

Place the mounting template on the side of

the joist and drill four 1/2” (12.7mm) holes

through the joist at the locations shown on

the mounting template.

Attach the mounting platform to the joists.

See mounting platform quickstart guide or visit

www.sonance.com/in-wall-in-ceiling/

architectural-series for detailed

installation manual.

Hold the side of the BPS6 with the rubber

damping pad up against the side of the joist

and install the four lag screws and washers to

secure the BPS6 in place.

3 4

12” (305mm)

BPS6

Port tube

(1) Quickstart guide

(1) Bandpass subwoofer w/ port tube

(1) Cardboard mounting template

Mounting screws & washers:

(4) 5/16” x 2” lag screws (for thinner beams)

(4) 5/16” x 3” lag screws (for thicker beams)

(4) 5/16” washers

Box Contents

Bandpass subwoofer can be installed in joists spaced 16” on center or greater.

AS BANDPASS STEREO SUBWOOFER QUICKSTART GUIDE

BPS6

SONANCE ARCHITECTURAL SERIES®

Sonance and Architectural Series are registered trademarks of Dana Innovations.

Due to continuous product improvement, all features and specifications are subject to change without notice.

For the latest Sonance product specification information, visit our website: www.sonance.com

SONANCE • 212 Avenida Fabricante • San Clemente, CA 92672-7531 USA

(800) 582-7777 or (949) 492-7777 • FAX: (949) 361-5151 • Technical Support: (800) 582-0772

www.sonance.com

06.05.1433-5946

On the end of the BPS6 port tube there is a tether.

The tether will be used later to guide the BPS6 port

tube through the mounting platform opening.

Position end of port tube as close as possible

to back of mounting platform. Loop tether into

the anchored zip tie and secure. This process

ensures that bandpass connector is easily

attached later and other tradespersons won’t

infringe on port tube assembly area.

5 6

7 8

Tether into

zip tie

Tether

For wiring diagrams &

detailed eManual scan

the QR code or visit

www.sonance.com/

in-wall-in-ceiling/

architectural-series

Secure the wires with a zip tie near the

terminals to prevent accidental removal by

another tradesperson.

Attach the four conductor wires from the

amplifier to the input terminals on the end of

the BPS6. Positive wires to red terminals and

negative wires to black terminals. Run the

speakers wires to amplifier location and run

signal test with 9V battery. NOTE: Port tube

contains foam plug with tether, make sure

pressure levels don’t expel the foam and

tether. Do not connect the voice coils

in parallel.

Ce manuel convient aux modèles suivants

Autres manuels Sonance Subwoofer

Sonance

Sonance Cinema Series SUB 12-250 Manuel utilisateur

Sonance

Sonance Virtuoso A800D Manuel utilisateur

Sonance

Sonance HS12T SUB Manuel utilisateur

Sonance

Sonance BPS6 Manuel utilisateur

Sonance

Sonance Cinema Series CINEMA SUB Manuel utilisateur

Sonance

Sonance LS47SAT Manuel utilisateur

Sonance

Sonance XBW Manuel utilisateur

Sonance

Sonance ThinLIne Series Manuel utilisateur

Sonance

Sonance i12 Manuel utilisateur

Sonance

Sonance Landscape Series Manuel utilisateur

Sonance

Sonance Son Of Sub Manuel utilisateur

Sonance

Sonance BPS6 TL Manuel utilisateur

Sonance

Sonance LS15SUB Manuel utilisateur

Sonance

Sonance D8 Manuel utilisateur

Sonance

Sonance HS10SUB Manuel utilisateur

Sonance

Sonance Cinema Series SUB 10-150 Manuel utilisateur

Sonance

Sonance RK10W Manuel utilisateur

Sonance

Sonance LS10SUB Manuel utilisateur

Sonance

Sonance BPS6 Manuel utilisateur

Sonance

Sonance BPS6 Manuel utilisateur

Sonance

Sonance HS12T SUB Manuel utilisateur

Sonance

Sonance BPS-1 Manuel utilisateur

Sonance

Sonance VP10SUB NC Manuel utilisateur

Sonance

Sonance BPS-1 Manuel utilisateur

Manuels Subwoofer populaires d'autres marques

Sony

Sony XS-AW8 Manuel utilisateur

Sony

Sony XS-L836 Manuel utilisateur

B&C Speakers

B&C Speakers 15 HPL 76W Manuel utilisateur

Velodyne

Velodyne DD-18+ Manuel utilisateur

Hifonics

Hifonics HW-12 Guide de démarrage rapide

Magnat Audio

Magnat Audio ADR 130 BP Manuel utilisateur

Blitz

Blitz BZP106 Manuel utilisateur

Technics

Technics SB-AS500 Manuel utilisateur

Lyngdorf

Lyngdorf BW-2 Manuel utilisateur

Lyngdorf

Lyngdorf BW-3 Manuel utilisateur

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Manuel utilisateur

REL Acoustics

REL Acoustics Q Series Manuel utilisateur

Pioneer

Pioneer Elite S-W1EX Manuel utilisateur

L-Acoustics

L-Acoustics KIVA SB15M Guide de démarrage rapide

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Manuel utilisateur

KEF

KEF KUBE 200 Manuel utilisateur

Yamaha

Yamaha SW500 Manuel utilisateur

Adam

Adam Sub15 Manuel utilisateur